Skip to main content
Article
Licensed
Unlicensed Requires Authentication

Conveying and Melting in Screw Extruders with Axial Screw Movement

Published/Copyright: May 27, 2013
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Polymer Processing
From the journal International Polymer Processing Volume 7 Issue 1

Abstract

Reciprocating extruders are used in injection molding. The number of reciprocating extruders used in the plastics processing industry is larger than conventional extruders. Therefore it is surprising that only few studies have been made of the conveying and melting process in reciprocating extruders.

* Mail address: Dr. Chris Rauwendaal, Rauwendaal Extrusion Engineering, Inc., 12693 Roble Veneno Lane, Los Altos Hills, CA 94022-2619, U.S.A.
Received: 1991-3-28
Accepted: 1991-5-16
Published Online: 2013-05-27
Published in Print: 1992-03-01

© 1992, Carl Hanser Verlag, Munich

Articles in the same Issue

  1. Contents
  2. Contents
  3. Internal and Continuous Mixers
  4. Model Development for an Internal Mixer
  5. Simulation of Flow in a Farrel Continuous Mixer
  6. Extrusion
  7. Influence of Process Data on the Throughput of Large Extruders within the Range of 600 to 6 000 kg/h
  8. Conveying and Melting in Screw Extruders with Axial Screw Movement
  9. Thermo-viscous Effects in Extrusion of Planar Jets with Solidification
  10. Film
  11. Dynamics and Stability of Double Bubble Tubular Film Extrusion
  12. Melt Strength Behavior of Polyethylene Blends**
  13. Optical Properties and Orientation Development in Uniaxially Stretched Syndiotactic Polystyrene from Amorphous Precursors
  14. Molding
  15. Thermoviscoelastic Calculation of Residual Stresses and Residual Shapes of Injection Molded Parts**
  16. Analysis and Simulation of Structural Reaction Injection Molding (SRIM)
  17. Crystal Orientation in Injection Moldings of Flaky Filler-Filled Polypropylenes
  18. Erratum
  19. Molecular Orientation in Injection-molded Polypropylene Copolymers with Ethylene
https://doi.org/10.3139/217.920026

Articles in the same Issue

  1. Contents
  2. Contents
  3. Internal and Continuous Mixers
  4. Model Development for an Internal Mixer
  5. Simulation of Flow in a Farrel Continuous Mixer
  6. Extrusion
  7. Influence of Process Data on the Throughput of Large Extruders within the Range of 600 to 6 000 kg/h
  8. Conveying and Melting in Screw Extruders with Axial Screw Movement
  9. Thermo-viscous Effects in Extrusion of Planar Jets with Solidification
  10. Film
  11. Dynamics and Stability of Double Bubble Tubular Film Extrusion
  12. Melt Strength Behavior of Polyethylene Blends**
  13. Optical Properties and Orientation Development in Uniaxially Stretched Syndiotactic Polystyrene from Amorphous Precursors
  14. Molding
  15. Thermoviscoelastic Calculation of Residual Stresses and Residual Shapes of Injection Molded Parts**
  16. Analysis and Simulation of Structural Reaction Injection Molding (SRIM)
  17. Crystal Orientation in Injection Moldings of Flaky Filler-Filled Polypropylenes
  18. Erratum
  19. Molecular Orientation in Injection-molded Polypropylene Copolymers with Ethylene
Downloaded on 18.4.2026 from https://www.degruyterbrill.com/document/doi/10.3139/217.920026/html
Scroll to top button