Home Exploring the implications of CoCrFeNiCu high entropy alloy coatings on tribomechanical, wetting behavior, and interfacial microstructural characterizations in microwave-clad AISI 304 stainless steels
Article
Licensed
Unlicensed Requires Authentication

Exploring the implications of CoCrFeNiCu high entropy alloy coatings on tribomechanical, wetting behavior, and interfacial microstructural characterizations in microwave-clad AISI 304 stainless steels

  • Shubham Sharma ORCID logo EMAIL logo , Shashi Prakash Dwivedi EMAIL logo , Ashutosh Pattanaik , Yashwant Singh Bisht , Teku Kalyani , Vikasdeep Singh Mann , Rajeev Kumar , Abhinav Kumar , Drazan Kozak and Jasmina Lozanovic
Published/Copyright: February 17, 2025
Zeitschrift für Naturforschung A
From the journal Zeitschrift für Naturforschung A Volume 80 Issue 4

Abstract

The exploration of high-performance coatings is specifically necessary for enhancing the mechanical, thermal, and corrosion-resistant characteristics of structural steels in response to the demand for cutting-edge materials in engineering applications. The current study addresses an existing void in the development of durable coatings that gain benefits from the distinctive characteristics of CoCrFeNiCu high entropy alloys (HEA) for stainless steel substrates, with a particular emphasis on SS 304. The primary objective was to examine the microstructural, mechanical, and corrosion behaviors of SS 304 that had been coated with CoCrFeNiCu HEA employing a microwave cladding process. HEA particles were prepared through mechanical milling, and a controlled cladding process was conducted under an inert environment. A variety of meticulous investigations, including Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), and wear rate measurements, have been performed to thoroughly assess crucial parameters, including surface hardness, resistance to corrosion, and wear behavior. This study explores the influence of a CoCrFeNiCu high entropy alloy (HEA) coating (20 % each component) on SS-304 steel. Utilizing microwave cladding, the coating demonstrated a substantial impact on wetting behavior, interfacial microstructure, hardness, and corrosion resistance. Surface hardness was substantially enhanced by the cladding process, resulting in a 54.76 % rise from 210 HV to 325 HV. This enhancement substantially raised the mechanical strength of the steel. Under 120 h of corrosion testing in 3.5 wt.% NaCl, a minimal weight loss of 0.342 mg was observed, suggesting that the material exhibited substantial corrosion resistance. In addition, the material’s capacity to resist abrasive forces has been demonstrated by the relatively minimal wear rate of 0.0012 mm3/m that was noticed throughout wear resistance experiments. Effective interfacial adhesion, bonding strength, and uniform distribution were observed by the coating, which resulted in enhanced mechanical characteristics and durability in harsh circumstances. Wetting characteristics indicated enhanced hydrophobicity/hydrophilicity compared to the uncoated surface. SEM images displayed a well-adhered, homogeneous interfacial region, signifying a robust metallurgical bond. The cladding surface exhibited a uniform distribution of CoCrFeNiCu HEA particles. Notably, the steel’s surface hardness increased by approximately 54.76 % postdeposition. These findings underscore the potential of CoCrFeNiCu HEA coatings in advancing steel surface properties for improved performance and durability. The potential of CoCrFeNiCu HEA coatings to enhance the performance and longevity of SS 304 steel in chemical, marine environments, etc., applications that necessitate superior resistance to wear, protection against corrosion, and structural or mechanical integrity is underscored by these findings.

Keywords: deposition; interfaces; surfaces; microstructure; corrosion
Corresponding authors: Shubham Sharma, Department of Technical Sciences, Western Caspian University, Baku, Azerbaijan; Centre for Research Impact and Outcome, Chitkara University Institute of Engineering and Technology, Chitkara University, Rajpura 140401, Punjab, India; and Jadara University Research Center, Jadara University, Jordan, E-mail: ; and Shashi Prakash Dwivedi, Department of Mechanical Engineering, Lloyd Institute of Engineering & Technology, Knowledge Park II, Greater Noida, Uttar Pradesh 201306, India, E-mail:

  1. Research ethics: Not applicable.

  2. Informed consent: Not applicable.

  3. Author contributions: Conceptualization, SPD, SS, AMK, RK, YSB; methodology, SPD, SS, AMK, RK, YSB; formal analysis, SPD, SS, AMK, RK, YSB; investigation, SPD, SS, AMK, RK, YSB; writing – original draft, SPD, SS, AMK, RK, YSB; writing – review and editing, SS, TK, AK, MA; supervision, SS, TK, AK, MA; project administration, SS, TK, AK, MA; funding acquisition, SS, TK, AK, MA. All authors have read and agreed to the published version of the manuscript.

  4. Use of Large Language Models, AI and Machine Learning Tools: None declared.

  5. Conflict of interest: The authors declare no competing interests.

  6. Research funding: The authors extend their appreciation to the Deanship of Scientific Research at King Khalid University (KKU) for funding this research through the Research Group Program Under the Grant Number: (R.G.P.2/517/44).

