Startseite Influence of Processing Temperature on the Morphological and Mechanical Properties of a PC/TLCP Blend
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Influence of Processing Temperature on the Morphological and Mechanical Properties of a PC/TLCP Blend

  • H. Wang und G. Hinrichsen
Veröffentlicht/Copyright: 3. Juni 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
International Polymer Processing
Aus der Zeitschrift International Polymer Processing Band 12 Heft 1

Abstract

The influence of processing temperature on the morphological and mechanical properties of polycarbonate (PC) blended with a thermotropic liquid crystalline polymer (TLCP) has been studied. At a barrel temperature of 310°C, the TLCP of the blends exhibits the high orientation level and fiber alignment which correspond to maximum tensile strength. This indicates that the processing temperature might result in the change of the viscosity ratios of the dispersed and continuous phase and is one of the main processing parameters.

*

On leave of Zhejiang University, Department of Polymer Science and Engineering, Hangzhou 310027, P.R. China

** Mail address: Professor Dr. G. Hinrichsen, Institute of Non-metallic Materials, Technical University Berlin, Englische Str. 20, 10587 Berlin, Germany
Received: 1996-2-14
Accepted: 1996-8-16
Published Online: 2013-06-03
Published in Print: 1997-03-01

© 1997, Carl Hanser Verlag, Munich

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial
  5. Screw Extrusion
  6. Upgrading Recycled HDPE by Rheometer-Controlled Crosslinking
  7. Blend Morphology of Linear Low Density Polyethylene and Polystyrene in a Non-Intermeshing Twin Screw Extruder
  8. Mixing
  9. A Study on the Reactive Compatibilization of a PBT/LCP Blend: Catalyst Effect
  10. Influence of Processing Temperature on the Morphological and Mechanical Properties of a PC/TLCP Blend
  11. Fibers
  12. The Effect of Drawing and Annealing Conditions on the Structure and Properties of Bacterial Poly(3-hydroxybutyrate-co-3 hydroxyvalerate) Fibers
  13. Numerical Analysis of Cooling Air Systems in Film Blowing
  14. Moulding
  15. On the Simulation of Thermoplastic Injection Moulding Process
  16. Molding
  17. Rheology of Layered Thermoplastic Matrix Composites during Compression Molding
  18. Studies of the Trans-Quinacridone Nucleation of Poly-(ethylene-b-propylene)
  19. The Role of Long Molecules and Nucleating Agents in Shear Induced Crystallization of Isotactic Polypropylenes**
https://doi.org/10.3139/217.970026

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial
  5. Screw Extrusion
  6. Upgrading Recycled HDPE by Rheometer-Controlled Crosslinking
  7. Blend Morphology of Linear Low Density Polyethylene and Polystyrene in a Non-Intermeshing Twin Screw Extruder
  8. Mixing
  9. A Study on the Reactive Compatibilization of a PBT/LCP Blend: Catalyst Effect
  10. Influence of Processing Temperature on the Morphological and Mechanical Properties of a PC/TLCP Blend
  11. Fibers
  12. The Effect of Drawing and Annealing Conditions on the Structure and Properties of Bacterial Poly(3-hydroxybutyrate-co-3 hydroxyvalerate) Fibers
  13. Numerical Analysis of Cooling Air Systems in Film Blowing
  14. Moulding
  15. On the Simulation of Thermoplastic Injection Moulding Process
  16. Molding
  17. Rheology of Layered Thermoplastic Matrix Composites during Compression Molding
  18. Studies of the Trans-Quinacridone Nucleation of Poly-(ethylene-b-propylene)
  19. The Role of Long Molecules and Nucleating Agents in Shear Induced Crystallization of Isotactic Polypropylenes**
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 6.9.2025 von https://www.degruyterbrill.com/document/doi/10.3139/217.970026/html
Button zum nach oben scrollen