Startseite Investigation of the surface residual stresses in spray cooled induction hardened gearwheels
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Investigation of the surface residual stresses in spray cooled induction hardened gearwheels

  • Dmytro Rodman , Christian Krause , Florian Nürnberger , Friedrich-Wilhelm Bach , Lorenz Gerdes und Bernd Breidenstein
Veröffentlicht/Copyright: 11. Juni 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 103 Heft 1

Abstract

The objective of the current investigation consists of testing the interchangeability of polymer solutions used during induction hardening with water – air spraying regarding compressive residual stresses. Gearwheels made of 42CrMo4 steel were induction hardened and subsequently quenched using water–air spray cooling. The effect of different cooling parameters on the surface's residual stresses in the gearwheel's tooth flanks was analysed by means of X-ray diffraction. The microstructure was characterised by means of hardness measurements and light-microscopy. Residual stresses could be specified after using water – air spray cooling and are comparable to those using polymer quenching. Quench parameters leading to maximum compressive residual stresses in tooth flanks were determined.

Keywords: Water – air spray cooling; Induction hardening; Surface residual stresses; Microstructure
* Dipl.-Wirtsch.-Ing. Dmytro Rodman, Leibniz Universität Hannover, Institute of Materials Science, An der Universität 2, 30823 Garbsen, Germany. Tel.: +49(0) 51176218087, Fax: +49(0)51 17625245, E-mail:

Dedicated to Prof. Dr.-Ing. Christina Berger on the occasion of her 65th birthday

References

[1] J.Grum, in: G.Totten, M.Howes, T.Inoue (Eds.), Handbook of Residual Stress and Deformation of Steel, Vol. 2, ASM Interna- tional, Materials Park, Ohio (2002) 220–247.Suche in Google Scholar

[2] J.Grum: Int. J. Mater. Prod. Technol.24 (2005) 53–97. DOI: 10.1504/IJMPT.2005.00794210.1504/IJMPT.2005.007942Suche in Google Scholar

[3] J.Betzold, J.Pucelik, S.Eisenberg: Mat.-wiss. u. Werkstofftech.38 (2007) 263–273. DOI:10.1002/mawe.20070013310.1002/mawe.200700133Suche in Google Scholar

[4] R.E.Haimbaugh: Practical Induction Heat Treating, Vol. 1, ASM International, Materials Park, Ohio (2001) 123–130.Suche in Google Scholar

[5] H.Beitz, Th.Beitz: BHM150 (2005) 96–100.Suche in Google Scholar

[6] F.Moreaux, P.Archaumbault, G.Beck, Y.Pourprix: HTM44 (1989) 129–132.10.1515/htm-1989-440304Suche in Google Scholar

[7] D.Rodman, C.Krause, F.Nörnberger, Fr.-W.Bach, K.Haskamp, M.Köstner, E.Reithmeier: Steel Research International82 (2011) 329–336. DOI:10.1002/srin.20100021810.1002/srin.201000218Suche in Google Scholar

[8] I.V.Frolov, Th.Gretzki, Z.Yu, F.Nuernberger, Th.Hassel, Fr.-W.Bach: Conf. Proc. Achievements and prospects of develop- ment of processes and equipment of working by pressure in metal- lurgy and mechanical engineering, Kramatorsk, 21st 24th of April (2009) 270–275.Suche in Google Scholar

[9] DJ.Williams: Metal Heat Treating (1995) 33–37.Suche in Google Scholar

[10] E.Macherauch, P.Möller: Z. f. angew. Physik13 (1961) 305–312.Suche in Google Scholar

[11] G.Benkowsky: Induktionserwörmung: Hörten, Glöhen, Schmel- zen, Löten, Schweiöen; Grundlagen und praktische Anleitungen för Induktionserwörmungsverfahren, insbesondere auf dem Ge- biet der Hochfrequenzerwörmung, Verlag Technik GmbH, Berlin (1990) 86.Suche in Google Scholar

[12] L.Markegard, H.Kristoffersen: Proc. of New Challenges in Heat Treatment and Surface Engineering Conference in Honour of Prof. Bozidar Liscic, Dubrovnik, 9-12 June (2009) 359–366.Suche in Google Scholar

[13] H.Beitz: HTM44 (1989) 188–191.10.1515/htm-1989-440319Suche in Google Scholar