  7. Data availability: My manuscript has no associate data.

References

[1] A. K. Sharma, S. Aravindhan, and R. Krishnamurthy, “Microwaveglazing of alumina–titania ceramic composite coatings,” Mater. Lett., vol. 50, nos. 5–6, pp. 295–301, 2011. https://doi.org/10.1016/s0167-577x(01)00243-9.Search in Google Scholar

[2] S. Zhou, X. Zeng, H. Qianwu, and S. Huang, “Analysis of crack behavior for Ni-based WC composite coatings by lasercladding and crack-free realization,” Appl. Surf. Sci., vol. 255, no. 5, pp. 1646–1653, 2008. https://doi.org/10.1016/j.apsusc.2008.04.003.Search in Google Scholar

[3] R. C. Leonelli, P. Veronesi, L. Denti, A. Gatto, and L. Iuliano, “Microwave assisted sintering of green metal parts,” J. Mater. Process. Technol., vol. 205, nos. 1–3, pp. 489–496, 2008. https://doi.org/10.1016/j.jmatprotec.2007.11.263.Search in Google Scholar

[4] J. Mateos, J. M. Cuetos, E. Fernandez, and R. Vijande, “Tribological behavior of plasma-sprayed WC coatings with and without laser remelting,” Wear, vol. 239, no. 2, pp. 274–281, 2000. https://doi.org/10.1016/s0043-1648(00)00325-2.Search in Google Scholar

[5] D. Roy Agrawal, J. Cheng, and S. Gedevanishvili, “Full sintering of powdered-metal bodies in a microwave field,” Nature, vol. 339, pp. 668–670, 1999. https://doi.org/10.1038/21390.Search in Google Scholar

[6] A. Mondal, A. Upadhyaya, and D. Agrawal, “Microwave sintering of refractory metals/alloys,” J. Microw. Power Electromagn. Energy, vol. 44, no. 1, pp. 28–44, 2009. https://doi.org/10.1080/08327823.2010.11689768.Search in Google Scholar PubMed

[7] D. Gupta, A. K. Sharma, P. M. Bhovi, and S. Dutta, “Development and characterization of microwave composite cladding,” J. Manuf. Process., vol. 14, no. 3, pp. 243–249, 2012. https://doi.org/10.1016/j.jmapro.2012.05.007.Search in Google Scholar

[8] M. Tlotleng, E. Akinlabi, M. Shukla, and S. Pityana, “Microstructure, hardness and bioactivity of hydroxyapatite coatings deposited by direct laser melting process,” Mater. Sci. Eng. C, vol. 43, pp. 189–198, 2014. https://doi.org/10.1016/j.msec.2014.06.032.Search in Google Scholar PubMed

[9] S. P. Dwivedi, S. Sharma, and S. Sharma, “Identification of microwave radiation effect on copper welded joint with brass as filler material using response surface methodology,” Mater. Perform. Charact., vol. 9, no. 1, pp. 267–276, 2020. https://doi.org/10.1520/mpc20190253.Search in Google Scholar

[10] S. P. Dwivedi, S. Sharma, T. Singh, and N. Kumar, “Mechanical and metallurgical characterization of copper-based welded joint using brass as filler metal developed by microwave technique,” Ann. Chimie Sci. Matériaux, vol. 44, pp. 281–286, 2020. https://doi.org/10.18280/acsm.440407.Search in Google Scholar

[11] B. Singh and S. Zafar, “Microwave cladding for slurry erosion resistance applications: a review,” Mater. Today: Proc., vol. 46, no. 7, pp. 2686–2690, 2021. https://doi.org/10.1016/j.matpr.2021.02.371.Search in Google Scholar

[12] C. D. Prasad, M. S. Lingappa, S. Joladarashi, M. R. Ramesh, and B. Sachin, “Characterization and sliding wear behavior of CoMoCrSi + flyash composite cladding processed by microwave irradiation,” Mater. Today: Proc., vol. 46, no. 7, pp. 2387–2391, 2021. https://doi.org/10.1016/j.matpr.2021.01.156.Search in Google Scholar

[13] B. Singh and S. Zafar, “Understanding time-temperature characteristics in microwave cladding,” Manuf. Lett., vol. 25, pp. 75–80, 2020. https://doi.org/10.1016/j.mfglet.2020.08.002.Search in Google Scholar

[14] J. S. Vishwanatha, A. M. Hebbale, N. Kumar, M. S. Srinath, and R. I. Badiger, “ANOVA studies and control factors effect analysis of cobalt based microwave clad,” Mater. Today: Proc., vol. 46, no. 7, pp. 2409–2413, 2021. https://doi.org/10.1016/j.matpr.2021.01.214.Search in Google Scholar

[15] K. P. Kumar, A. Mohanty, M. Shashank Lingappa, M. S. Srinath, and S. K. Panigrahi, “Enhancement of surface properties of austenitic stainless steel by nickel based alloy cladding developed using microwave energy technique,” Mater. Chem. Phys., vol. 256, p. 123657, 2020. https://doi.org/10.1016/j.matchemphys.2020.123657.Search in Google Scholar

