Wear testing of in situ cast AA8011-TiB2 metal matrix composites
-
Bellamballi Munivenkatappan Muthamizh Selvan
Abstract
An aluminum alloy 8011 was reinforced with varying weight percentages of TiB2 using an in situ stir casting technique by adding inorganic halide salts of K2TiF6 and KBF4 in molten AA8011 matrix alloy. X-ray diffraction and scanning electron microscopy were performed on the cast materials to confirm the presence and distribution of the reinforcements in the composite materials. To investigate the wear behavior of the cast materials, pin on disc wear testing was carried out at varied levels of sliding distance, amount of reinforcement, temperature, load and sliding velocity based on Taguchi's L18 orthogonal array with wear rate as the response. AA 8011 with a reinforcement of 4 wt.-%, 1500 m sliding distance, at a temperature of 100 °C, load 10 N and sliding velocity 2 m × s−1 provided the best wear resistance. The significance and influence of factors on wear rate were analyzed by an analysis of the variance.
References
1 Donaldson Steven , B. MiracleDaniel: ASM Handbook Vol. 21, Composites, American Society of Materials, Materials Park, Ohio, USA (2001)Search in Google Scholar
2 N. Natarajan , S.Vijayarangan, I.Rajendran: Wear behaviour of A356/25SiCp aluminum matrix composites sliding against automobile friction material, Wear261 (2006), No. 7, pp. 812–82210.1016/j.wear.2006.01.011Search in Google Scholar
3 Pei-peng Jin , GangChen, LiHan, Jin-huiWang: Dry sliding friction and wear behaviors of Mg2B2O5 whisker reinforced 6061Al matrix composites, Transactions of Nonferrous Metals Society of China24 (2010), No. 1, pp. 49–5710.1016/S1003-6326(14)63027-2Search in Google Scholar
4 S. Kumar , R. S.Panwar, O. P.Pandey: Effect of dual reinforced ceramic particles on high temperature tribological properties of aluminum composites, Ceramics International39 (2013), No. 6, pp. 6333–634210.1016/j.ceramint.2013.01.059Search in Google Scholar
5 W. Tian , L.Qi, C.Su, J.Liu, J.Zhou: Effect of fiber transverse isotropy on effective thermal conductivity of metal matrix composites reinforced by randomly distributed fibers, Composite Structures152 (2016), pp. 637–64410.1016/j.compstruct.2016.05.070Search in Google Scholar
6 G. Ranganath , S. C.Sharma, M.Krishna: Dry sliding wear of garnet reinforced zinc/aluminum metal matrix composites, Wear251 (2001), No. 1, pp. 1408–141310.1016/S0043-1648(01)00781-5Search in Google Scholar
7 S. Baskaran , V.Anandakrishnan, M.Duraiselvam: Investigations on dry sliding wear behavior of in situ casted AA7075–TiC metal matrix composites by using Taguchi technique, Materials and Design60 (2014), pp. 184–19210.1016/j.matdes.2014.03.074Search in Google Scholar
8 S. Mohan , G.Gautam, N.Kumar, R. K.Gautam, A.Mohan, A. Kr.Jaiswal: Dry sliding wear behavior of Al-SiO2 composites, Composite Interfaces23 (2016), No. 6, pp. 493–50210.1080/09276440.2016.1149363Search in Google Scholar
9 G. H. Majzoobi , A.Atrian, M. H.Enayati: Tribological properties of Al7075-SiC nano-composite prepared by hot dynamic compaction, Composite Interfaces22 (2015), No. 7, pp. 579–59310.1080/09276440.2015.1055955Search in Google Scholar
10 K. S. Alhawari , M. Z.Omar, M. J.Ghazali, M. S.Salleh, M. N.Mohammed: Dry sliding wear behaviour of thixoformed hypoeutectic Al–Si–Cu alloy with different amounts of magnesium, Composite Interfaces23 (2016), No. 6, pp. 519–53110.1080/09276440.2016.1164496Search in Google Scholar
11 A. A. Adebisi , M. A.Maleque, M. Y.Ali, K. A.Bello: Effect of variable particle size reinforcement on mechanical and wear properties of 6061Al–SiCp composite, Composite Interfaces23 (2016), No. 6, pp. 533–54710.1080/09276440.2016.1167414Search in Google Scholar
12 S. Sheibani , M. F.Najafabadi: In situ fabrication of Al–TiC metal matrix composites by reactive slag process, Materials and Design28 (2007), No. 8, pp. 2373–237810.1016/j.matdes.2006.08.004Search in Google Scholar
