Home Technology Effect of crystallization on the deformation behavior of a Zr-based bulk metallic glass
Article
Licensed
Unlicensed Requires Authentication

Effect of crystallization on the deformation behavior of a Zr-based bulk metallic glass

  • János Lendvai , Jenő: Gubicza , János L. Lábár and Zoltán Kuli
Published/Copyright: June 11, 2013
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 100 Issue 3

Abstract

The crystallization process in a Zr-based bulk metallic glass with the composition Zr44Ti11Cu10Ni10Be25 was studied during isothermal annealing above the glass transition temperature at 682 K. Indentation creep tests were applied to study the effect of crystallization on the viscosity. It was found that the increase in viscosity during crystallization is primarily caused by the hard crystalline grains and secondarily by the change of the chemical composition of the remaining liquid phase. The deformation behavior at room temperature is studied by three-point bending tests. The strength of the specimens decreases significantly in the first step of the crystallization process.

Keywords: Metallic glass; Quasicrystal; Indentation creep; Viscosity; Strength
* Correspondence address, Prof. János Lendvai, Pázmány Péter sétány 1/A., H-1117 Budapest, Hungary, Tel.: +36 1 372 2845, Fax: +36 1 372 2811, E-mail:

References

[1] T.A.Waniuk, R.Busch, A.Masuhr, W.L.Johnson: Acta Mater.46 (1998) 5229.Search in Google Scholar

[2] A.Inoue: Mater. Sci. Eng. A304 (2001) 1.Search in Google Scholar

[3] B.C.Wei, G.S.Yu, W.Löser, L.Xia, S.Roth, W.H.Wang, J.Eckert: Mater. Sci. Eng. A375 (2004) 1161.Search in Google Scholar

[4] C.A.Schuh, T.C.Hufnagel, U.Ramamurty: Acta Mater.55 (2007) 4067.Search in Google Scholar

[5] L.-Q.Xing, Y.Li, K.T.Ramesh, J.Li, T.C.Hufnagel: Phys. Rev. B64 (2001) 180201(R).Search in Google Scholar

[6] D.Fátay, J.Gubicza, J.Lendvai: J. Alloys Comp.434–435 (2007) 75.Search in Google Scholar

[7] M.Wollgarten, S.Mechler, E.Davidov, N.Wanderka, M.-P.Macht: Intermetallics12 (2004) 1251.Search in Google Scholar

[8] D.Fátay, J.Gubicza, P.Szommer, J.Lendvai, M.Blétry, P.Guyot: Mater. Sci. Eng. A387 (2004) 1001.Search in Google Scholar

[9] J.Gubicza, J.L.Lábár, E.Agócs, D.Fátay, J.Lendvai: Scripta Mater.58 (2008) 291.Search in Google Scholar

[10] C.-H.Hsueh, P.F.Becher: J. Am. Ceram. Soc.88 (2005) 1046.Search in Google Scholar

[11] D.Suh, R.H.Dauskardt: J. Non-Cryst. Solids317 (2003) 181.Search in Google Scholar

Received: 2008-9-1
Accepted: 2009-1-12
Published Online: 2013-06-11
Published in Print: 2009-03-01

© 2009, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Editorial
  4. 11th ISPMA in Prague
  5. Feature
  6. Physical aspects of plastic deformation in Mg–Al alloys with Sr and Ca
  7. Review
  8. Fe–Al materials for structural applications at high temperatures: Current research at MPIE
  9. Basic
  10. Very high cycle fatigue behaviour of as-extruded AZ31, AZ80, and ZK60 magnesium alloys
  11. Phase composition and morphology development in WE-type alloys modified by high Zn content
  12. Microstructural investigation of the failure mechanisms after creep exposure of Mg–Y–Nd–Zn–Mn alloy
  13. Theoretical investigation of phase equilibria by the continuous displacement cluster variation method
  14. Alloying behaviour of binary transition metal systems
  15. Surface composition of a Ag-5.1Cu (mass%) alloy
  16. Temperature and strain rate dependent flow criterion for bcc transition metals based on atomistic analysis of dislocation glide
  17. Strain-hardening behaviour of AZ31 magnesium alloys
  18. Bauschinger effect in thin metal films simulated by the continuum dislocation-based model
  19. Core structure of screw dislocations in hcp Ti: an ab initio DFT study
  20. Long-range internal stresses in monotonically and cyclically deformed metallic single crystals
  21. Energetic formulation of nonlocal crystal plasticity
  22. Austenite–martensite interfaces in strained foils of CuAlNi alloy
  23. Mechanical anisotropy and ideal strength in a multifunctional Ti–Nb–Ta–Zr–O alloy (Gum Metal)
  24. Low-cycle fatigue properties of TiAl alloy with high Nb content
  25. Mechanism and kinetics of the intermediary phase formation in Ti–Al and Ti–Al–Si systems during reactive sintering
  26. Influence of the dynamic crystallization conditions on the martensitic transformation in the Ti40.7Hf9.5Ni39.8Cu10 shape memory alloy
  27. Isostructural phase transition in hexagonal Ce1–xYxPdAl compounds
  28. Structural and phase transformations in Zr and Zr–Nb alloys under loading by spherical converging stress waves
  29. Influence of titanium volume fraction on the mechanical properties of Mg–Ti composites
  30. Applied
  31. Effects of prior homogenization treatments on microstructure development and mechanical properties of the extruded wrought magnesium alloy ZK60
  32. Annealing effects after various thermo-mechanical treatments on microstructure and mechanical properties of the wrought magnesium alloy AZ80
  33. Vacancy–solute interaction in magnesium alloy WE54 during artificial ageing: a positron annihilation spectroscopy study
  34. FeAl-based alloys cast in an ultrasound field
  35. High-temperature mechanical properties of Fe-40 at.% Al based intermetallic alloys with C or Ti addition
  36. The influence of dispersoids on the recrystallization of aluminium alloys
  37. High-rate plastic deformation of a copper single crystal under loading by spherical converging shock waves
  38. Hardening and softening in an Mg–Al–Ca matrix alloy reinforced with short graphite fibres
  39. Deformation behaviour of microcrystalline magnesium reinforced by alumina nano- and microparticles
  40. Thresholds in creep of magnesium alloy AX41 composites reinforced with short fibers
  41. Recovery processes in magnesium alloy AX41 and AX41-12 vol.% C-fibre composite studied by dilatometry
  42. Directional crystallisation of Ti–Al–Si in-situ composites
  43. Microstructure and mechanical properties of the AA6082 aluminium alloy with small additions of Sc and Zr
  44. Microstructure of a ternary Al–Pd–Rh alloy
  45. Effect of annealing on microstructure and properties of twin-roll-cast Al–Mn alloys with different copper content
  46. Quantitative characterization of the orientation spread within individual grains in copper after tensile deformation
  47. Effect of crystallization on the deformation behavior of a Zr-based bulk metallic glass
  48. Changes in structure and properties of carbide-steel cermets resulted from a heat treatment
  49. Comparative study of the high-temperature behaviour of Mg–Al and Mg–Zn wrought alloys
  50. Notification
  51. DGM News
https://doi.org/10.3139/146.110053
Keywords for this article
Metallic glass; Quasicrystal; Indentation creep; Viscosity; Strength