[16] B. Singh and S. Zafar, “Influence of post clad heat treatment on microstructure and slurry erosion characteristics of Ni-based microwave clad,” Vacuum, vol. 184, p. 109946, 2021. https://doi.org/10.1016/j.vacuum.2020.109946.Search in Google Scholar

[17] T. K. Mishra, A. Kumar, and S. K. Sinha, “Investigation of sliding wear behaviour of Ni-WC microwave cladding,” Mater. Today: Proc., vol. 26, no. 2, pp. 1418–1422, 2020. https://doi.org/10.1016/j.matpr.2020.02.294.Search in Google Scholar

[18] A. Babu, H. S. Arora, H. Singh, and H. S. Grewal, “Microwave synthesized composite claddings with enhanced cavitation erosion resistance,” Wear, vol. 422–423, pp. 242–251, 2019. https://doi.org/10.1016/j.wear.2019.01.072.Search in Google Scholar

[19] R. B. Nair, H. S. Arora, A. V. Boyana, P. Saiteja, and H. S. Grewal, “Tribological behavior of microwave synthesized high entropy alloy claddings,” Wear, vol. 436–437, p. 203028, 2019. https://doi.org/10.1016/j.wear.2019.203028.Search in Google Scholar

[20] S. Zafar and A. K. Sharma, “Structure-property correlations in nanostructured WC–12Co microwave clad,” Appl. Surf. Sci., vol. 370, pp. 92–101, 2016. https://doi.org/10.1016/j.apsusc.2016.02.114.Search in Google Scholar

[21] A. M. Hebbale and M. S. Srinath, “Microstructural investigation of Ni based cladding developed on austenitic SS-304 through microwave irradiation,” J. Mater. Res. Technol., vol. 5, no. 4, pp. 293–301, 2016. https://doi.org/10.1016/j.jmrt.2016.01.002.Search in Google Scholar

[22] S. P. Dwivedi, et al.., “Homogeneity, metallurgical, mechanical, wear, and corrosion behavior of Ni and B4C coatings deposited on 304 stainless steels developed by microwave cladding technique,” J. Mater. Res. Technol., vol. 27, pp. 5854–5867, 2023. https://doi.org/10.1016/j.jmrt.2023.10.202.Search in Google Scholar

[23] S. P. Dwivedi and S. Sharma, “Synthesis of high entropy alloy AlCoCrFeNiCuSn reinforced AlSi7Mg0.3 based composite developed by solid state technique,” Mater. Lett., vol. 355, p. 135556, 2024. https://doi.org/10.1016/j.matlet.2023.135556.Search in Google Scholar
Received: 2024-03-09
Accepted: 2025-01-18
Published Online: 2025-02-17
Published in Print: 2025-04-28

© 2025 Walter de Gruyter GmbH, Berlin/Boston

Articles in the same Issue

  1. Frontmatter
  2. Atomic, Molecular & Optical Physics
  3. Quantum chemical concept of oxidation states
  4. Dynamical Systems & Nonlinear Phenomena
  5. Comparative study of novel solitary wave solutions with unveiling bifurcation and chaotic structure modelled by stochastic dynamical system
  6. Fundamental Concepts of Physical Science
  7. Fermi motion in nucleons and the generalized Heisenberg uncertainty relation
  8. Hydrodynamics & Plasma Physics
  9. Stability and convection in compressible partially ionized plasma layers: nonlinear and linear analysis
  10. Solid State Physics & Materials Science
  11. Effective medium theory of a concentric metamaterial bifunctional cloak
  12. Morphological impact on energy storage properties of 2D-MoS2 and its nanocomposites: a comprehensive review
  13. Exploring the implications of CoCrFeNiCu high entropy alloy coatings on tribomechanical, wetting behavior, and interfacial microstructural characterizations in microwave-clad AISI 304 stainless steels
https://doi.org/10.1515/zna-2024-0054
Keywords for this article
deposition; interfaces; surfaces; microstructure; corrosion

Articles in the same Issue

  1. Frontmatter
  2. Atomic, Molecular & Optical Physics
  3. Quantum chemical concept of oxidation states
  4. Dynamical Systems & Nonlinear Phenomena
  5. Comparative study of novel solitary wave solutions with unveiling bifurcation and chaotic structure modelled by stochastic dynamical system
  6. Fundamental Concepts of Physical Science
  7. Fermi motion in nucleons and the generalized Heisenberg uncertainty relation
  8. Hydrodynamics & Plasma Physics
  9. Stability and convection in compressible partially ionized plasma layers: nonlinear and linear analysis
  10. Solid State Physics & Materials Science
  11. Effective medium theory of a concentric metamaterial bifunctional cloak
  12. Morphological impact on energy storage properties of 2D-MoS2 and its nanocomposites: a comprehensive review
  13. Exploring the implications of CoCrFeNiCu high entropy alloy coatings on tribomechanical, wetting behavior, and interfacial microstructural characterizations in microwave-clad AISI 304 stainless steels
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 9.9.2025 from https://www.degruyterbrill.com/document/doi/10.1515/zna-2024-0054/html
Scroll to top button