Numerical Investigation of Combined Top and Lateral Blowing in a Peirce-Smith Converter
-
D. K. Chibwe
,
G. Akdogan
Abstract
Typical current operation of lateral-blown Peirce-Smith converters (PSCs) has the common phenomenon of splashing and slopping due to air injection. The splashing and wave motion in these converters cause metal losses and potential production lost time due to intermittent cleaning of the converter mouth and thus reduced process throughput. Understanding of the effect of combined top and lateral blowing could possibly lead to alternative technology advancement for increased process efficiency. In this study, computational fluid dynamics (CFD) simulations of conventional common practice (lateral blowing) and combined (top and lateral blowing) in a PSC were carried out, and results of flow variables (bath velocity, turbulence kinetic energy, etc.) were compared. The two-dimensional (2-D) and three-dimensional (3-D) simulations of the three-phase system (air–matte–slag) were executed utilizing a commercial CFD numerical software code, ANSYS FLUENT 14.0. These simulations were performed employing the volume of fluid and realizable 
turbulence models to account for multiphase and turbulent nature of the flow, respectively. Upon completion of the simulations, the results of the models were analysed and compared by means of density contour plots, velocity vector plots, turbulent kinetic energy vector plots, average turbulent kinetic energy, turbulent intensity contour plots and average matte bulk velocity. It was found that both blowing configuration and slag layer thickness have significant effects on mixing propagation, wave formation and splashing in the PSC as the results showed wave formation and splashing significantly being reduced by employing combined top- and lateral-blowing configurations.
References
1. LiowJL, GrayNB. Slopping resulting from gas injection in a Peirce-Smith converter: water modeling. MetallMater Trans B1990;21:987–96.10.1007/BF02670269Suche in Google Scholar
2. CastillejosAH, BrimacombeJK. Measurement of physical characteristics of bubbles in gas–liquid plumes: part II. Local properties of turbulent air-water plumes in vertically injected jets. Metall Mater Trans B1987;18:659–71.10.1007/BF02672882Suche in Google Scholar
3. MazumdarD, GuthrieRI. Mixing models for gas stirred metallurgical reactors. Metall Mater Trans B1986;17:725–33.10.1007/BF02657134Suche in Google Scholar
4. StapurewiczT, ThemelisNJ. Mixing and mass transfer phenomena in bottom-injected gas–liquid reactors. Can Metall Q1987;26:123–8.10.1179/cmq.1987.26.2.123Suche in Google Scholar
5. ChibweDK, AkdoganG, AldrichC, EricRH. CFD modelling of global mixing parameters in a Peirce-Smith converter with comparison to physical modelling. Chem Prod Process Model2011;6:22–52.10.2202/1934-2659.1584Suche in Google Scholar
6. VaarnoJ, PitkäläJ, AhokainenT, JokilaaksoA. Modelling gas injection of a Peirce-Smith-converter. Appl Math Model1998;22:907–20.10.1016/S0307-904X(98)10036-7Suche in Google Scholar
7. ValenciaA, RosalesM, ParedesR, LeonC, MoyanoA. Numerical and experimental investigation of the fluid dynamics in a Teniente type copper converter. Int Commun Heat Mass Transf2006;33:302–10.10.1016/j.icheatmasstransfer.2005.12.009Suche in Google Scholar
8. HaidaO, BrimacombeJK. Physical-model study of the effect of gas kinetic energy in injection refining processes. Trans Iron Steel Inst Jpn1985;25:14–20.10.2355/isijinternational1966.25.14Suche in Google Scholar
