Home Effects of Ferroboron and Ferrochromium Powder Addition on Abrasive Wear Resistance of Fe-Based Hardfacing Coatings
Article
Licensed
Unlicensed Requires Authentication

Effects of Ferroboron and Ferrochromium Powder Addition on Abrasive Wear Resistance of Fe-Based Hardfacing Coatings

  • Nilay Yüksel and Salim Şahin
Published/Copyright: September 28, 2014
Become an author with De Gruyter Brill
Submit Manuscript Author Information
Materials Testing
From the journal Materials Testing Volume 56 Issue 9

Abstract

Ferrochromium is used in hardfacing alloys as carbide former. In this study, ferroboron was used with ferrochromium to investigate the effect on microstructure and wear resistance. Five different hardfacing alloys (50 % massive welding wire + 50 % powder mixture) were produced by open arc welding on AISI 1020 steel. Microstructure, SEM and XRD analysis, hardness test, and dry sand/rubber wheel abrasion test were carried out. According to the test results, as the amount of ferroboron increased, wear rate decreased. Minimum wear rate was obtained in 100 % ferroboron powder added sample.

Kurzfassung

Eisenchrom wird in Legierungen für das Auftragsschweißen als Karbidbildner verwendet. In der diesem Beitrag zugrundeliegenden Studie wurde Eisenbor- zusammen mit Eisenchrompulver verwendet, um die Auswirkungen auf die Mikrostruktur und den Verschleißwiderstand zu untersuchen. Fünf verschiedene Auftragsschweißlegierungen (50 % Massivdraht und 50 % Pulvermischung) wurden mittels offenen Lichtbogenschweißens auf einem AISI 1020 Stahl aufgebracht. Mikrostrukturelle, SEM und XRD Analysen sowie Härtetests und Trockensand-Gummirad-Verschleißversuche wurden durchgeführt. Entsprechend der Versuchsergebnisse nahm die Verschleißrate mit zunehmendem Eisenbor-Gehalt ab. Eine minimale Verschleißrate ergab sich für die Probe mit 100 % Eisenborpulver.

*Correspondence Address Nilay Yüksel Celal Bayar University, Engineering Faculty Department of Materials Engineering 45140 Muradiye, Manisa, Turkey E-mail:

Nilay Yüksel was born in Izmir, Turkey, in 1988. She graduated from Celal Bayar University, Turkey in 2010 with a degree in mechanical engineering. She completed her master of science in Department of Mechanical Engineering of Celal Bayar University, Turkey in 2012. Within the same year she has started her PhD study at Celal Bayar University, Turkey.

Salim Şahin was born in Ankara in 1969. He graduated at Dokuz Eylül University, Turkey in 1991 with a degree in mechanical engineering. He completed a Master of Science in mechanical engineering at Celal Bayar University, Turkey in 1995. Then, in 2000 he completed his PhD at Celal Bayar University, Turkey. In 2010, he was appointed associate professor of Materials Engineering Department at Celal Bayar University, Turkey. He works in Materials Engineering Department at Celal Bayar University, Turkey.

References

1 Q.Ming, L. C.Lim, Z. D.Chen: Laser cladding of nickel-based hardfacing alloys, Surf. Coat. Tech.106 (1998), pp. 174–182Search in Google Scholar

2 S. Y.Tu, M. D.Jean, J. T.Wang, C. S.Wu: A robust design in hardfacing using a plasma transfer arc, Int. J. Adv. Manuf. Tech.27 (2006), pp. 889–89610.1007/s00170-004-2265-6Search in Google Scholar

3 G. W.Stachowiak, A. W.Batchelor: Engineering Tribology, 3rd Edition, Elsevier Butterworth Heinemann, Oxford, UK (2005)Search in Google Scholar

4 O. P.Modi, B. K.Prasad, A. K.Jha, V. P.Deshmukh, A. K.Shah: Effects of material composition and microstructural features on dry sliding wear behaviour of Fe-TiC composite and a cobalt-based stellite, Tribol. Lett.17 (2004), pp. 129–1381023-8883/04/0800-0129/0Search in Google Scholar

5 E.Badisch, C.Katsich, H.Winkelmann, F.Franek, M.Roy: Wear behaviour of hardfaced Fe-Cr-C alloy and austenitic steel under 2-body and 3-body conditions at elevated temperature, Tribol. Int.43 (2010), pp. 1234–124410.1016/j.triboint.2010.01.008Search in Google Scholar

