Effect of particles on tensile and bending properties of jute epoxy composites
-
Hamit Adin
and
Mehmet Şükrü Adin
Mehmet Şükrü Adin is a PhD candidate of the Department of Mechanical Engineering, University of Batman, Batman, Turkey. He received his master’s degree in Mechanical Engineering from the University of Batman in 2016. His research interests include adhesive joints, composite materials, welding technology and alternative fuels.
Abstract
In this investigation, mechanical properties of composite materials produced from woven jute type were investigated. These composites were produced in the form of epoxy adhesive layers by using hand lay-up method in which aluminum, mica and ceramic particles were added into epoxy as a structural adhesive by 2, 4 and 6 wt%. Samples produced according to ASTM D procedures were subjected to tensile and three point bending loads to examine the effect of the particles. Experimental results were presented in tables and graphs. As a result, it was observed that the tensile and bending failure loads of the composite materials obtained by using the particle reinforced adhesive increased. Also, the biggest rise in tensile strength was achieved with 4 wt% aluminum and the biggest increase in bending strength was observed for 2 wt% aluminum particles.
About the author
Mehmet Şükrü Adin is a PhD candidate of the Department of Mechanical Engineering, University of Batman, Batman, Turkey. He received his master’s degree in Mechanical Engineering from the University of Batman in 2016. His research interests include adhesive joints, composite materials, welding technology and alternative fuels.
-
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: None declared.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
References
[1] M. Jawaid, H. P. S. A. Khalil, and A. Abu Bakar, “Woven hybrid composites: tensile and flexural properties of oil palm-woven jute fibres based epoxy composites,” Mater. Sci. Eng., vol. 528, no. 15, pp. 5190–5195, 2011, https://doi.org/10.1016/j.msea.2011.03.047.Search in Google Scholar
[2] K. S. Ahmed and S. Vijayarangan, “Tensile, flexural and interlaminar shear properties of woven jute and jute-glass fabric reinforced polyester composites,” J. Mater. Process. Technol., vol. 207, nos. 1–3, pp. 330–335, 2008, https://doi.org/10.1016/j.jmatprotec.2008.06.038.Search in Google Scholar
[3] V. Mishra and S. Biswas, “Physical and mechanical properties of bi-directional jute fiber epoxy composites,” Procedia Eng., vol. 51, pp. 561–566, 2013, https://doi.org/10.1016/j.proeng.2013.01.079.Search in Google Scholar
[4] A. Gopinath, M. S. Kumar, and A. Elayaperumal, “Experimental investigations on mechanical properties of jute fiber reinforced composites with polyester and epoxy resin matrices,” Procedia Eng., vol. 97, pp. 2052–2063, 2014, https://doi.org/10.1016/j.proeng.2014.12.448.Search in Google Scholar
[5] O. A. Khondker, U. S. Ishiaku, A. Nakai, and H. Hamada, “Fabrication and mechanical properties of unidirectional jute/PP composites using jute yarns by film stacking method,” J. Polym. Environ., vol. 13, no. 2, pp. 115–126, 2005, https://doi.org/10.1007/s10924-005-2943-y.Search in Google Scholar
[6] N. Venkateshwaran and A. ElayaPerumal, “Mechanical and water absorption properties of woven jute/banana hybrid composites,” Fibers Polym., vol. 13, no. 7, pp. 907–914, 2012, https://doi.org/10.1007/s12221-012-0907-0.Search in Google Scholar
[7] J. A. Khan, M. A. Khan, and R. Islam, “Effect of mercerization on mechanical, thermal and degradation characteristics of jute fabric-reinforced polypropylene composites,” Fibers Polym., vol. 13, no. 10, pp. 1300–1309, 2012, https://doi.org/10.1007/s12221-012-1300-8.Search in Google Scholar
