Article
Licensed
Unlicensed
Requires Authentication
PPS News
Published/Copyright:
November 4, 2014
Published Online: 2014-11-04
Published in Print: 2014-11-30
© 2014, Carl Hanser Verlag, Munich
You are currently not able to access this content.
You are currently not able to access this content.
Articles in the same Issue
- Contents
- Contents
- Regular Contributed Articles
- Converging-Diverging Flow in a Novel Extruder and its Application in Film Blowing
- Modeling of Plasticating Injection Molding – Experimental Assessment
- Viscosity Analysis of a Polymer-Based Drug Delivery System Using Open-Source CFD Methods and High-Pressure Capillary Rheometry
- Thermal Properties and Morphology Characteristics of a PP Mono-Filament and its Foam
- Thermal and Tensile Behavior of HD-PE Films Containing Iron (III) Acetylacetonate after UV Irradiation
- Carbon Black Reinforced Thermoplastic Vulcanizates Based on High Impact Polystyrene/Styrene-Butadiene-Styrene Block Copolymer/Styrene-Butadiene Rubber Blends
- A Study of the Bubbles in UV Micro Roll-to-Roll Imprinting
- An Annular Rotating-Die Technique in Extrusion Process: Effect of Mandrel Rotating Speed on Extrudate Swell Behavior of HDPE Parison
- Investigation of the Structural Robustness of Deep Depth Injection Mold with Cavity Pressure and Mold Design
- Verifying the Melting Behavior in Single-Screw Plasticization Units Using a Novel Simulation Model and Experimental Method
- Processing of Polyetherimide/Cloisite 30B Nanocomposite by Vibration Casting Method
- Comparison between 1D and 3D Approaches for Twin-Screw Extrusion Simulation
- Study on the Polymer Melt Flow in a Closely Intermeshing Counter-Rotating Twin Screw Extruder
- The Influence of Moisture and Laminate Setup on the De-Consolidation Behavior of PA6/GF Thermoplastic Matrix Composites
- PPS News
- PPS News
- Seikei Kakou Abstracts
- Seikei Kakou Abstracts
Articles in the same Issue
- Contents
- Contents
- Regular Contributed Articles
- Converging-Diverging Flow in a Novel Extruder and its Application in Film Blowing
- Modeling of Plasticating Injection Molding – Experimental Assessment
- Viscosity Analysis of a Polymer-Based Drug Delivery System Using Open-Source CFD Methods and High-Pressure Capillary Rheometry
- Thermal Properties and Morphology Characteristics of a PP Mono-Filament and its Foam
- Thermal and Tensile Behavior of HD-PE Films Containing Iron (III) Acetylacetonate after UV Irradiation
- Carbon Black Reinforced Thermoplastic Vulcanizates Based on High Impact Polystyrene/Styrene-Butadiene-Styrene Block Copolymer/Styrene-Butadiene Rubber Blends
- A Study of the Bubbles in UV Micro Roll-to-Roll Imprinting
- An Annular Rotating-Die Technique in Extrusion Process: Effect of Mandrel Rotating Speed on Extrudate Swell Behavior of HDPE Parison
- Investigation of the Structural Robustness of Deep Depth Injection Mold with Cavity Pressure and Mold Design
- Verifying the Melting Behavior in Single-Screw Plasticization Units Using a Novel Simulation Model and Experimental Method
- Processing of Polyetherimide/Cloisite 30B Nanocomposite by Vibration Casting Method
- Comparison between 1D and 3D Approaches for Twin-Screw Extrusion Simulation
- Study on the Polymer Melt Flow in a Closely Intermeshing Counter-Rotating Twin Screw Extruder
- The Influence of Moisture and Laminate Setup on the De-Consolidation Behavior of PA6/GF Thermoplastic Matrix Composites
- PPS News
- PPS News
- Seikei Kakou Abstracts
- Seikei Kakou Abstracts