13 L. A. Mabhali , N.Sacks, S.Pityana: Three body abrasion of laser surface alloyed aluminum AA1200, Wear290 (2012), pp. 1–910.1016/j.wear.2012.05.034Search in Google Scholar
14 A. Edrisy , T.Perry, A. T.Alpas: investigation of scuffing damage in aluminum engines with thermal spray coatings, Wear259 (2005), No. 7, pp. 1056–106210.1016/j.wear.2005.02.048Search in Google Scholar
15 F. Chen , Z.Chen, F.Mao, T.Wang, Z.Cao: TiB2 reinforced aluminum based in situ composites fabricated by stir casting, Materials Science and Engineering A625 (2015), pp. 357–36810.1016/j.msea.2014.12.033Search in Google Scholar
16 A. Mohan , G.Gautam, N.Kumar, S.MohanR. K. C.Gautam: Synthesis and tribological properties of AA5052 base insitu composites, Composite Interfaces23 (2016), No. 6, pp. 503–51810.1080/09276440.2016.1155386Search in Google Scholar
17 C. S. Ramesh , S.Pramod, R.Keshavamurthy: A study on microstructure and mechanical properties of Al 6061–TiB2 in-situ composites, Materials Science and Engineering A528 (2011), No. 12, pp. 4125–413210.1016/j.msea.2011.02.024Search in Google Scholar
18 A. Kumar , R. K.Gautam, R.Tyagi: Dry sliding wear characteristics of in situ synthesized Al-TiC composites, Composite Interfaces23 (2016), No. 6, pp. 469–48010.1080/09276440.2016.1148434Search in Google Scholar
19 G. P. Kumar , R.Keshavamurthy, P.Kumari, C.Dubey: Corrosion behaviour of TiB2 reinforced aluminum based in situ metal matrix composites, Perspectives in Sciences8 (2016), pp. 172–17510.1016/j.pisc.2016.04.025Search in Google Scholar
20 Y. Shen , X.Li, T.Hong, J.Geng, H.Wang: Effects of TiB2 particles on microstructure and mechanical properties of an in-situ TiB2-Al–Cu–Li matrix composite, Materials Science and Engineering A655 (2016), pp. 265–26810.1016/j.msea.2015.12.104Search in Google Scholar
21 N. V. Rengasamy , M.Rajkumar, S. S.Kumaran: Mining environment applications on Al 4032–ZrB2 and TiB2 in-situ composites, Journal of Alloys and Compounds658 (2016), pp. 757–77310.1016/j.jallcom.2015.10.257Search in Google Scholar
22 A. P. Sannino , H. J.Rack: Dry sliding wear of discontinuously reinforced aluminum composites: review and discussion, Wear189 (1995), No. 1–2, pp. 1–910.1016/0043-1648(95)06657-8Search in Google Scholar
23 J. Liu , J.Binner, R.Higginson: Dry sliding wear behaviour of co-continuous ceramic foam/aluminum alloy interpenetrating composites produced by pressure less infiltration, Wear276 (2012), pp. 94–10410.1016/j.wear.2011.12.008Search in Google Scholar
24 A. Pramanik : Effects of reinforcement on wear resistance of aluminum matrix composites, Transactions of Nonferrous Metals Society of China26 (2016) No. 2, pp. 348–35810.1016/S1003-6326(16)64125-0Search in Google Scholar
25 L. Yuan , J.Han, J.Liu, Z.Jiang: Mechanical properties and tribological behavior of aluminum matrix composites reinforced with in-situ AlB2 particles, Tribology International98 (2016), pp. 41–4710.1016/j.triboint.2016.01.046Search in Google Scholar
26 S. Madhusudan , M. M.Sarcar, N. R.Bhargava: Sliding wear studies on Aluminum–Copper composites, Composite Interfaces18 (2011), No. 5, pp. 377–38510.1163/156855411X595799Search in Google Scholar
27 R. N. Rao , S.Das, D. P.Mondal, G.Dixit: Dry sliding wear behaviour of cast high strength aluminum alloy (Al–Zn–Mg) and hard particle composites, Wear267 (2009), No. 9, pp. 1688–169510.1016/j.wear.2009.06.034Search in Google Scholar
28 V. Kumar , R. K.Gautam, R.Tyagi: tribological behavior of Al-based self-lubricating composites, Composite Interfaces23 (2016), No. 6, pp. 481–49210.1080/09276440.2016.1148435Search in Google Scholar
29 H. M. Rajan , S.Ramabalan, I.Dinaharan, S. J.Vijay: Effect of TiB2 content and temperature on sliding wear behavior of AA7075/TiB2 in situ aluminum cast composites, Archives of Civil and Mechanical Engineering14 (2014), No. 1, pp. 72–7910.1016/j.acme.2013.05.005Search in Google Scholar
