Metallurgical Failure Investigation of SCC in Leaking Piping System in a Combined Cycle Gas Turbine Power Plant
-
A. Neidel
Abstract
Cracking and leakage, not repairable by welding, was found in premix piping of heavy-duty gas turbine engine for power plant applications. The subject laboratory specimen, a pipe section cut out on site and received at the investigating laboratory, failed by transgranular stress corrosion cracking (SCC). The stress corrosion cracking has probably been induced by chlorides (halide-induced stress corrosion cracking). Chlorine peaks were found in EDS spectra acquired on the inner pipe wall surfaces. However, it cannot completely be ruled out that those were artifacts caused by handling, cleaning, and cutting. The cracking is located adjacent to welds.
Kurzfassung
In Vormischrohrleitungen einer in einem Kraftwerk zum Einsatz kommenden Großgasturbine wurden durch Schweißarbeiten nicht reparierbare Risse und eine Leckage entdeckt. Die entsprechende Laborprobe, ein vor Ort abgetrennter und im Untersuchungslabor eingegangener Rohrabschnitt, versagte aufgrund transkristalliner Spannungsrisskorrosion (SpRK). Die Spanungsrisskorrosion ist vermutlich auf Chloride zurückzuführen (halogenidinduzierte Spannungsrisskorrosion). In von den Oberflächen der Rohrinnenwand aufgenommenen EDX-Spektren sind Chlor-Peaks auszumachen. Es kann nicht ausgeschlossen werden, dass es sich hierbei um Artefakte handelt, die von der Handhabung, dem Reinigen oder dem Trennen stammen. Die Risse bildeten sich in der Nähe von Schweißnähten.
References / Literatur
[1] https://www.siemens.com/innovation/en/home/pictures-of-the-future/energy-and-efficiency/sustainable-power-generation-the-worlds-most-efficient-combined-cycle-power-plant-goes-online-in-2016.htmlSuche in Google Scholar
[2] Seume, J.; Lechner, C. (Ed.): Stationäre Gasturbinen, Springer-Verlag, Berlin, Heidelberg, 200310.1007/978-3-662-10016-5Suche in Google Scholar
[3] Neidel, A.; Ullrich, T.; Fischer, B.: Internal report GT BLN QM / 2011 / 0710g_revSuche in Google Scholar
[4] van Buer, R.: Internal memo, November 14, 2011Suche in Google Scholar
[5] van Buer, R.: Internal memo, November 21, 2011Suche in Google Scholar
[6] DGTLV-411615001, Index A : October 2007, internal purchasing specification of engine manufacturerSuche in Google Scholar
[7] Generic Welding Procedure Specification WPS OE1-2007-447, Index 0: September 27, 2007, internal welding specification of engine manufacturerSuche in Google Scholar
[8] TÜV Nord Systems GmbH & Co. KG, report 1424/668640800/2011Suche in Google Scholar
[9] Lange, G. (Hrsg.): Systematische Beurteilung technischer Schadensfälle. 3. Auflage, DGM, 1992Suche in Google Scholar
[10] Grosch, J.: Schadenskunde im Maschinenbau. 4. Auflage, Expert Verlag, 2004Suche in Google Scholar
[11] ASM Handbook, Volume 11: Failure Analysis and Prevention. 6. Auflage, ASM International, 1998Suche in Google Scholar
[12] VDI-Richtlinie 3822, Part 3: March 2007: Failure analysis – Failures caused by corrosion in electrolytes. Beuth-Verlag GmbH, Berlin, Düsseldorf2007Suche in Google Scholar
[13] Neidel, A. (Ed.): Handbuch Metallschäden. 1. Auflage, Hanser-Verlag, München201010.3139/9783446429666.001Suche in Google Scholar
© 2019, Carl Hanser Verlag, München
Artikel in diesem Heft
- Contents/Inhalt
- Contents
- Editorial
- Editorial
- Technical Contributions/Fachbeiträge
- In-Service Microstructural Modifications caused by Fatigue Phenomena leading to the Failure of a High-Voltage Cable
- Preparation Methods for Scanning Electron Microscope Characterization of Nano-Carbides in Cold Work Steel X153CrMoV12
- Development of Second-Phase Particles during Solidification and Homogenization of Aluminium Alloy AlMn1
- Metallurgical Failure Investigation of SCC in Leaking Piping System in a Combined Cycle Gas Turbine Power Plant
- Meeting Diary/Veranstaltungskalender
- Meeting Diary
Artikel in diesem Heft
- Contents/Inhalt
- Contents
- Editorial
- Editorial
- Technical Contributions/Fachbeiträge
- In-Service Microstructural Modifications caused by Fatigue Phenomena leading to the Failure of a High-Voltage Cable
- Preparation Methods for Scanning Electron Microscope Characterization of Nano-Carbides in Cold Work Steel X153CrMoV12
- Development of Second-Phase Particles during Solidification and Homogenization of Aluminium Alloy AlMn1
- Metallurgical Failure Investigation of SCC in Leaking Piping System in a Combined Cycle Gas Turbine Power Plant
- Meeting Diary/Veranstaltungskalender
- Meeting Diary