[8] R. Gujjala, S. Ojha, S. K. Acharya, and S. K. Pal, “Mechanical properties of woven jute-glass hybrid-reinforced epoxy composite,” J. Compos. Mater., vol. 48, no. 28, pp. 3445–3455, 2014, https://doi.org/10.1177/0021998313501924.Search in Google Scholar
[9] K. Sever, “The improvement of mechanical properties of jute fiber/LDPE composites by fiber surface treatment,” J. Reinforc. Plast. Compos., vol. 29, no. 13, pp. 1921–1929, 2010, https://doi.org/10.1177/0731684409339078.Search in Google Scholar
[10] B. Sutharson, M. Rajendran, S. Devadasan, and B. Selvam, “Effect of chemical treatments on mechanical properties of jute fiber hybrid composite laminates,” ARPN J. Eng. Appl. Sci., vol. 7, no. 6, pp. 760–765, 2012.Search in Google Scholar
[11] R. A. Khan, H. U. Zaman, M. A. Khan, et al.., “Effect of the incorporation of PVC on the mechanical properties of the jute-reinforced LLDPE composite,” Polym. Plast. Technol. Eng., vol. 49, no. 7, pp. 707–712, 2010, https://doi.org/10.1080/03602551003749544.Search in Google Scholar
[12] N. M. Mehta and P. H. Parsania, “Fabrication and evaluation of some mechanical and electrical properties of jute-biomass based hybrid composites,” J. Appl. Polym. Sci., vol. 100, no. 3, pp. 1754–1758, 2006, https://doi.org/10.1002/app.23014.Search in Google Scholar
[13] S. Biswas, S. Shahinur, M. Hasan, and Q. Ahsan, “Physical, mechanical and thermal properties of jute and bamboo fiber reinforced unidirectional epoxy composites,” Procedia Eng., vol. 105, pp. 933–939, 2015, https://doi.org/10.1016/j.proeng.2015.05.118.Search in Google Scholar
[14] T. M. Gowda, A. C. B. Naidu, and R. Chhaya, “Some mechanical properties of untreated jute fabric-reinforced polyester composites,” Compos. Part A-Appl. Sci. Manuf., vol. 30, no. 3, pp. 277–284, 1999, https://doi.org/10.1016/S1359-835x(98)00157-2.Search in Google Scholar
[15] M. J. Miah, F. Ahmed, A. Hossain, A. H. Khan, and M. A. Khan, “Study on mechanical and dielectric properties of jute fiber reinforced low-density polyethylene (LDPE) composites,” Polym. Plast. Technol. Eng., vol. 44, nos. 8–9, pp. 1443–1456, 2005, https://doi.org/10.1081/200048718.Search in Google Scholar
[16] M. R. Hossain, M. A. Islam, A. Van Vuurea, and I. Verpoest, “Tensile behavior of environment friendly jute epoxy laminated composite, 5th Bsme international conference on thermal engineering,” Procedia Eng., vol. 56, pp. 782–788, 2013, https://doi.org/10.1016/j.proeng.2013.03.196.Search in Google Scholar
[17] K. Büyükkaya, “Investigation of mechanical behavior of nettle filled hybrid composites of nettle fiber-hazelnut shell,” Gazi Univ. fen Bilim. Derg. Part C: Tasarım ve Teknoloji, vol. 5, no. 4, pp. 133–144, 2017, https://doi.org/10.29109/http-gujsc-gazi-edu-tr.337247.Search in Google Scholar
[18] M. I. Reddy, M. A. Kumar, and C. R. B. Raju, “Tensile and flexural properties of jute, pineapple leaf and glass fiber reinforced polymer matrix hybrid composites,” Mater. Today Proc., vol. 5, no. 1, pp. 458–462, 2018, https://doi.org/10.1016/j.matpr.2017.11.105.Search in Google Scholar
[19] G. Seshanandan, D. Ravindran, and T. Sornakumar, “Mechanical properties of nano titanium oxide particles - hybrid jute-glass FRP composites,” Mater. Today Proc., vol. 3, no. 6, pp. 1383–1388, 2016, https://doi.org/10.1016/j.matpr.2016.04.019.Search in Google Scholar
[20] M. F. Hossen, S. Hamdan, M. R. Rahman, et al.., “Effect of clay content on the morphological, thermo-mechanical and chemical resistance properties of propionic anhydride treated jute fiber/polyethylene/nanoclay nanocomposites,” Measurement, vol. 90, pp. 404–411, 2016, https://doi.org/10.1016/j.measurement.2016.05.006.Search in Google Scholar
[21] K. Deepak, S. V. P. Vattikuti, and B. Venkatesh, “Experimental investigation of jute fiberreinforcednanoclay composite,” Procedia Mater. Sci., vol. 10, pp. 238–242, 2015, https://doi.org/10.1016/j.mspro.2015.06.046.Search in Google Scholar
