Skip to main content
Article
Licensed
Unlicensed Requires Authentication

A model for 3-D study of rearrangement in liquid phase sintering

  • EMAIL logo
Published/Copyright: January 26, 2022
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 95 Issue 11

Abstract

The rearrangement process assumes that if there is good wetting between liquid and solid phase, solid particles will rearrange themselves under the action of surface tension forces, producing more stable green packing. This paper outlines a computer-based method for calculation of the capillary force during liquid phase sintering based on a two-spherical-particle model and circle approximation for computation of the liquid bridge meniscus. The method was applied to a 3-D study of the rearrangement during liquid phase sintering using a multi-particle model. The results obtained have shown that rearrangement is essentially governed by geometrical factors where uniformity of initial particle packing and a high degree of mixing homogeneity are prerequisites for effective densification.

Keywords: Liquid phase sintering; Rearrangement; Capillary force; Computer simulation
Prof. Dr. Zoran S. Nikolic University of Nish Faculty of Electronic Engineering Department of Microelectronics P.O. Box 73, 18000 Nish, Serbia and Montenegro Tel.: +381 18 529 404 Fax: +381 18 524 931

References

[1] W.D. Kingery: J. Appl. Phy. 30 (1959) 301.10.1063/1.1735155Search in Google Scholar

[2] W.J. Huppmann, H. Riegger: Acta Metall. 23 (1975) 965.10.1016/0001-6160(75)90010-3Search in Google Scholar

[3] V. Smolej, S. Pejovnik, W.A. Kaysser: Powder Metall. Int. 14 (1982) 34.Search in Google Scholar

[4] R.M. German: Liquid Phase Sintering, Plenum Press, New York (1985).10.1007/978-1-4899-3599-1Search in Google Scholar

[5] J. Svoboda, H. Riedel, R. Gaebel: Acta mater. 44 (1996) 3215.10.1016/1359-6454(95)00440-8Search in Google Scholar

[6] H. Riegger, J.A. Pask, H.E. Exner, in: G.C. Kuczynski (Ed.), Sintering Processes, Plenum Press, New York (1980) 219.10.1007/978-1-4899-5301-8_19Search in Google Scholar

[7] B.E. Magee, J. Lund: Z. Metallkd. 67 (1976) 596.Search in Google Scholar

[8] A. Belhadjhamida, R.M. German, in: Advances in Powder Metallurgy and Particulate Materials, Metal Powder Industries Federation, Princeton, NJ 3 (1993) 85.Search in Google Scholar

[9] J.M. Chaix: C. R. Acad. Sci. Paris, Serie II, 316 (1993) 855.Search in Google Scholar

[10] J.M. Chaix, in: Powder Metallurgy World Congress PM ’94, Paris, Vol. II, (1994) 1557.Search in Google Scholar

[11] J.M. Chaix, S.M. Lee, C.L. Martin, in: B.D. Stojanovic, V.V. Skorokhod, M.V. Nikolic (Eds.), Advanced Science and Technology of Sintering, Kluwer Academic/Plenum Publishers, New York (1999) 55.10.1007/978-1-4419-8666-5_5Search in Google Scholar

[12] K.S. Hwang, R.M. German, F.V. Lenel: Metall. Trans. A, Vol. 18A (1987) 11.10.1007/BF02646216Search in Google Scholar

[13] V.N. Eremenko, Yu.V. Naidich, I.A. Lavrinenko: Liquid Phase Sintering, Consultants Bureau, New York (1970).10.1007/978-1-4757-5665-4Search in Google Scholar

[14] R.B. Heady, J.W. Cahn: Metall. Trans. 1 (1970) 185.10.1007/BF02819260Search in Google Scholar

[15] V. Smolej, S. Pejovnik: Z. Metallkd. 67 (1976) 603.Search in Google Scholar

[16] M. Hansen, K. Anderko: Constitution of Binary Alloys, McGraw-Hill, New York (1958).10.1149/1.2428700Search in Google Scholar

[17] H.E. Exner, G. Petzow, P. Wellner, in: G.C. Kuczynski (Ed.), Sintering and Related Phenomena, Plenum Press, New York (1973) 351.10.1007/978-1-4615-8999-0_30Search in Google Scholar

[18] W.J. Huppmann, H. Riegger, W.A. Kaysser, S. Smolej, S. Pejovnik: Z. Metallkd. 70 (1979) 707.Search in Google Scholar

[19] V. Smolej, S. Pejovnik, W.A. Kaysser: Powd. Met. Int. 14 (1982) 34.Search in Google Scholar

