Home Technology ALCHEMI study of chromium doped iron-aluminides
Article
Licensed
Unlicensed Requires Authentication

ALCHEMI study of chromium doped iron-aluminides

  • Jozef Veselý , Miroslav Cieslar and Margarita Slámová
Published/Copyright: June 11, 2013
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 100 Issue 6

Abstract

Mechanical properties of intermetallic iron-aluminides are strongly influenced by thermal pretreatment, stoichiometry and additional alloying elements.

In the present study samples of FeAl and FeAl alloyed with Cr annealed at different temperatures were investigated. A revised ALCHEMI technique (Atom Location by CHanneling Enhanced MIcroanalysis) was employed to study site occupancies. The orientation dependences of characteristic X-ray yields were measured. Dynamic electron diffraction conditions with the systematic row excitation (planar ALCHEMI) were used. Experimental data were fitted by a theoretical calculation based on Bloch wave method.

The distribution of elements on individual sublattices was obtained and preferential occupation of Al sites by Cr was confirmed.

Keywords: FeAl; ALCHEMI; TEM; EDX
* Correspondence address, Jozef Veselý, Charles University in Prague, Faculty of Mathematics and Physics, Department of Physics of Materials, Ke Karlovu 5, CZ-12116 Prague 2, Czech Republic, Tel.: +420 221 911 356, Fax: +420 221 911 490, E-mail:

References

[1] J.Taftø, J.C.H.Spence: Science218 (1982) 49–51.DOI:10.1126/science.218.4567.4910.1126/science.218.4567.49Search in Google Scholar PubMed

[2] Z.Horita, S.Matsumura, T.Baba: Ultramicroscopy58 (1995) 327–335. DOI:10.1016/0304-3991(95)00012-P10.1016/0304-3991(95)00012-PSearch in Google Scholar

[3] M.T.Otten, P.R.Buseck: Ultramicroscopy23 (1987) 151–158.DOI:10.1016/0304-3991(87)90160-410.1016/0304-3991(87)90160-4Search in Google Scholar

[4] W.Nüchter, W.Sigle: Phil. Mag. A71 (1995) 165–186.DOI:10.1080/0141861950824296310.1080/01418619508242963Search in Google Scholar

[5] M.P.Oxley, L.J.Allen: Acta Cryst. A56 (2000) 470–490.DOI:10.1107/S010876730000707810.1107/S0108767300007078Search in Google Scholar

[6] C.J.Humphreys: Rep. Prog. Phys.42 (1979) 1825–1887.DOI:10.1088/0034-4885/42/11/00210.1088/0034-4885/42/11/002Search in Google Scholar

[7] D.M.Bird, Q.A.King: Acta Cryst. A46 (1990) 202–208.DOI:10.1107/S010876738901190610.1107/S0108767389011906Search in Google Scholar

[8] V.F.Sears, S.A.Shelley: Acta Cryst. A47 (1991) 441–446.DOI:10.1107/S010876739100297010.1107/S0108767391002970Search in Google Scholar

[9] M.P.Oxley, L.J.Allen: Phys. Rev. B57 (1998) 3273–3282.DOI:10.1103/PhysRevB.57.327310.1103/PhysRevB.57.3273Search in Google Scholar

[10] I.M.Anderson: Acta Mater.45 (1997) 3897–3909.DOI:10.1016/S1359-6454(97)00042-610.1016/S1359-6454(97)00042-6Search in Google Scholar

[11] J.Pešička, G.Schmitz: Intermetallics10 (2002) 717–722.DOI:10.1016/S0966-9795(02)00045-610.1016/S0966-9795(02)00045-6Search in Google Scholar

Received: 2008-8-28
Accepted: 2009-2-17
Published Online: 2013-06-11
Published in Print: 2009-06-01

© 2009, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Feature
  4. Beyond fick's equations, an overview
  5. Review
  6. The high-temperature creep properties of materials processed using severe plastic deformation
  7. Nanostructuring of metallic materials by spd processing for advanced properties
  8. Basic
  9. Some factors affecting the creep behaviour of metallic materials processed by equal-channel angular pressing
  10. The elastic–plastic transition in nanograined polycrystals
  11. Synchrotron X-ray line-profile analysis experiments for the in-situ microstructural characterisation of SPD nanometals during tensile deformation
  12. Tensile and fatigue properties of sub-microcrystalline ultra-low carbon steel produced by hpt-straining
  13. Precipitation Effects in Ultra-Fine-Grained Mg–RE Alloys
  14. EBSD investigation of the grain boundary distributions in ultrafine-grained Cu and Cu–Zr polycrystals prepared by equal-channel angular pressing
  15. Acoustic emission study of the deformation behaviour of magnesium sheets
  16. Mechanical properties of pure titanium and Ti-6Al-4V alloys with a new tailored nano/meso hybrid microstructure
  17. In-situ SEM/EBSD observation of abnormal grain growth in electrodeposited nanocrystalline nickel
  18. High-temperature creep properties of Fe–Al alloys modified by Zr
  19. ALCHEMI study of chromium doped iron-aluminides
  20. Intermetallic compounds at the interface between Sn–Cu(–Ni) solders and Cu substrate
  21. The effect of the microstructure on elastic properties of a polycrystalline stoichiometric NiAl
  22. Ab-initio simulation of the tensile strength of silicon nanofilms
  23. New properties of halogen plasma-treated Cu films
  24. Applied
  25. High-speed deformation of titanium during dynamic channel-angular pressing
  26. Microstructural evolution of equal-channel angular pressed interstitial-free steel
  27. Effect of equal channel angular pressing on microstructure, texture, and high-cycle fatigue performance of wrought magnesium alloys
  28. The characteristics of superplastic flow in a magnesium alloy processed by ECAP
  29. Deformation behaviour of ultrafine-grained 7075 aluminium alloy
  30. The optimization of ECAP conditions to achieve high strain-rate superplasticity in a Zr- and Sc-modified aa 7075 aluminum alloy
  31. Multilayer composite al99.99/almg3 sheets prepared by accumulative roll bonding
  32. Preparation of ultrafine-grained twin-roll cast AlMg3 sheets by accumulative roll bonding
  33. Recovery and recrystallization behavior of aluminum processed by extrusion-preceded equal channel angular pressing
  34. Low sliding-wear resistance of ultrafine-grained Al alloys and steel having undergone severe plastic deformation
  35. Study of the recrystallization of AW-5049 and AW-5754 twin-roll cast alloys by EBSD
  36. XRD profile analysis of ECAP Cu and Cu + Zr samples
  37. Stability of microstructure in silver processed by severe plastic deformation
  38. Acoustic emission study of the mechanical anisotropy of the extruded AZ31 alloy
  39. Effects of shot peening on internal friction in cp aluminum and aluminum alloy 6008
  40. Effects of grain growth on microhardness and coercivity in electrodeposited nanocrystalline nickel
  41. Strain release from pre-deformed Ni53.6Mn27.1Ga19.3 shape memory alloy during thermal cycling
  42. Simulation of the growth kinetics of FeB and Fe2B phases on the AISI M2 borided steel: Effect of the paste thickness
  43. High-pressure torsion deformation of a magnesium-based nanocomposite
  44. Fracture behavior of Mg–Li matrix composites
  45. Notifications
  46. The 80th Birthday of Dr.-Ing. Wolfgang Eychmüller
  47. Personal
https://doi.org/10.3139/146.110121
Keywords for this article
FeAl; ALCHEMI; TEM; EDX

