Startseite Investigation of the Temperature Effect on the Electrical Parameters of a Photovoltaic Module at Ouargla City
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Investigation of the Temperature Effect on the Electrical Parameters of a Photovoltaic Module at Ouargla City

  • Narimane Khelfaoui ORCID logo EMAIL logo , Ahmed Djafour , Khadidja Bouali , Mohamed Bilal Danoune , Abdelmoumon Gougui und Halima Boutelli
Veröffentlicht/Copyright: 22. August 2019

Abstract

To predict the I-V characteristics of the photovoltaic module, five parameters photovoltaic model Abstract: To predict the I-V characteristics of the photovoltaic module, five parameters photovoltaic model was utilized. The most influential parameters in the photovoltaic module are the solar irradiance level (E) and the temperature (T). The present research was conducted due to the high-temperature values in Ouargla city (can reach 60 °C in the hot season), which will affect remarkably the installed PV installations in this region. The experimental was done in several days cause the investigation need a constant irradiance values with different temperature. The temperature of a photovoltaic module varies according to other conditions, the temperature measurements made on the rear face of the PV module may not be indicative due to a temperature gradient in the material of the rear face of the module. Unfortunately, photovoltaic systems manufacturers do not take into consideration these environmental circumstances which negatively influence the module parameters and yielded deterioration in the system efficiency. The aim of this paper is to investigate the effect of the temperature term on the electrical performances such as the open circuit voltage (Voc), short circuit current (Isc), optimal power (Pm) and Fill Factor. The temperature distribution is non-uniform temperature on the surface of PV modules joined to that of the quality of temperature measurements affects the values of temperature coefficients found. To validate a model allows the researcher to get approximately the I-V characteristic similar to the experiment values. It use the conventional technique (Newton Raphson method) and it was compared by an artificial intelligent method which is the PSO technique, the five parameters estimated (Iph, Is, Rs, Rp, n). This proposed approach can be utilized to model any marketable PV module based on given datasheet parameters only. Statistical indicators were adopted to evaluate the performance of the proposed models; where the relative error of the PSO method comes more less the conventional method.

References

[1] Yilmaz U, Kircay A, Borekci S. PV system fuzzy logic MPPT method and PI control as a charge controller. Renewable Sustainable Energy Rev. 2018;81:994–1001.10.1016/j.rser.2017.08.048Suche in Google Scholar

[2] Bag A, Subudhi B, Ray PK. Comparative analysis of sliding mode controller and hysteresis controller for active power filtering in a grid connected PV system. Int J Emerg Electr Power Syst. 2018;19:20170044. DOI: 10.1515/ijeeps-2017-0044Suche in Google Scholar

[3] Lau LC, Lee KT, Mohamed AR. Global warming mitigation and renewable energy policy development from the Kyoto protocol to the Copenhagen Accord—A comment. Renewable Sustainable Energy Rev. 2012;16:5280–4.10.1016/j.rser.2012.04.006Suche in Google Scholar

[4] Al-Waeli AH, Sopiana K, Kazem HA, Chaichan MT. Photovoltaic/Thermal (PV/T) systems: status and future prospects. Renewable Sustainable Energy Rev. 2017;77:109–30.10.1016/j.rser.2017.03.126Suche in Google Scholar

[5] Reisi AR, Moradi MH, Jamasb S. Classification and comparison of maximum power point tracking techniques for the photovoltaic system: a review. Renewable Sustainable Energy Rev. 2013;19:433–43.10.1016/j.rser.2012.11.052Suche in Google Scholar

[6] Mohanty P, Bhuvaneswari G, Balasubramanian R, Dhaliwal NK. MATLAB based modeling to study the performance of different MPPT techniques used for solar PV system under various operating conditions. Renewable Sustainable Energy Rev. 2014;38:581–93.10.1016/j.rser.2014.06.001Suche in Google Scholar

[7] Bouraiou A. Experimental investigation of observed defects in crystalline silicon PV modules under outdoor hot dry climatic conditions in Algeria. Sol Energy. 2018;159:475–87.10.1016/j.solener.2017.11.018Suche in Google Scholar

[8] Hosseini SK. Determination of photovoltaic characteristics in real field conditions. IEEE J Photovoltaics. 2018;8:572–80. DOI: 10.1109/JPHOTOV.2018.2797974Suche in Google Scholar

[9] Villalva MG. Comprehensive approach to modeling and simulation of photovoltaic arrays. IEEE Trans Power Electron. 2009;24:1198–208.10.1109/TPEL.2009.2013862Suche in Google Scholar

[10] Moller HJ. Semiconductors for Solar Cells. Norwood, MA: 76 Artech House, 1993.Suche in Google Scholar

[11] Photovoltaic systems technology. Kassel, Germany: Universitat Kassel, 2003.Suche in Google Scholar

[12] Sampaio PG, González MO, de Vasconcelos RM, dos Santos MA, de Toledo JC, Pereira JP. Photovoltaic technologies: mapping from patent analysis. Renewable Sustainable Energy Rev. 2018;93:215–24.10.1016/j.rser.2018.05.033Suche in Google Scholar

[13] Ogbomo OO. Renewable and sustainable energy reviews, 2016.Suche in Google Scholar

[14] Adinoyi MJ, Said SA. Effect of dust accumulation on the power outputs of solar photovoltaic modules. Renewable Energy. 2013;60:633–6.10.1016/j.renene.2013.06.014Suche in Google Scholar