6 S.Kumar, D. P.Mondal, A. K.Jha: Effect of Microstructure and chemical composition of hardfacing alloy on abrasive wear behaviour, Porc. of the Int. Conf. JMEPEG9 (2000), pp. 649–655Search in Google Scholar

7 K.Lakshminarayanan, V.Balasubramanian, R.Varahamoorthy, S.Babu: Predicting the dilution of plasma transferred arc hardfacing of stellite on carbon steel using response surface methodology, Met. Mater. Int.14 (2008), pp. 779–78910.3365/met.mat.2008.12.779Search in Google Scholar

8 X.Wang, F.Han, X.Liu, S.Qu, Z.Zou: Microstructure and wear properties of Fe–Ti-V-Mo-C hardfacing alloy, Wear265 (2008), pp. 583–58910.1016/j.wear.2007.12.001Search in Google Scholar

9 X. H.Wang, F.Han, S. Y.Qu, Z. D.Zou: Microstructure of the Fe-based hardfacing layers reinforced by TiC-VC-Mo2C particles, Surf. Coat. Tech.202 (2008), pp. 1502–150910.1016/j.surfcoat.2007.07.002Search in Google Scholar

10 H. P.Bloch, F. K.Geitner: Practical Machinery Management tor Process Plants, Volume 3: Machinery Component Maintenance and Repair, 2nd Edition, Gulf Publishing Company, Houston, Texas, USA (1999)Search in Google Scholar

11 Ö.Özdemir, M.Usta, C.Bindal, A. H.Üçışık: Hard iron boride (Fe2B) on 99.97#8239;wt.-% pure iron, Vacuum80 (2006), pp. 1391–1395Search in Google Scholar

12 W.Xibao: The metallurgical behaviour of B4C in the iron-based surfacing alloy during PTA powder surfacing, Appl. Surf. Sci.252 (2005), pp. 2021–202810.1016/j.apsusc.2005.03.171Search in Google Scholar

13 M.Eroglu: Boride coatings on steel using shielded metal arc welding electrode: Microstructure and hardness, Surf. Coat. Tech.203 (2009), pp. 2229–223510.1016/j.surfcoat.2009.02.010Search in Google Scholar

14 R.Ferro, A.Saccone: Intermetallic Chemistry, 1st Edition, Elsevier, Oxford, UK (2008)Search in Google Scholar

15 J. W.Yoo, S. H.Lee, C. S.Yoon, S. J.Kim: The effect of boron on the wear behaviour of iron-based hardfacing alloys for nuclear power plants valves, J. Nucl. Mater.352 (2006), pp. 90–9610.1016/j.jnucmat.2006.02.071Search in Google Scholar

16 S.Wang, Q.Jiang, X.Chui, Z.He: Effect of boron on carbide morphology of high Cr ledeburite steel, Proc. of the Int. Conf. JMST15 (1999), pp. 286–288Search in Google Scholar

17 J. H.Kim, K. H.Ko, S. D.Noh, G. G.Kim, S. J.Kim: The effect of boron on the abrasive wear behaviour of austenitic Fe-based hardfacing alloys, Wear267 (2009), pp. 1415–141910.1016/j.wear.2009.03.017Search in Google Scholar

18 S.Kumar, D. P.Mondal, H. K.Khaira, A. K.Jha: Improvement in high stress abrasive wear property of steel by hardfacing, Proc. of the Int. Conf. JMEPEG8 (1999), pp. 711–715Search in Google Scholar

19 M.Kirchgaßner, E.Badisch, F.Franek: Behaviour of iron-based hardfacing alloys under abrasion and impact, Wear265 (2008), pp. 772–77910.1016/j.wear.2008.01.004Search in Google Scholar

20 J. J.Coronado, H. F.Caicedo, A. L.Gómez: The effects of welding processes on abrasive wear resistance for hardfacing deposits, Tribol. Int.42 (2009), pp. 745–74910.1016/j.triboint.2008.10.012Search in Google Scholar

