Investigation of the adhesive strength in a combined compaction and back-injection process to produce back-injected self-reinforced composites (SRCs)
-
Fabian Jakob
,
Marcel Gothe
Abstract
This publication investigates the adhesion between an injection molded component and a self-reinforced composite (SRC) produced in a combined compaction and back-injection process to produce back-injected self-reinforced composites. To study the influence of the process, the parameters barrel temperature, time of injection, and tool temperature were varied. In addition, samples were taken at different positions along the flow path. In light of the orthotropic material behavior of SRCs, investigations were conducted to see whether different loading cases lead to different mechanical behavior. Shear-off and pull-off tests revealed a different strength as a function of the loading type. In the shear-off tests, a mean strength of 11.37 MPa was recorded over the entire test series, while the measured mean strength in the pull-off tests is considerably lower, 4.04 MPa. The type of failure is determined with the aid of SEM images, and the influence of the microstructure of the thermoplastic fibre materials on the adhesion is set out. It is shown that, as of a sufficiently high level of adhesion, failure occurs within the fibres.
-
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: None declared.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
References
Alcock, B. (2004). Single polymer composites based on polypropylene: processing and properties, Doctoral dissertation, Queen Mary University of London, London.Suche in Google Scholar
Aurrekoetxea, J., Castillo, G., Cortes, F., Sarrionandia, M.A., and Urrutibeascoa, I. (2006). Failure of multimaterial fusion bonding interface generated during over-injection molding/thermoforming hybrid process. J. Appl. Polym. Sci. 102: 261–265, https://doi.org/10.1002/app.23696.Suche in Google Scholar
Biermann, D., Gausemeier, J., Heim, H.-P., Hess, S., Peters, G., Ries, A., and Wagner, T. (2015). Planning and optimisation of manufacturing process chains for functionally graded components—part 2: case study on self-reinforced thermoplastic composites. Prod. Eng. Res. Devel. 9: 405–416, https://doi.org/10.1007/s11740-015-0610-2.Suche in Google Scholar
Biermann, D., Gausemeier, J., Heim, H.-P., Hess, S., Petersen, M., Ries, A., and Wagner, T. (2012). Computer-aided planning and optimisation of manufacturing processes for funktional graded components. In: Heim, H.-P., Biermann, D., and Maier, H. (Eds.). 1st International conference on thermo-mechanically graded materials. Verlag Wissenschaftliche Scripten, Auerbach, pp. 195–200.Suche in Google Scholar
Ehrenstein, G. (1999). Polymerwerkstoffe. Struktur, Eigenschaften, Anwendung, 2nd ed. Hanser, Munich, Vienna.Suche in Google Scholar
Ehrenstein, G. (2019). Präparation. Unverstärkte, hochgefüllte und verstärkte Kunststoffe – Ätzen für Strukturuntersuchungen // Unverstärkte, hochgefüllte und verstärkte Kunststoffe – Ätzen für Strukturuntersuchungen : Erlanger Kunststoff-Schadensanalyse. Hanser, Munich.10.3139/9783446460546Suche in Google Scholar
Friedrich, H. (2017). Leichtbau in der Fahrzeugtechnik. Springer Fachmedien, Wiesbaden.10.1007/978-3-658-12295-9Suche in Google Scholar
Gude, M., Kupfer, R., Krahl, M., Liebsch, A., and Koshukow, W. (2017). Hybridstrukturen für die Großserie. Jahresmagazin Kunststofftechnik 80: 86.Suche in Google Scholar
Heim, H.-P. (Ed.) (2016). Specialized injection molding techniques. William Andrew, Imprint of Elsevier, Oxford.Suche in Google Scholar
Heim, H.-P., Biermann, D., and Homberg, W. (Eds.) (2013). Functionally graded materials in industrial mass production, Vol. 2. Verlag Wissenschaftliche Scripten, Auerbach.Suche in Google Scholar
Heim, H.-P., Rohde, B., and Ries, A. (2012). Influence of the process conditions on the morphology–property–relationship of self-reinforced PP-composite. In: Heim, H.-P., Biermann, D., and Maier, H. (Eds.). 1st International conference on thermo-mechanically graded materials. Verlag Wissenschaftliche Scripten, Auerbach, pp. 247–252.Suche in Google Scholar
Jakob, F., Pollmeier, J., and Heim, H.-P. (2021). Process influences in the combined compacting and back-injection process to produce back-injected self-reinforced composites (SRCs) – analysis via multiple regression modelling. Int. Polym. Proc. 36: 608–619, https://doi.org/10.1515/ipp-2020-4105.Suche in Google Scholar