Articles in the same Issue

  1. Contents
  2. Contents
  3. Editorial
  4. 11th ISPMA in Prague
  5. Feature
  6. Physical aspects of plastic deformation in Mg–Al alloys with Sr and Ca
  7. Review
  8. Fe–Al materials for structural applications at high temperatures: Current research at MPIE
  9. Basic
  10. Very high cycle fatigue behaviour of as-extruded AZ31, AZ80, and ZK60 magnesium alloys
  11. Phase composition and morphology development in WE-type alloys modified by high Zn content
  12. Microstructural investigation of the failure mechanisms after creep exposure of Mg–Y–Nd–Zn–Mn alloy
  13. Theoretical investigation of phase equilibria by the continuous displacement cluster variation method
  14. Alloying behaviour of binary transition metal systems
  15. Surface composition of a Ag-5.1Cu (mass%) alloy
  16. Temperature and strain rate dependent flow criterion for bcc transition metals based on atomistic analysis of dislocation glide
  17. Strain-hardening behaviour of AZ31 magnesium alloys
  18. Bauschinger effect in thin metal films simulated by the continuum dislocation-based model
  19. Core structure of screw dislocations in hcp Ti: an ab initio DFT study
  20. Long-range internal stresses in monotonically and cyclically deformed metallic single crystals
  21. Energetic formulation of nonlocal crystal plasticity
  22. Austenite–martensite interfaces in strained foils of CuAlNi alloy
  23. Mechanical anisotropy and ideal strength in a multifunctional Ti–Nb–Ta–Zr–O alloy (Gum Metal)
  24. Low-cycle fatigue properties of TiAl alloy with high Nb content
  25. Mechanism and kinetics of the intermediary phase formation in Ti–Al and Ti–Al–Si systems during reactive sintering
  26. Influence of the dynamic crystallization conditions on the martensitic transformation in the Ti40.7Hf9.5Ni39.8Cu10 shape memory alloy
  27. Isostructural phase transition in hexagonal Ce1–xYxPdAl compounds
  28. Structural and phase transformations in Zr and Zr–Nb alloys under loading by spherical converging stress waves
  29. Influence of titanium volume fraction on the mechanical properties of Mg–Ti composites
  30. Applied
  31. Effects of prior homogenization treatments on microstructure development and mechanical properties of the extruded wrought magnesium alloy ZK60
  32. Annealing effects after various thermo-mechanical treatments on microstructure and mechanical properties of the wrought magnesium alloy AZ80
  33. Vacancy–solute interaction in magnesium alloy WE54 during artificial ageing: a positron annihilation spectroscopy study
  34. FeAl-based alloys cast in an ultrasound field
  35. High-temperature mechanical properties of Fe-40 at.% Al based intermetallic alloys with C or Ti addition
  36. The influence of dispersoids on the recrystallization of aluminium alloys
  37. High-rate plastic deformation of a copper single crystal under loading by spherical converging shock waves
  38. Hardening and softening in an Mg–Al–Ca matrix alloy reinforced with short graphite fibres
  39. Deformation behaviour of microcrystalline magnesium reinforced by alumina nano- and microparticles
  40. Thresholds in creep of magnesium alloy AX41 composites reinforced with short fibers
  41. Recovery processes in magnesium alloy AX41 and AX41-12 vol.% C-fibre composite studied by dilatometry
  42. Directional crystallisation of Ti–Al–Si in-situ composites
  43. Microstructure and mechanical properties of the AA6082 aluminium alloy with small additions of Sc and Zr
  44. Microstructure of a ternary Al–Pd–Rh alloy
  45. Effect of annealing on microstructure and properties of twin-roll-cast Al–Mn alloys with different copper content
  46. Quantitative characterization of the orientation spread within individual grains in copper after tensile deformation
  47. Effect of crystallization on the deformation behavior of a Zr-based bulk metallic glass
  48. Changes in structure and properties of carbide-steel cermets resulted from a heat treatment
  49. Comparative study of the high-temperature behaviour of Mg–Al and Mg–Zn wrought alloys
  50. Notification
  51. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2026 De Gruyter Brill
Downloaded on 19.2.2026 from https://www.degruyterbrill.com/document/doi/10.3139/146.110053/html
Scroll to top button