30 C. H. Fei , T. M.Wang, Z. N.Chen, M. A.Feng, H. A.Qiang, Z. Q.CAO: microstructure, mechanical properties and wear behaviour of Zn–Al–Cu–TiB2 in situ composites, Transactions of Nonferrous Metals Society of China25 (2015), No. 1, pp. 103–11110.1016/S1003-6326(15)63584-1Search in Google Scholar
31 N. Radhika , R.Raghu: Three body abrasion wear behaviour of functionally graded Aluminum/B4C metal matrix composite using design of experiments, Proceedia Engineering97 (2014), pp. 713–72210.1016/j.proeng.2014.12.301Search in Google Scholar
32 S. Basavarajappa , G.ChandramohanJ. P.Davim: Application of Taguchi techniques to study dry sliding wear behaviour of metal matrix composites, Materials and Design28 (2007), No. 4, pp. 1393–139810.1016/j.matdes.2006.01.006Search in Google Scholar
33 N. Radhika , R.Subramanian, S. V.Prasat: Tribological behaviour of aluminum/alumina/graphite hybrid metal matrix composite using Taguchi's techniques, Journal of Minerals and Materials Characterization and Engineering10 (2011), No. 5, pp. 427–443Search in Google Scholar
34 S. K. Selvaraj , M. K.Nagarajan, L. A.Kumaraswamidhas: An investigation of abrasive and erosion behaviour of AA 2618 reinforced with Si3N4, AlN and ZrB2 in situ composites by using optimization techniques, Archives of Civil and Mechanical Engineering17 (2017), No. 1, pp. 43–5410.1016/j.acme.2016.08.003Search in Google Scholar
35 P. Ravindran , K.Manisekar, P.Narayanasamy, N.Selvakumar, R.Narayanasamy: Application of factorial techniques to study the wear of Al hybrid composites with graphite addition, Materials and Design39 (2012), pp. 42–5410.1016/j.matdes.2012.02.013Search in Google Scholar
36 G. M. Balamurugan , M.Duraiselvam, V.Anandakrishnan: Comparison of high temperature wear behaviour of plasma sprayed wc–co coated and hard chromium plated AISI 304 austenitic stainless steel, Materials and Design35 (2012), pp. 640–64610.1016/j.matdes.2011.10.012Search in Google Scholar
37 N. S. Prabhakar , N.Radhika, R.Raghu: Analysis of tribological behavior of aluminum/B4C composite under dry sliding motion, Proceedia Engineering97 (2014), pp. 994–100310.1016/j.proeng.2014.12.376Search in Google Scholar
38 L. Zhang , X. B.He, X. H.Qu, B. H.Duan, X.Lu, M. L.Qin: Dry sliding wear properties of high volume fraction SiCp/Cu composites produced by pressureless infiltration, Wear265 (2008), No. 11, pp. 1848–185610.1016/j.wear.2008.04.029Search in Google Scholar
39 Z. Zhang , D. L.Chen: Contribution of orowan strengthening effect in particulate-reinforced metal matrix nano-composites, Materials Science and Engineering: A483 (2008), pp. 148–15210.1016/j.msea.2006.10.184Search in Google Scholar
40 M. Narimani , B.Lotfi, Z.Sadeghian: Evaluation of the microstructure and wear behaviour of AA6063-B4C/TiB2 mono and hybrid composite layers produced by friction stir processing, Surface Coating Technology285 (2016), pp. 1–1010.1016/j.surfcoat.2015.11.015Search in Google Scholar
41 A. Mandal , M.Chakraborty, B. S.Murty: Effect of TiB2 particles on sliding wear behaviour of Al–4Cu alloy, Wear262 (2007), No. 1, pp. 160–16610.1016/j.wear.2006.04.003Search in Google Scholar
42 A. Mandal , B. S.Murty, M.Chakraborty; Wear behaviour of near eutectic Al–Si alloy reinforced with in-situ TiB2 particles, Materials Science and Engineering: A 506 (2009), No. 1, pp. 27–3310.1016/j.msea.2008.11.007Search in Google Scholar
43 S. Suresh , N. S.Moorthi: Process development in stir casting and investigation on microstructures and wear behavior of TiB2 on Al6061 MMC, Proceedia Engineering64 (2013), pp. 1183–119010.1016/j.proeng.2013.09.197Search in Google Scholar
44 I. Dinaharan , N.Murugan: Dry sliding wear behavior of AA6061/ZrB2 in-situ composite, Transactions of Nonferrous Metals Society of China22 (2012), No. 4, pp. 810–81810.1016/S1003-6326(11)61249-1Search in Google Scholar