Jerpdal, L., Schuette, P., Ståhlberg, D., and Åkermo, M. (2020). Influence of temperature during overmolding on the tensile modulus of self‐reinforced poly(ethylene terephthalate) insert. J. Appl. Polym. Sci. 137: 48334, https://doi.org/10.1002/app.48334.Suche in Google Scholar
Kmetty, A., Bárány, T., and Karger-Kocsis, J. (2010). Self-reinforced polymeric materials: a review. Prog. Polym. Sci. 35: 1288–1310, https://doi.org/10.1016/j.progpolymsci.2010.07.002.Suche in Google Scholar
Paßmann, D. (2009). Prozessinduzierte Gradierung eigenverstärkter Polypropylen-Faserverbunde beim Heißkompaktieren und Umformen, PPH ZAPOL Dmochowski. Sobczyk Spółka Jawna, Szczecin.Suche in Google Scholar
Ries, A. (2015). Thermo-mechanische Gradierung eigenverstärkter polypropylen-composite. Kassel University Press, Kassel.Suche in Google Scholar
Ries, A. (2021). Structural description of self‐reinforced polypropylene composites. J. Appl. Polym. Sci. 138: 51215, https://doi.org/10.1002/app.51215.Suche in Google Scholar
Rohde, B., Wibbeke, A., Heim, H.-P., and Schöppner, V. (2014). The manufacture of hot-compacted layered composite systems made of oriented semifinished PP-films. ISRN Polym. Sci. 2014: 1–9, https://doi.org/10.1155/2014/601741.Suche in Google Scholar
Schimanski, T. (2002). High-performance polypropylene structures for eco-friendly, fully recyclable composites. Dissertation.Suche in Google Scholar
Schöppner, V., Heim, H.-P., Wibbeke, A., Ries, A., and Rohde, B. (2013). Graded structures in polymers. In: Homberg, W., Biermann, D., and Heim, H.-P. (Eds.). Functionally graded Materials in industrial mass production. Fundamentals. Verlag Wissenschaftliche Scripten, Auerbach, pp. 11–42.Suche in Google Scholar
Schuck, M. (2009). Kompatibilitätsprinzipien beim Montagespritzgießen. Technische Fakultät Uni Erlangen-Nürnberg, Erlangen-Nürnberg.Suche in Google Scholar
Ward, I. and Hine, P. (2004). The science and technology of hot compaction. Polymer 45: 1413–1427, https://doi.org/10.1016/j.polymer.2003.11.050.Suche in Google Scholar
Zimnol, R., Lutter, F., Malek, T., and Arping, T. (2012). Chancen der Organoblech-Hybridtechnik im Leichtbau. ATZ Automobiltech Z. 114: 210–215, https://doi.org/10.1365/s35148-012-0289-z.Suche in Google Scholar
© 2022 Walter de Gruyter GmbH, Berlin/Boston
Artikel in diesem Heft
- Frontmatter
- Research Articles
- Influences on the mechanical properties of SRCs in a combined compacting and back injecting process
- Static, fatigue and stress-shielding analysis of the use of different PEEK based materials as hip stem implants
- Numerical simulation and experimental analysis for evaluating warpage of a 3D thin-walled polymeric part using the injection compression molding process
- A molecular dynamics study on the mechanical properties of defective CNT/epoxy nanocomposites using static and dynamic deformation approaches
- Microstructural, functional groups and textural analysis of expanded polyethylene reinforced polystyrene composites with recycled aluminium as ternary component
- Investigation of the adhesive strength in a combined compaction and back-injection process to produce back-injected self-reinforced composites (SRCs)
- Extraction and characterization of Alfa fibers and their use to produce Alfa/wool woven fabrics for composite reinforcement
- Effect of rubber reinforcement with filler on extrusion flow and extrudate swell
- News
- PPS News
Artikel in diesem Heft
- Frontmatter
- Research Articles
- Influences on the mechanical properties of SRCs in a combined compacting and back injecting process
- Static, fatigue and stress-shielding analysis of the use of different PEEK based materials as hip stem implants
- Numerical simulation and experimental analysis for evaluating warpage of a 3D thin-walled polymeric part using the injection compression molding process
- A molecular dynamics study on the mechanical properties of defective CNT/epoxy nanocomposites using static and dynamic deformation approaches
- Microstructural, functional groups and textural analysis of expanded polyethylene reinforced polystyrene composites with recycled aluminium as ternary component
- Investigation of the adhesive strength in a combined compaction and back-injection process to produce back-injected self-reinforced composites (SRCs)
- Extraction and characterization of Alfa fibers and their use to produce Alfa/wool woven fabrics for composite reinforcement
- Effect of rubber reinforcement with filler on extrusion flow and extrudate swell
- News
- PPS News