[22] K. Roy, S. C. Debnath, A. Das, G. Heinrich, and P. Potiyaraj, “Exploring the synergistic effect of short jute fiber and nanoclay on the mechanical, dynamic mechanical and thermal properties of natural rubber composites,” Polym. Test., vol. 67, pp. 487–493, 2018, https://doi.org/10.1016/j.polymertesting.2018.03.032.Search in Google Scholar
[23] T. K. Patnaik and S. S. Nayak, “Physical and thermo-mechanical analysis of marble dust filled needle punch nonwoven jute epoxy composites,” Int. J. Eng. Trends Technol., vol. 49, no. 1, pp. 1–4, 2017, https://doi.org/10.14445/22315381/IJETT-V49P201.Search in Google Scholar
[24] V. Mahajan, V. S. Aher, and R. Katore, “Fabrication of jute-PP and wood stock-PP composites and comparison of their physico-mechanical properties,” IOSR J. Eng., vol. 4, pp. 29–35, 2014, https://doi.org/10.9790/3021-04732935.Search in Google Scholar
[25] A. Jabbar, J. Militky, J. Wiener, B. M. Kale, U. Ali, and S. Rwawiire, “Nanocellulose coated woven jute/green epoxy composites: characterization of mechanical and dynamic mechanical behavior,” Compos. Struct., vol. 161, pp. 340–349, 2017, https://doi.org/10.1016/j.compstruct.2016.11.062.Search in Google Scholar
[26] M. G. Thomas, E. Abraham, P. Jyotishkumar, H. J. Maria, L. A. Pothen, and S. Thomas, “Nanocelluloses from jute fibers and their nanocomposites with natural rubber: preparation and characterization,” Int. J. Biol. Macromol., vol. 81, pp. 768–777, 2015, https://doi.org/10.1016/j.ijbiomac.2015.08.053.Search in Google Scholar PubMed
[27] A. Sharma and A. Patnaik, “Experimental investigation on mechanical and thermal properties of marble dust particulate-filled needle-punched nonwoven jute fiber/epoxy composite,” Metal Polym. Matrix Compos., vol. 70, no. 7, pp. 1284–1288, 2018, https://doi.org/10.1007/s11837-018-2828-x.Search in Google Scholar
[28] P. A. Prasob and M. Sasikumar, “Static and dynamic behavior of jute/epoxy composites with ZnO and TiO2 fillers at different temperature conditions,” Polym. Test., vol. 69, pp. 52–62, 2018, https://doi.org/10.1016/j.polymertesting.2018.04.040.Search in Google Scholar
[29] S. Eksi, K. Genel, A. O. Kapti, and K. Acar, “Bending and lateral crushing behavior of a GFRP and PA6 reinforced aluminum square tube,” Mater. Test., vol. 60, no. 6, pp. 591–599, 2018, https://doi.org/10.3139/120.111194.Search in Google Scholar
[30] J. E. Hoffmann, M. T. Schmitt, D. Eifler, T. Beck, P. Klär, and M. Saumer, “Bending deformation and indentation hardness of electrochemically deposited nanocrystalline nickel-iron alloys,” Mater. Test., vol. 60, no. 11, pp. 1041–1049, 2018, https://doi.org/10.3139/120.111259.Search in Google Scholar
[31] D. Gronych, A. Auhorn, I. Beck, V. Schulze, and D. Lohe, “Influence of surface defects and edge geometry on the bending strength of slip-cast ZrO2 micro-specimens,” Mater. Test., vol. 95, no. 6, pp. 551–558, 2004, https://doi.org/10.3139/146.017989.Search in Google Scholar
[32] I. A. Akpinar, K. Gultekin, S. Akpinar, H. Akbulut, and A. Ozel, “Experimental analysis on the single -lap joints bonded by a nanocomposite adhesives which obtained by adding nanostructures,” Compos. B Eng., vol. 110, pp. 420–428, 2017, https://doi.org/10.1016/j.compositesb.2016.11.046.Search in Google Scholar
[33] I. A. Akpinar, K. Gultekin, S. Akpinar, H. Akbulut, and A. Ozel, “Research on strength of nanocomposite adhesively bonded composite joints,” Compos. B Eng., vol. 126, pp. 143–152, 2017, https://doi.org/10.1016/j.compositesb.2017.06.016.Search in Google Scholar
[34] S. Citil, “Experimental and numerical investigation of adhesively bonded curved lap joints under three-point bending,” Mechanika, vol. 24, no. 6, pp. 824–832, 2018, https://doi.org/10.5755/j01.mech.24.6.22472.Search in Google Scholar