9. ValenciaA, ParedesR, RosalesM, GodoyE, OrtegaJ. Fluid dynamics of submerged gas injection into liquid in a model of copper converter. Int Commun Heat Mass Transf2004;31:21–30.10.1016/S0735-1933(03)00198-2Suche in Google Scholar
10. SinhaUP, McNallanMJ. Mixing in ladles by vertical injection of gas and gas-particle jets – a water model study. Metall Mater Trans B1985;16:850–3.10.1007/BF02667523Suche in Google Scholar
11. KoohiAH, HalaliM, AskariM, ManzariMT. Investigation and modeling of splashing in the Peirce Smith converter. ChemProdProcessModel2008;3:2.10.2202/1934-2659.1132Suche in Google Scholar
12. Ramirez-ArgaezMA. Numerical simulation of fluid flow and mixing in gas-stirred ladles. MaterManufacturingProcess2008;23:59–68.10.1080/10426910701524568Suche in Google Scholar
13. KylloAK, RichardsGG. A kinetic model of Pierce Smith converter: part II. Model application and discussion. Metall Trans B1998;29b:251–9.10.1007/s11663-998-0028-8Suche in Google Scholar
14. RosalesM, FuentesR, RuzP, GodoyJ. A fluid dynamic simulation of a Teniente converter. Copper International Conference – Cobre, 991999:107–21.Suche in Google Scholar
15. SchwarzMP. Simulation of gas injection into liquid melts. Appl Math Model1996;20:41–51.10.1016/0307-904X(95)00109-WSuche in Google Scholar
16. ValenciaA, CordovaM, OrtegaJ. Numerical simulation of gas bubbles formation at a submerged orifice in a liquid. Int Commun Heat Mass Transf2002;29:821–30.10.1016/S0735-1933(02)00372-XSuche in Google Scholar
17. HanJW, HeoSH, KamDH, YouBD, PakJJ, SongHS. Transient fluid flow phenomena in a gas stirred liquid bath with top oil layer – approach by numerical simulation and water model experiments. ISIJ Int2001;41:1165–72.10.2355/isijinternational.41.1165Suche in Google Scholar
18. RealC, HoyosL, CervantesF, MirandaR, Palomar-PardaveM, BarronM, et al. Fluid characterization of copper converters. MecánicaComputacional2007;26:1311–23.Suche in Google Scholar
19. MarcusonSW, LandoltCA, AmsonJH, DaviesH. Converter and method for top blowing nonferrous metal. USA patent 5180423, 1993.Suche in Google Scholar
20. ShihTH, LiouWW, ShabbirA, YangZ, ZhuJ. A new k-[epsilon] eddy viscosity model for high Reynolds number turbulent flows. Comput Fluids1995;24:227–38.10.1016/0045-7930(94)00032-TSuche in Google Scholar
21. AnsysI. ANSYSFLUENTtheoryguide.Release 14.0 edn. USA: ANSYS Inc, 2011.Suche in Google Scholar
22. MazumdarD, EvansJW. Macroscopic models for gas stirred ladles. ISIJ Int2004;44:447–61.10.2355/isijinternational.44.447Suche in Google Scholar
©2013 by Walter de Gruyter Berlin / Boston
Artikel in diesem Heft
- Masthead
- Masthead
- Research Article
- Study of Phase Distribution of a Liquid-Solid Circulating Fluidized Bed Reactor Using Abductive Network Modeling Approach
- Optimization of Trickle-Bed Reactors (TBRs) for Hydrodesulfurization (HDS) and Hydrodearomatization (HDA) of Diesel using Single and Multiple Objectives
- Far-Infrared Drying Characteristics of Mushroom Slices
- Numerical Investigation of Combined Top and Lateral Blowing in a Peirce-Smith Converter
Artikel in diesem Heft
- Masthead
- Masthead
- Research Article
- Study of Phase Distribution of a Liquid-Solid Circulating Fluidized Bed Reactor Using Abductive Network Modeling Approach
- Optimization of Trickle-Bed Reactors (TBRs) for Hydrodesulfurization (HDS) and Hydrodearomatization (HDA) of Diesel using Single and Multiple Objectives
- Far-Infrared Drying Characteristics of Mushroom Slices
- Numerical Investigation of Combined Top and Lateral Blowing in a Peirce-Smith Converter