[14] V.Rudnev: IndustrialHeating.com March (2005) 1–5.Suche in Google Scholar

[15] H.Fahry, H.-W.Zoch, H.Schlicht: HTM44 (1989) 149–156.10.1515/htm-1989-440309Suche in Google Scholar

[16] J.Volkmuth: HTM51 (1996) 145–154.10.1515/htm-1996-510304Suche in Google Scholar

Received: 2011-3-14
Accepted: 2011-8-1
Published Online: 2013-06-11
Published in Print: 2012-01-01

© 2012, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial January 2012
  5. Original Contributions
  6. High-strength aluminum-based light-weight materials for safety components – recent progress by microstructural refinement and particle reinforcement
  7. Microstructure – deformation relationships in fine grained high manganese TWIP steel – the role of local texture
  8. Microstructure of a eutectic NiAl—Mo alloy directionally solidified using an industrial scale and a laboratory scale Bridgman furnace
  9. Effect of Si addition on the oxidation resistance of Co–Re–Cr-alloys: Recent attainments in the development of novel alloys
  10. Corrosion behavior of silicon oxycarbide-based ceramic nanocomposites under hydrothermal conditions
  11. Thermal cycling damage evolution of a thermal barrier coating and the influence of substrate creep, interface roughness and pre-oxidation
  12. Influence of creep and cyclic oxidation in thermal barrier coatings
  13. Residual stress states as a result of bending and straightening processes of steels in different heat treatment conditions
  14. Residual stresses under quasi-static and cyclic loading in shot peened Inconel 718
  15. Investigation of the surface residual stresses in spray cooled induction hardened gearwheels
  16. Stress-gradient induced fatigue at ultra high frequencies in sub micron thin metal films
  17. Influence of graphite spherical size on fatigue behaviour and fracture toughness of ductile cast iron EN-GJS-400-18LT
  18. Failure behaviour of the superalloy MAR-M247 LC under LCF, HCF and combined LCF/HCF loading
  19. Measuring techniques for the very high cycle fatigue behaviour of high strength steel at ultrasonic frequencies
  20. Failure limits of continuous carbon fibre reinforced plastics loaded with fibre parallel compression
  21. Development of an integrative simulation method to predict the microstructural influence on the mechanical behaviour of semi-crystalline thermoplastic parts
  22. DGM News
  23. DGM News
https://doi.org/10.3139/146.110622
Schlagwörter für diesen Artikel
Water – air spray cooling; Induction hardening; Surface residual stresses; Microstructure

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial January 2012
  5. Original Contributions
  6. High-strength aluminum-based light-weight materials for safety components – recent progress by microstructural refinement and particle reinforcement
  7. Microstructure – deformation relationships in fine grained high manganese TWIP steel – the role of local texture
  8. Microstructure of a eutectic NiAl—Mo alloy directionally solidified using an industrial scale and a laboratory scale Bridgman furnace
  9. Effect of Si addition on the oxidation resistance of Co–Re–Cr-alloys: Recent attainments in the development of novel alloys
  10. Corrosion behavior of silicon oxycarbide-based ceramic nanocomposites under hydrothermal conditions
  11. Thermal cycling damage evolution of a thermal barrier coating and the influence of substrate creep, interface roughness and pre-oxidation
  12. Influence of creep and cyclic oxidation in thermal barrier coatings
  13. Residual stress states as a result of bending and straightening processes of steels in different heat treatment conditions
  14. Residual stresses under quasi-static and cyclic loading in shot peened Inconel 718
  15. Investigation of the surface residual stresses in spray cooled induction hardened gearwheels
  16. Stress-gradient induced fatigue at ultra high frequencies in sub micron thin metal films
  17. Influence of graphite spherical size on fatigue behaviour and fracture toughness of ductile cast iron EN-GJS-400-18LT
  18. Failure behaviour of the superalloy MAR-M247 LC under LCF, HCF and combined LCF/HCF loading
  19. Measuring techniques for the very high cycle fatigue behaviour of high strength steel at ultrasonic frequencies
  20. Failure limits of continuous carbon fibre reinforced plastics loaded with fibre parallel compression
  21. Development of an integrative simulation method to predict the microstructural influence on the mechanical behaviour of semi-crystalline thermoplastic parts
  22. DGM News
  23. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 16.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.110622/pdf?lang=de
Button zum nach oben scrollen