Published Online: 2014-09-28
Published in Print: 2014-09-01

© 2014, Carl Hanser Verlag, München

Articles in the same Issue

  1. Inhalt/Contents
  2. Inhalt
  3. Fachbeiträge/Technical Contributions
  4. Burst Strength of Composite Cylinders – Assessment of the Type of Statistical Distribution
  5. Effects of Zn/Cu Ratio and Silicon on Microstructure, Mechanical Properties, Tarnish and Corrosion Resistance of As-Cast 940 Silver Alloys
  6. Analysis of the Frequency as an Integral Method for the Testing of Anisotropic 3D Sheet Metal Structure
  7. Mechanical and Thermal Properties of a Cu-CNT Composite with Carbon Nanotubes Synthesized by CVD Process
  8. The Mechanical and Electrical Properties of the Ternary Bi-Ga-Sb System
  9. Experimental Investigation of the Corrosion Mechanism of Cemented Soils in Magnesium Sulfate Solution
  10. Experimental and Analytical Study of Masonry Constructions Reinforced with Bed Joints
  11. The Fracture Toughness of Fe2B Formed on Boronized AISI 304
  12. Effects of Ferroboron and Ferrochromium Powder Addition on Abrasive Wear Resistance of Fe-Based Hardfacing Coatings
  13. Fabrication of Al/Mg Bimetal Compound Casting by Lost Foam Technique and Liquid-Solid Process
  14. Effects of Si and Zn on Machinability and Wear Resistance of AZ91 and AS91 Magnesium Alloys
  15. DIRECTT-Rekonstruktionen im Vergleich zur gefilterten Rückprojektion
  16. Reduzierung von Missing-Wedge-Artefakten der CT mit DIRECTT
  17. Röntgentomografische Untersuchung eines kommerziellen Lithium-Ionen-Kondensators*
  18. Machining Parameter Optimization of Bidirectional CFRP Composite Pipe by Genetic Algorithm
  19. Investigation of Lost Foam Casted Aluminum Bimetal Microstructures
  20. Taguchi-Based Grey Relation Optimization of Machining Parameters and Cutting Path Strategies in CNC Pocket Milling Operations
  21. Reliable Evaluation of Acceptability of Weld for Final Disposal Based on the Canister Copper Weld Inspection Using Different NDT Methods
  22. Evaluation of the Reliability of NDTesting in Russian Railway Transport
  23. Vorschau/Preview
  24. Vorschau
https://doi.org/10.3139/120.110617

Articles in the same Issue

  1. Inhalt/Contents
  2. Inhalt
  3. Fachbeiträge/Technical Contributions
  4. Burst Strength of Composite Cylinders – Assessment of the Type of Statistical Distribution
  5. Effects of Zn/Cu Ratio and Silicon on Microstructure, Mechanical Properties, Tarnish and Corrosion Resistance of As-Cast 940 Silver Alloys
  6. Analysis of the Frequency as an Integral Method for the Testing of Anisotropic 3D Sheet Metal Structure
  7. Mechanical and Thermal Properties of a Cu-CNT Composite with Carbon Nanotubes Synthesized by CVD Process
  8. The Mechanical and Electrical Properties of the Ternary Bi-Ga-Sb System
  9. Experimental Investigation of the Corrosion Mechanism of Cemented Soils in Magnesium Sulfate Solution
  10. Experimental and Analytical Study of Masonry Constructions Reinforced with Bed Joints
  11. The Fracture Toughness of Fe2B Formed on Boronized AISI 304
  12. Effects of Ferroboron and Ferrochromium Powder Addition on Abrasive Wear Resistance of Fe-Based Hardfacing Coatings
  13. Fabrication of Al/Mg Bimetal Compound Casting by Lost Foam Technique and Liquid-Solid Process
  14. Effects of Si and Zn on Machinability and Wear Resistance of AZ91 and AS91 Magnesium Alloys
  15. DIRECTT-Rekonstruktionen im Vergleich zur gefilterten Rückprojektion
  16. Reduzierung von Missing-Wedge-Artefakten der CT mit DIRECTT
  17. Röntgentomografische Untersuchung eines kommerziellen Lithium-Ionen-Kondensators*
  18. Machining Parameter Optimization of Bidirectional CFRP Composite Pipe by Genetic Algorithm
  19. Investigation of Lost Foam Casted Aluminum Bimetal Microstructures
  20. Taguchi-Based Grey Relation Optimization of Machining Parameters and Cutting Path Strategies in CNC Pocket Milling Operations
  21. Reliable Evaluation of Acceptability of Weld for Final Disposal Based on the Canister Copper Weld Inspection Using Different NDT Methods
  22. Evaluation of the Reliability of NDTesting in Russian Railway Transport
  23. Vorschau/Preview
  24. Vorschau
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 25.10.2025 from https://www.degruyterbrill.com/document/doi/10.3139/120.110617/pdf
Scroll to top button