Article Open Access

The Influence of Mechanical Recycling on Properties in Injection Molding of Fiber-Reinforced Polypropylene

  • , , , , and
Published/Copyright: August 1, 2019
Download Article (PDF)
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Polymer Processing
From the journal International Polymer Processing Volume 34 Issue 4

Received: 2018-10-04
Accepted: 2019-02-15
Published Online: 2019-08-01
Published in Print: 2019-08-13

© 2019, Carl Hanser Verlag, Munich

Articles in the same Issue

  1. Contents
  2. Contents
  3. Regular Contributed Articles
  4. Influence of Post-Treatment Media on Morphological Changes in Transient Macromolecules of Polymeric Fibers
  5. The Influence of Mechanical Recycling on Properties in Injection Molding of Fiber-Reinforced Polypropylene
  6. Study on Influence of Co-Injection Molding Process on Self-Reinforcing Characteristics of Self-Reinforced Polypropylene Composite via Visualization
  7. Influence of Ultrasonic Transducer Structural Parameters on the Frictional Plasticizing Heat Generation of Polymer Particles
  8. Influence of the Mold Temperature and Part Thickness on the Replication Quality and Molecular Orientation in Compression Injection Molding of Polystyrene
  9. Study of Bonding Formation between the Filaments of PLA in FFF Process
  10. Rheology and Extrusion Foaming of Partially Crosslinked Thermoplastic Vulcanizates Silicone
  11. Influence of Rubber Ratio and Crosslinking Agent on Mechanical Properties, Crystallization and Rheological Behaviors of EPDM/PP Thermoplastic Elastomer
  12. Effect of Annealing Temperature on PP Microporous Membranes Obtained by a Melt-Extrusion-Stretching Method
  13. PPS News
  14. PPS News
  15. Seikei Kakou Abstracts
  16. Seikei-Kakou Abstracts
https://doi.org/10.3139/217.3770
Creative Commons
BY 4.0

Articles in the same Issue

  1. Contents
  2. Contents
  3. Regular Contributed Articles
  4. Influence of Post-Treatment Media on Morphological Changes in Transient Macromolecules of Polymeric Fibers
  5. The Influence of Mechanical Recycling on Properties in Injection Molding of Fiber-Reinforced Polypropylene
  6. Study on Influence of Co-Injection Molding Process on Self-Reinforcing Characteristics of Self-Reinforced Polypropylene Composite via Visualization
  7. Influence of Ultrasonic Transducer Structural Parameters on the Frictional Plasticizing Heat Generation of Polymer Particles
  8. Influence of the Mold Temperature and Part Thickness on the Replication Quality and Molecular Orientation in Compression Injection Molding of Polystyrene
  9. Study of Bonding Formation between the Filaments of PLA in FFF Process
  10. Rheology and Extrusion Foaming of Partially Crosslinked Thermoplastic Vulcanizates Silicone
  11. Influence of Rubber Ratio and Crosslinking Agent on Mechanical Properties, Crystallization and Rheological Behaviors of EPDM/PP Thermoplastic Elastomer
  12. Effect of Annealing Temperature on PP Microporous Membranes Obtained by a Melt-Extrusion-Stretching Method
  13. PPS News
  14. PPS News
  15. Seikei Kakou Abstracts
  16. Seikei-Kakou Abstracts
Downloaded on 14.4.2026 from https://www.degruyterbrill.com/document/doi/10.3139/217.3770/html
Scroll to top button