Home Ablation and mechanical investigation of carbon/rubber woven laminates for ultrahigh temperature applications
Article
Licensed
Unlicensed Requires Authentication

Ablation and mechanical investigation of carbon/rubber woven laminates for ultrahigh temperature applications

  • Yanhui Liu , Chao Ma , Jingyu Su , Yong Li and Zhengshuai Yin
Published/Copyright: July 4, 2018
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 109 Issue 7

Abstract

A novel needled carbon/rubber woven laminate was fabricated using heat vulcanizing silicone rubber and polyarylacetylene (PAA) as the matrix and two-dimensional carbon fiber (TCF) woven fabrics as the reinforcement phase. The tensile strength and hardness of the laminates were increased with the increasing of the content of PAA due to better compatibility between PAA and TCF. Ablation testing results demonstrated that the ablation rate firstly deceased and then increased with increasing of PAA content due to charring action of PAA and the formation of a loose ablation layer with cracks.

Keywords: Silicone rubber; Polyarylacetylene; Laminated structure; Carbon fiber woven fabrics
*Correspondence address, Dr. Yanhui Liu, School of Material Science and Engineering, Shenyang, Ligong University, 110159 Shenyang, Liaoning, P.R. China, Tel.: +862424680841, E-mail:

References

[1] Y.Liu, J.Su, Z.Yin, Y.Li, Y.Zhi, J.Gao: J. Polym. Eng.37 (2017) 521. 10.1515/polyeng-2016-0130Search in Google Scholar

[2] Y.Liu, C.Ma, Y.Li, Z.Yin, Y.Zhi, J.Gao: Plast. Rubber. Compos.45 (2016) 430. 10.1080/14658011.2016.1243507Search in Google Scholar

[3] H.Fu, C.Ma, N.Kuang, S.Luan: J. Aeronaut.20 (2007) 124. 10.1016/s1000-9361(07)60018-1Search in Google Scholar

[4] W.Tseng, Y.Chen, G.Chang: Polym. Degrad. Stab.94 (2009) 2149. 10.1016/j.polymdegradstab.2009.09.008Search in Google Scholar

[5] T.B.Caston, A.R.Murphy, T.A.L.Harris: J. Power Sources196 (2011) 709. 10.1016/j.jpowsour.2010.07.057Search in Google Scholar

[6] D.Yang, W.Zhan, B.Jiang, Y.Guo: Composites Part A44 (2013) 70. 10.1016/j.compositesa.2012.09.002Search in Google Scholar

[7] C.Xuan, L.long: Mater. Sci. Eng. A528 (2011) 6998. 10.1016/j.msea.2011.05.053Search in Google Scholar

[8] L.Liu, Y.J.Song, Z.X.JiangX.Z.Zhang, L.N.Wu, Y.D.Huang: Appl. Surf. Sci.254 (2008) 5342. 10.1016/j.apsusc.2008.02.078Search in Google Scholar

Received: 2017-09-28
Accepted: 2018-02-05
Published Online: 2018-07-04
Published in Print: 2018-07-12

© 2018, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Influence of dislocations on precipitation processes in hot-extruded Al–Mn–Sc–Zr alloy
  5. Grain size gradient naturally prepared through recrystallization in rapidly solidified undercooled alloy melts
  6. Solidification behavior and microstructural characterization of Ni–Fe–W and Ni–Fe–W–Co matrix alloys
  7. Formation of amorphous interfacial layer between Zn-based alloy and SiC particles under ultrasonic-assisted brazing
  8. Microstructures and biocorrosion properties of biodegradable Mg–Zn–Y–Ca–xZr alloys
  9. Oxidation resistance and wettability of graphite/SiC composite
  10. Freeze linings in the Al2O3–CaO–SiO2 system
  11. Tribological properties of diamond-like carbon films deposited by vacuum arc
  12. Review
  13. Synthesis and characterization of magnesium-based hybrid composites – A review
  14. Short Communications
  15. Ablation and mechanical investigation of carbon/rubber woven laminates for ultrahigh temperature applications
  16. Effect of h-BN@Al2O3 on the microstructure and mechanical properties of Si3N4/TiC ceramic composite
  17. DGM News
  18. DGM News
https://doi.org/10.3139/146.111649
Keywords for this article
Silicone rubber; Polyarylacetylene; Laminated structure; Carbon fiber woven fabrics

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Influence of dislocations on precipitation processes in hot-extruded Al–Mn–Sc–Zr alloy
  5. Grain size gradient naturally prepared through recrystallization in rapidly solidified undercooled alloy melts
  6. Solidification behavior and microstructural characterization of Ni–Fe–W and Ni–Fe–W–Co matrix alloys
  7. Formation of amorphous interfacial layer between Zn-based alloy and SiC particles under ultrasonic-assisted brazing
  8. Microstructures and biocorrosion properties of biodegradable Mg–Zn–Y–Ca–xZr alloys
  9. Oxidation resistance and wettability of graphite/SiC composite
  10. Freeze linings in the Al2O3–CaO–SiO2 system
  11. Tribological properties of diamond-like carbon films deposited by vacuum arc
  12. Review
  13. Synthesis and characterization of magnesium-based hybrid composites – A review
  14. Short Communications
  15. Ablation and mechanical investigation of carbon/rubber woven laminates for ultrahigh temperature applications
  16. Effect of h-BN@Al2O3 on the microstructure and mechanical properties of Si3N4/TiC ceramic composite
  17. DGM News
  18. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 25.10.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.111649/html
Scroll to top button