[20] P.M. Ossi, R. Roberti, G. Silva: Scripta Metall. 19 (1985) 569.10.1016/0036-9748(85)90339-4Search in Google Scholar

[21] In: Dan Zwillinger (Ed.), CRC Standard Mathematical Tables and Formulas, 30th Edition, CRC Press, Boca Raton (1995).Search in Google Scholar

[22] Z.S. Nikolic, in: Proceedings of the 6th International Conference on Fundamental and Applied Aspects of Physical Chemistry, Vol. II, Belgrade (2002) 502.Search in Google Scholar

[23] Z.S. Nikolic, in: Proceeding of the X WRTCS, Science of Sintering: Current Problems and New Trends, Serbian Academy of Sciences and Arts, Belgrade (2003) 13.Search in Google Scholar

[24] Z.S. Nikolic, G. Tomandl: 2nd International Conference on Materials Processing for Properties and Performance, Δ8–13-O09, Yokohama, Japan (2003) 256.Search in Google Scholar

[25] T.M. Shaw: J. Am. Ceram. Soc. 69 (1986) 27.10.1111/j.1151-2916.1986.tb04688.xSearch in Google Scholar

[26] Z.S. Nikolic, in: Proceedings of the 6th International Conference on Fundamental and Applied Aspects of Physical Chemistry, Vol. II, Belgrade (2002) 499.Search in Google Scholar
Received: 2004-01-12
Accepted: 2004-05-05
Published Online: 2022-01-26

© 2004 Carl Hanser Verlag, München

Articles in the same Issue

  1. Frontmatter
  2. Articles Basic
  3. Phase formation, thermal stability and crystallization behavior of Cu47Ti33Zr11Ni8X1 (X = Fe, Si, Sn, Pb) bulk glassy alloys
  4. Thermodynamic reassessment of the Al–V system
  5. Experimental investigation of the equilibrium composition of titanium carbonitride and analysis using thermodynamic modelling
  6. A model for 3-D study of rearrangement in liquid phase sintering
  7. Measurement and calculation of surface tension of undercooled liquid Fe-20 wt.% Cu alloy
  8. Phase equilibria in iron-rich Fe–Al–V ternary alloy system
  9. Articles Applied
  10. Evolution of microstructure during creep in gamma Ti–52Al at 1100 K and high applied stresses
  11. Effect of tempering on the chemical and phase composition of MxCy precipitates in low carbon chromium-molybdenum-vanadium steel
  12. Phase changes in superaustenitic steels after long-term annealing
  13. 3D and microstructural analysis of the chip formation during high speed cutting of C45E (AISI 1045)
  14. Elevated temperature friction and wear behavior of SiC-reinforced copper matrix composites
  15. On the microstructure developed in as-cast and homogenized 7010 aluminium alloy containing scandium
  16. Notifications/Mitteilungen
  17. Personal/Personelles
  18. Conferences/Konferenzen
https://doi.org/10.3139/ijmr-2004-0182
Keywords for this article
Liquid phase sintering; Rearrangement; Capillary force; Computer simulation

Articles in the same Issue

  1. Frontmatter
  2. Articles Basic
  3. Phase formation, thermal stability and crystallization behavior of Cu47Ti33Zr11Ni8X1 (X = Fe, Si, Sn, Pb) bulk glassy alloys
  4. Thermodynamic reassessment of the Al–V system
  5. Experimental investigation of the equilibrium composition of titanium carbonitride and analysis using thermodynamic modelling
  6. A model for 3-D study of rearrangement in liquid phase sintering
  7. Measurement and calculation of surface tension of undercooled liquid Fe-20 wt.% Cu alloy
  8. Phase equilibria in iron-rich Fe–Al–V ternary alloy system
  9. Articles Applied
  10. Evolution of microstructure during creep in gamma Ti–52Al at 1100 K and high applied stresses
  11. Effect of tempering on the chemical and phase composition of MxCy precipitates in low carbon chromium-molybdenum-vanadium steel
  12. Phase changes in superaustenitic steels after long-term annealing
  13. 3D and microstructural analysis of the chip formation during high speed cutting of C45E (AISI 1045)
  14. Elevated temperature friction and wear behavior of SiC-reinforced copper matrix composites
  15. On the microstructure developed in as-cast and homogenized 7010 aluminium alloy containing scandium
  16. Notifications/Mitteilungen
  17. Personal/Personelles
  18. Conferences/Konferenzen
Downloaded on 26.4.2026 from https://www.degruyterbrill.com/document/doi/10.3139/ijmr-2004-0182/html?lang=en
Scroll to top button