Process Simulation-Based Design, Mold Construction and Mechanical Performance Evaluation of an Insert-Injection Molded Thermoplastic Polyurethane Part

References

Bayer MaterialScience, “Part and Mold Design – A Design Guide”, Bayer Corporation, Company Broschure174 (2000), http://www.bayer.com/polymers-usaSuche in Google Scholar

Chen, X., Lam, Y. C. and Li, D. Q., “Analysis of Thermal Residual Stress in Plastic Injection Molding”, J. Mater. Process. Technol., 101, 275–80 (2000) 10.1016/S0924-0136(00)00472-6Suche in Google Scholar

Farnam, S. M., Rezaie, F., “Simulation of Crack Propagation in Prestressed Concrete Sleepers by Fracture Mechanics”, Eng. Fail. Anal., 96, 109–117 (2019) 10.1016/j.engfailanal.2018.09.012Suche in Google Scholar

Fetecau, C., Dobrea, D. V. and Postolache, I., “Overmolding Injection Molding Simulation of Tensile Test Specimen”, International Journal of Modern Manufacturing Technologies, 2, 45–50 (2010)Suche in Google Scholar

GLS Corporation, “GLS Overmolding Guide”, 1 (852):18 (2004)Suche in Google Scholar

Harper, C. A., “Handbook of Plastics Technologies (Book Review)”, IEEE Electrical Insulation Magazine, 22, 53 (2006) 10.1109/MEI.2006.253437Suche in Google Scholar

Park, H.-S., Dang, X.-P., “Design and Simulation-Based Optimization of Cooling Channels for Plastic Injection Mold”, in New Technologies – Trends, Innovations and Research, Volosencu, C. (Ed.), Intech Open, p. 19–44 (2012) 10.5772/32730Suche in Google Scholar

Honkanen, M., Hoikkanen, M., Vippola, M., Vuorinen, J. and Lepistö, T., “Metal-Plastic Adhesion in Injection-Molded Hybrids”, J. Adhes. Sci. Technol., 23, 1747–1761 (2009) 10.1163/016942409X12489445844435Suche in Google Scholar

Huang, X. Y., Li, D. Q. and Xu, Q., 2008 “Gate Location Optimization in Injection Molding Based on Empirical Search Method”, Mater. Sci. Forum, 575–578, 55–62 (2008) 10.4028/www.scientific.net/msf.575-578.55Suche in Google Scholar

Jin, K., Jeong, T., Kim, T., Kim, N. and Kim, B., “Analysis and Design for Reducing Residual Stress and Distortion after Ejection of Injection Molded Part with Metal-Insert”, Int. J. Precis. Eng. Manuf., 15, 2533–2542 (2014) 10.1007/s12541-014-0624-2Suche in Google Scholar

Jones, P.: The Mould Design Guide, Volume 53, Smithers Rapra Technology Limited Shawbury, Shrewsbury, Shropshire, UK (2010)Suche in Google Scholar

Milner, D. A., Vaciliou, V.C.: ComputerAided Engineering for Manufacture, Springer, USA (1986) 10.1007/978-1-4684-6912-7Suche in Google Scholar

Pandelidis, I., Zou, Q., “Optimization of Injection Molding Design. Part I: Gate Location Optimization”, Polym. Eng. Sci., 30, 873–882 (1990) 10.1002/pen.760301502Suche in Google Scholar

Qi, H. J., Boyce, M. C., 2005 “Stress-Strain Behavior of Thermoplastic Polyurethanes”, Mech. Mater., 37, 817–839 (2005) 10.1016/j.mechmat.2004.08.001Suche in Google Scholar

Quintana, M. C, Rueda, F. and Frontini, P., “Three-Dimensional Simulation of a Thermoplastic Polyurethane Injection Molding with a Metallic Insert: Gate Location and Cooling System Optimization”, Proceedings of the 7th International Conference on Mechanics and Materials in Design, Algarve, Portugal, (M2D2017), 111–112 (2017)Suche in Google Scholar

Ramani, K., Moriarty, B., 199 “Thermoplastic Bonding to Metals via Injection Molding for Macro-Composite Manufacture”, Polym. Eng. Sci., 38, 870–877 (19998) 10.1002/pen.10253Suche in Google Scholar

Rezayat, M., Jantzen, B., “Effects of Inserts on the Injection Molding Process”, Polym. Eng. Sci., 35, 247–251 (1995) 10.1002/pen.760350305Suche in Google Scholar

Sadeghi, J., Barati, P., “Comparisons of the Mechanical Properties of Timber, Steel and Concrete Sleepers”, Struct. Infrastruct. Eng., 8, 1151–1159 (2012) 10.1080/15732479.2010.507706Suche in Google Scholar

Stan, D., Tulcan, A., Tulcan, L. and Iclanzan, T., “Influence Factors on the Dimensional Accuracy of the Plastic Parts”, Materiale Plastice, 45, 119–124 (2008)Suche in Google Scholar

Technology, Railway, Web Article, https://www.Railway-Technology.Com/Features/Feature92105/.htlm (2010)Suche in Google Scholar

Yadegari, M., Masoumi, H. and Gheisari, M., “Optimization of Cooling Channels in Plastic Injection Molding”, Int. J. Appl. Eng. Res., 11, 5777–5780 (2016)Suche in Google Scholar

Yu, C. J., Sunderland, J. E. and Poli, C., “Thermal Contact Resistance in Injection Molding”, Polym. Eng. Sci., 30, 1599–1606 (1990) 10.1002/pen.760302408Suche in Google Scholar