[35] L. L. Zhai, G. P. Ling, J. Li, and Y. W. Wang, “The effect of nanoparticles on the adhesion of epoxy adhesive,” Mater. Lett., vol. 60, no. 25–26, pp. 3031–3033, 2006, https://doi.org/10.1016/j.matlet.2006.02.038.Search in Google Scholar
[36] O. Y. Bozkurt, “Hybridization effects on tensile and bending behavior of aramid/basalt fiber reinforced epoxy composites,” Polym. Compos., vol. 38, no. 6, pp. 1144–1150, 2017, https://doi.org/10.1002/pc.23677.Search in Google Scholar
[37] S. Eksi and K. Genel, “Bending response of hybrid composite tubular beams,” Thin-Walled Struct., vol. 73, pp. 329–336, 2013, https://doi.org/10.1016/j.tws.2013.09.001.Search in Google Scholar
© 2022 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- Effect of water absorption and hydroxyapatite addition on mechanical and microstructural properties of dental luting cements
- Mechanical properties and corrosion behavior of a friction stir processed magnesium alloy composite AZ31B–SiC
- Multi-objective optimization of build orientation considering support structure volume and build time in laser powder bed fusion
- Fatigue properties and crack growth behavior of 7N01 and 6N01 aluminum alloys
- Surface roughness prediction of wire electric discharge machining (WEDM)-machined AZ91D magnesium alloy using multilayer perceptron, ensemble neural network, and evolving product-unit neural network
- Effect of FeTi-FeB inoculation on the shape of carbide reinforcements in hypoeutectic high chromium white cast iron
- Development of an eutectic-based self-healing in Al–Si cast alloy
- Effect of process parameters on mechanical properties of additive manufactured SMP structures based on FDM
- Effect of calcination and sintering temperature on porosity and microstructure of porcelain tiles
- Effect of particles on tensile and bending properties of jute epoxy composites
- Effect of cutting parameters on the machinability of X37CrMoV5-1 hot work tool steel
- Cutting forces during drilling of a SiCp reinforced Al-7075 matrix composite
- Modeling and simulation of tensile properties of r-LDPE/GSF composite using the response surface methododology
- Machinability of alloy ductile iron and forged 16MnCr5 steel
Articles in the same Issue
- Frontmatter
- Effect of water absorption and hydroxyapatite addition on mechanical and microstructural properties of dental luting cements
- Mechanical properties and corrosion behavior of a friction stir processed magnesium alloy composite AZ31B–SiC
- Multi-objective optimization of build orientation considering support structure volume and build time in laser powder bed fusion
- Fatigue properties and crack growth behavior of 7N01 and 6N01 aluminum alloys
- Surface roughness prediction of wire electric discharge machining (WEDM)-machined AZ91D magnesium alloy using multilayer perceptron, ensemble neural network, and evolving product-unit neural network
- Effect of FeTi-FeB inoculation on the shape of carbide reinforcements in hypoeutectic high chromium white cast iron
- Development of an eutectic-based self-healing in Al–Si cast alloy
- Effect of process parameters on mechanical properties of additive manufactured SMP structures based on FDM
- Effect of calcination and sintering temperature on porosity and microstructure of porcelain tiles
- Effect of particles on tensile and bending properties of jute epoxy composites
- Effect of cutting parameters on the machinability of X37CrMoV5-1 hot work tool steel
- Cutting forces during drilling of a SiCp reinforced Al-7075 matrix composite
- Modeling and simulation of tensile properties of r-LDPE/GSF composite using the response surface methododology
- Machinability of alloy ductile iron and forged 16MnCr5 steel
