Startseite Automated dihedral angle measurement in liquid phase sintered alloys
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Automated dihedral angle measurement in liquid phase sintered alloys

  • P. Chhillar , S. Sangal und A. Upadhyaya EMAIL logo
Veröffentlicht/Copyright: 20. Dezember 2021
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 95 Heft 1

Abstract

The dihedral angle distribution is a useful parameter in the quantification of liquid-phase sintered alloys. Recently, Chhabra et al. have successfully developed a methodology based on digital image processing for dihedral-angle measurements on single-phase polycrystalline alloys. In this paper, the technique used by Chhabra et al. has been modified to evaluate dihedral angles of microstructures in a two-dimensional plane section of two-phase liquid-phase sintered alloys. It is shown that the procedure is extremely fast and accurate and, therefore, can be applied to obtain a significantly large statistical sample of dihedral angles. The validity of this method is demonstrated by evaluating the dihedral angles on samples of W–Ni–Cu alloys.

Keywords: Dihedral angle; Image processing; Bitmaps; Least-square polynomial fit; Neck points; Kernels; Correlation coefficient
Dr. Anish Upadhyaya, Materials and Metallurgical Engineering, IIT Kanpur 208016 (UP), India, Tel.: +512 597 640, Fax: +512 590 260

References

[1] R.M. German: Metall. Trans. A 16 (1985) 1247.10.1007/BF02670329Suche in Google Scholar

[2] A. Upadhyaya: Ph. D. Thesis, The Pennsylvania State University, University Park, PA (1998).Suche in Google Scholar

[3] A. Upadhyaya, R.M. German: Int. J. Powder Metall. 34 (1998) 43.Suche in Google Scholar

[4] J.L. Johnson, A. Upadhyaya, R.M. German: Metall. Mater. Trans. B 29 (1998) 857.10.1007/s11663-998-0145-4Suche in Google Scholar

[5] A. Upadhyaya, R.M. German: Metall. Mater. Trans. A 29 (1998) 2631.10.1007/s11661-998-0235-6Suche in Google Scholar

[6] O.K. Riegger, L.H. Van-Vlack: Trans. AIME 218 (1960) 933.Suche in Google Scholar

[7] R.T. DeHoff: Metallography 19 (1986) 209.10.1016/0026-0800(86)90036-4Suche in Google Scholar

[8] S. Chhabra, P. Chhillar, S. Sangal: Pract. Metallogr. 40 (2003) 85.Suche in Google Scholar

[9] K. Chattopadhyay: M. Tech Thesis, Indian Institute of Technology, Kanpur, India, (2003).Suche in Google Scholar

[10] P. Chhillar, K. Chattopadhyay, P. Mishra, A. Upadhyaya, S. Sangal: Trans. PMAI 29 (2003) (in press).Suche in Google Scholar

[11] A.K. Jain: Digital Image Processing Fundamentals, Prentice Hall, New Delhi, India (1989).Suche in Google Scholar
Received: 2003-07-09
Published Online: 2021-12-20

© 2004 Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Frontmatter
  2. Editorial
  3. Editorial
  4. Articles AApplied
  5. Automated dihedral angle measurement in liquid phase sintered alloys
  6. Computer-aided analysis of repair welding of stamping tools
  7. Influence of retrogression and re-ageing on the mechanical and corrosion properties of 7039 aluminium alloy
  8. On the occurrence of Z-phase in a creep-tested 10 % Cr steel
  9. Superplasticity in a directionally solidified multiphase Ni-25Al-25Cr alloy
  10. Articles BBasic
  11. Assessment of thermodynamic parameters in the system ZrO2–Y2O3–Al2O3
  12. Assessment of the thermodynamics and phase diagram of the SrO–B2O3 system
  13. Thermodynamic description of the Au–Al system
  14. Chemical reaction and stability of Ti3SiC2 in Cu during high-temperature processing of Cu/Ti3SiC2 composites
  15. Precipitation behavior of an Fe-1.03 wt.% Cu alloy
  16. Instructions to Authors/Richtlinien für Autoren
  17. Instructions for Authors
  18. Notifications/Mitteilungen
  19. Personal/Personelles
  20. Press/Presse
  21. Books/Bücher
  22. Events/Veranstaltungen
https://doi.org/10.3139/ijmr-2004-0002
Schlagwörter für diesen Artikel
Dihedral angle; Image processing; Bitmaps; Least-square polynomial fit; Neck points; Kernels; Correlation coefficient

Artikel in diesem Heft

  1. Frontmatter
  2. Editorial
  3. Editorial
  4. Articles AApplied
  5. Automated dihedral angle measurement in liquid phase sintered alloys
  6. Computer-aided analysis of repair welding of stamping tools
  7. Influence of retrogression and re-ageing on the mechanical and corrosion properties of 7039 aluminium alloy
  8. On the occurrence of Z-phase in a creep-tested 10 % Cr steel
  9. Superplasticity in a directionally solidified multiphase Ni-25Al-25Cr alloy
  10. Articles BBasic
  11. Assessment of thermodynamic parameters in the system ZrO2–Y2O3–Al2O3
  12. Assessment of the thermodynamics and phase diagram of the SrO–B2O3 system
  13. Thermodynamic description of the Au–Al system
  14. Chemical reaction and stability of Ti3SiC2 in Cu during high-temperature processing of Cu/Ti3SiC2 composites
  15. Precipitation behavior of an Fe-1.03 wt.% Cu alloy
  16. Instructions to Authors/Richtlinien für Autoren
  17. Instructions for Authors
  18. Notifications/Mitteilungen
  19. Personal/Personelles
  20. Press/Presse
  21. Books/Bücher
  22. Events/Veranstaltungen
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 16.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/ijmr-2004-0002/pdf
Button zum nach oben scrollen