Article
Licensed
Unlicensed Requires Authentication

PPS News

Published/Copyright: November 29, 2017
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Polymer Processing
From the journal International Polymer Processing Volume 32 Issue 5

Published Online: 2017-11-29
Published in Print: 2017-11-17

© 2017, Carl Hanser Verlag, Munich

Articles in the same Issue

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial
  5. Special Issue Contributions – Review Article
  6. Process Induced Defects in Liquid Molding Processes of Composites
  7. Special Issue Contributions
  8. Crystallization of Polymers in Processing Conditions: An Overview
  9. Modelling of the Plastisol Knife Over Roll Coating Process
  10. Low Density Polypropylene/Waste Cellulose Fiber Composites by High-Shear Thermo-Kinetic Mixer
  11. Evaluation of Structures and Morphologies of Recycled PC/PET Blends Fabricated by High-Shear Kneading Processing
  12. Transient Swell of a High Density Polyethylene Using Adjustable Gap Slit Die
  13. Effect of Solvent Volatility on Diameter Selection of Bicomponent Nanofibers Produced by Gas Jet Fiber Process Test
  14. Flow and Thermal History Effects on Morphology and Tensile Behavior of Poly(oxymethylene) Micro Injection Molded Parts
  15. Tailoring Heat-Seal Properties of Biodegradable Polymers through Melt Blending
  16. Development of Dispersion during Compounding and Extrusion of Polypropylene/Graphite Nanoplates Composites
  17. The Grafting of PE-g-MA Chains on Graphene Derivatives to Improve Tensile Properties of Polyethylene
  18. High-Pressure Preform Foam Blow Molding
  19. Fluid Elasticity in Plastic Pipe Extrusion: Loads on Die Barrel
  20. Rheological In-Mold Measurements and Characterizations of Sheet-Molding-Compound (SMC) Formulations with Different Constitution Properties by Using a Compressible Shell Model
  21. PPS News
  22. PPS News
  23. Seikei Kakou Abstracts
  24. Seikei-Kakou Abstracts
https://doi.org/10.3139/217.017054

Articles in the same Issue

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial
  5. Special Issue Contributions – Review Article
  6. Process Induced Defects in Liquid Molding Processes of Composites
  7. Special Issue Contributions
  8. Crystallization of Polymers in Processing Conditions: An Overview
  9. Modelling of the Plastisol Knife Over Roll Coating Process
  10. Low Density Polypropylene/Waste Cellulose Fiber Composites by High-Shear Thermo-Kinetic Mixer
  11. Evaluation of Structures and Morphologies of Recycled PC/PET Blends Fabricated by High-Shear Kneading Processing
  12. Transient Swell of a High Density Polyethylene Using Adjustable Gap Slit Die
  13. Effect of Solvent Volatility on Diameter Selection of Bicomponent Nanofibers Produced by Gas Jet Fiber Process Test
  14. Flow and Thermal History Effects on Morphology and Tensile Behavior of Poly(oxymethylene) Micro Injection Molded Parts
  15. Tailoring Heat-Seal Properties of Biodegradable Polymers through Melt Blending
  16. Development of Dispersion during Compounding and Extrusion of Polypropylene/Graphite Nanoplates Composites
  17. The Grafting of PE-g-MA Chains on Graphene Derivatives to Improve Tensile Properties of Polyethylene
  18. High-Pressure Preform Foam Blow Molding
  19. Fluid Elasticity in Plastic Pipe Extrusion: Loads on Die Barrel
  20. Rheological In-Mold Measurements and Characterizations of Sheet-Molding-Compound (SMC) Formulations with Different Constitution Properties by Using a Compressible Shell Model
  21. PPS News
  22. PPS News
  23. Seikei Kakou Abstracts
  24. Seikei-Kakou Abstracts
Downloaded on 13.4.2026 from https://www.degruyterbrill.com/document/doi/10.3139/217.017054/html
Scroll to top button