Articles in the same Issue

  1. Contents
  2. Contents
  3. Feature
  4. Beyond fick's equations, an overview
  5. Review
  6. The high-temperature creep properties of materials processed using severe plastic deformation
  7. Nanostructuring of metallic materials by spd processing for advanced properties
  8. Basic
  9. Some factors affecting the creep behaviour of metallic materials processed by equal-channel angular pressing
  10. The elastic–plastic transition in nanograined polycrystals
  11. Synchrotron X-ray line-profile analysis experiments for the in-situ microstructural characterisation of SPD nanometals during tensile deformation
  12. Tensile and fatigue properties of sub-microcrystalline ultra-low carbon steel produced by hpt-straining
  13. Precipitation Effects in Ultra-Fine-Grained Mg–RE Alloys
  14. EBSD investigation of the grain boundary distributions in ultrafine-grained Cu and Cu–Zr polycrystals prepared by equal-channel angular pressing
  15. Acoustic emission study of the deformation behaviour of magnesium sheets
  16. Mechanical properties of pure titanium and Ti-6Al-4V alloys with a new tailored nano/meso hybrid microstructure
  17. In-situ SEM/EBSD observation of abnormal grain growth in electrodeposited nanocrystalline nickel
  18. High-temperature creep properties of Fe–Al alloys modified by Zr
  19. ALCHEMI study of chromium doped iron-aluminides
  20. Intermetallic compounds at the interface between Sn–Cu(–Ni) solders and Cu substrate
  21. The effect of the microstructure on elastic properties of a polycrystalline stoichiometric NiAl
  22. Ab-initio simulation of the tensile strength of silicon nanofilms
  23. New properties of halogen plasma-treated Cu films
  24. Applied
  25. High-speed deformation of titanium during dynamic channel-angular pressing
  26. Microstructural evolution of equal-channel angular pressed interstitial-free steel
  27. Effect of equal channel angular pressing on microstructure, texture, and high-cycle fatigue performance of wrought magnesium alloys
  28. The characteristics of superplastic flow in a magnesium alloy processed by ECAP
  29. Deformation behaviour of ultrafine-grained 7075 aluminium alloy
  30. The optimization of ECAP conditions to achieve high strain-rate superplasticity in a Zr- and Sc-modified aa 7075 aluminum alloy
  31. Multilayer composite al99.99/almg3 sheets prepared by accumulative roll bonding
  32. Preparation of ultrafine-grained twin-roll cast AlMg3 sheets by accumulative roll bonding
  33. Recovery and recrystallization behavior of aluminum processed by extrusion-preceded equal channel angular pressing
  34. Low sliding-wear resistance of ultrafine-grained Al alloys and steel having undergone severe plastic deformation
  35. Study of the recrystallization of AW-5049 and AW-5754 twin-roll cast alloys by EBSD
  36. XRD profile analysis of ECAP Cu and Cu + Zr samples
  37. Stability of microstructure in silver processed by severe plastic deformation
  38. Acoustic emission study of the mechanical anisotropy of the extruded AZ31 alloy
  39. Effects of shot peening on internal friction in cp aluminum and aluminum alloy 6008
  40. Effects of grain growth on microhardness and coercivity in electrodeposited nanocrystalline nickel
  41. Strain release from pre-deformed Ni53.6Mn27.1Ga19.3 shape memory alloy during thermal cycling
  42. Simulation of the growth kinetics of FeB and Fe2B phases on the AISI M2 borided steel: Effect of the paste thickness
  43. High-pressure torsion deformation of a magnesium-based nanocomposite
  44. Fracture behavior of Mg–Li matrix composites
  45. Notifications
  46. The 80th Birthday of Dr.-Ing. Wolfgang Eychmüller
  47. Personal
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 31.12.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.110121/pdf
Scroll to top button