45 T. Rajmohan , K.Palanikumar, S.Ranganathan: Evaluation of mechanical and wear properties of hybrid aluminum matrix composites, Transactions of Nonferrous Metals Society of China23 (2013), No. 9, pp. 2509–251710.1016/S1003-6326(13)62762-4Search in Google Scholar
46 S. Basavarajappa , G.Chandramohan, K.Mukund, M.Ashwin, M.Prabu: Dry sliding wear behavior of Al 2219/SiCp-Gr hybrid metal matrix composites, Journal of Materials Engineering and Performance15 (2006), No. 6, pp. 668–67410.1361/105994906X150803Search in Google Scholar
© 2019, Carl Hanser Verlag, München
Articles in the same Issue
- Inhalt/Contents
- Contents
- Fachbeiträge/Technical Contributions
- Effects of pre- and post-weld heat treatment conditions on microstructures of cast nickel based superalloys GTD-111 in the laser welding process
- Evaluation of the low-cycle fatigue strength of Sn3.0Ag0.5Cu solder at 313 and 353 K using a small specimen
- The Harris hawks, grasshopper and multi-verse optimization algorithms for the selection of optimal machining parameters in manufacturing operations
- A new hybrid Harris hawks-Nelder-Mead optimization algorithm for solving design and manufacturing problems
- The Harris hawks optimization algorithm, salp swarm algorithm, grasshopper optimization algorithm and dragonfly algorithm for structural design optimization of vehicle components
- Axial crushing behavior of circular aluminum tubes
- Effect of substrate surface preparation on cold sprayed Al-Zn-Al2O3 composite coating properties
- Top-down approach for the estimation of measurement uncertainty based on quality control data and grey system theory
- Hoop tensile and compression behavior of glass-carbon intraply hybrid fiber reinforced filament wound composite pipes
- Non-linear modeling of mechanical properties of plasma arc welded Inconel 617 plates
- Wear testing of in situ cast AA8011-TiB2 metal matrix composites
- Microstructure, mechanical properties and ELM based wear loss prediction of plasma sprayed ZrO2-MgO coatings on a magnesium alloy
- Energy consumption model for the pipe threading process using 10 wt.-% Cu and 316L stainless steel powder-reinforced aluminum 6061 fittings
- Effect of matrix material and orientation angle on tensile and tribological behavior of jute reinforced composites
Articles in the same Issue
- Inhalt/Contents
- Contents
- Fachbeiträge/Technical Contributions
- Effects of pre- and post-weld heat treatment conditions on microstructures of cast nickel based superalloys GTD-111 in the laser welding process
- Evaluation of the low-cycle fatigue strength of Sn3.0Ag0.5Cu solder at 313 and 353 K using a small specimen
- The Harris hawks, grasshopper and multi-verse optimization algorithms for the selection of optimal machining parameters in manufacturing operations
- A new hybrid Harris hawks-Nelder-Mead optimization algorithm for solving design and manufacturing problems
- The Harris hawks optimization algorithm, salp swarm algorithm, grasshopper optimization algorithm and dragonfly algorithm for structural design optimization of vehicle components
- Axial crushing behavior of circular aluminum tubes
- Effect of substrate surface preparation on cold sprayed Al-Zn-Al2O3 composite coating properties
- Top-down approach for the estimation of measurement uncertainty based on quality control data and grey system theory
- Hoop tensile and compression behavior of glass-carbon intraply hybrid fiber reinforced filament wound composite pipes
- Non-linear modeling of mechanical properties of plasma arc welded Inconel 617 plates
- Wear testing of in situ cast AA8011-TiB2 metal matrix composites
- Microstructure, mechanical properties and ELM based wear loss prediction of plasma sprayed ZrO2-MgO coatings on a magnesium alloy
- Energy consumption model for the pipe threading process using 10 wt.-% Cu and 316L stainless steel powder-reinforced aluminum 6061 fittings
- Effect of matrix material and orientation angle on tensile and tribological behavior of jute reinforced composites