[15] Durisch W, Bitnar B, Roth F, Palfinger G. Small 6 thermo photovoltaic prototype systems. Solar Energy. 2003;75:11–15.10.1016/S0038-092X(03)00232-9Suche in Google Scholar

[16] Kalogirou SA. The book of solar energy engineering: processes and systems, 2009.Suche in Google Scholar

[17] Fouad MM, Shihata LA, Morgan EI. An integrated review of factors influencing the performance of photovoltaic panels. Renewable Sustainable Energy Rev. 2017;80:1499–511.10.1016/j.rser.2017.05.141Suche in Google Scholar

[18] Said SA, Hassan G, Walwil HM, Al-Aqeeli N. The effect of environmental factors and dust accumulation on photovoltaic modules and dust-accumulation mitigation strategies. Renewable Sustainable Energy Rev. 2018;82:743–60.10.1016/j.rser.2017.09.042Suche in Google Scholar

[19] Djafour A. Modeling of the output characteristic of a photovoltaic module installed at Ouargla. Ann Sci Technol. 2014;6:113–21.10.12816/0039180Suche in Google Scholar

[20] Roberts JJ. Assessment of photovoltaic performance models for system simulation. Renewable Sustainable Energy Rev. 2016. DOI: 10.1016/j.rser.2016.10.022.Suche in Google Scholar

[21] Kumar A. An efficient parameters extraction technique of photovoltaic models for performance assessment. Sol Energy. 2017;158:192–206.10.1016/j.solener.2017.09.046Suche in Google Scholar

[22] Pillai PT. A PV panel model considering temperature and irradiance effect on panel resistances, IEEE International Conference on Technological Advancements in Power and Energy (TAP Energy), 2017.10.1109/TAPENERGY.2017.8397269Suche in Google Scholar

[23] Khayamy M, Ojo O. A power regulation and droop mode control method for a stand-alone load fed from a PV-current source inverter. Int J Emerg Electr Power Syst. 2015;16:83–91.10.1515/ijeeps-2014-0159Suche in Google Scholar

[24] de la Parra I, Muñoz M, Lorenzo E, García M, Marcos J, Martínez-Moreno F. PV performance modelling: A review in the light of quality assurance for large PV plants. Renewable Sustainable Energy Rev. 2017;78:780–97.10.1016/j.rser.2017.04.080Suche in Google Scholar

[25] Ciulla G, Brano VL, DiDio V, Cipriani G. A comparison of different one-diode models for the representation of I–V characteristic of a PV cell. Renewable Sustainable Energy Rev. 2014;32:684–96.10.1016/j.rser.2014.01.027Suche in Google Scholar

[26] Humada AM, Hojabri M, Mekhilef S, Hamada HM. Solar cell parameters extraction based on single and double-diode models: a review. Renewable Sustainable Energy Rev. 2016;56:494–509.10.1016/j.rser.2015.11.051Suche in Google Scholar

[27] Danoune MB, Djafour A, Gougui A, Khelfaoui N, Boutli H. Characterization of photovoltaic panel using single diode and double diode models a comparative study with experimental validation, The 5th International Seminar on New and Renewable Energies, Ghardaïa – Algeria, 24–25 Octobre 2018.Suche in Google Scholar

[28] Jordehi AR. Parameter estimation of solar photovoltaic (PV) cells: a review. Renewable Sustainable Energy Rev. 2016;61:354–71.10.1016/j.rser.2016.03.049Suche in Google Scholar

[29] Bellini A. Simplified model of a photovoltaic module, Conference Paper October 2009 Source: IEEE Xplore.Suche in Google Scholar

[30] Anurag A, Bal S, Sourav S. A comparative study of mathematical modeling of photovoltaic array. Int J Emerg Electr Power Syst. 2014;15:313–26.10.1515/ijeeps-2013-0115Suche in Google Scholar

[31] Amelia AR. Investigation of the effect temperature on photovoltaic (PV) panel output performance. Int J Adv Sci Eng Inf Technol. 2016;6:682–88. DOI: 10.18517/ijaseit.6.5.938.Suche in Google Scholar

[32] Ma J. Parameter estimation of photovoltaic models via Cuckoo search. J Appl Math. 2013. DOI: 10.1155/2013/362619.Suche in Google Scholar

[33] Hassouni BE, Ourahou M, Ayrir W, Haddi A, Amrani AG. A study of efficient MPPT techniques for photovoltaic system using boost converter. Int J Emerg Electr Power Syst. 2018;19:20170180. DOI: 10.1515/ijeeps-2017-0180.Suche in Google Scholar

[34] Anilkumar TT, Nayak PS, Simon SP. Experimental investigation on a prototype solar-wind hybrid system with a Pico hydro turbine. Int J Emerg Electr Power Syst. 2017;18:20160103.10.1515/ijeeps-2016-0103Suche in Google Scholar

[35] Mahammed IH. Modeling of the photovoltaic generator by neuron network at site Ghardaia, The 2nd International conference on New and Renewable Energies, Ghardaïa – Algeria, 15, 16 et 17 October 2012.Suche in Google Scholar

[36] Benkaciali S. Evaluation of the global solar irradiation from the artificial neural network technique. Revue des Energies Renouvelables. 2016;19:617–31.Suche in Google Scholar

[37] Panda KP, Anand A, Bana PR, Panda G. Novel PWM control with modified PSO-MPPT algorithm for reduced switch MLI based standalone PV system. Int J Emerg Electr Power Syst. 2018;19:20180023.10.1515/ijeeps-2018-0023Suche in Google Scholar

[38] Kebir ST. A detailed step-by-step electrical parameters identification method for photovoltaic generators using a combination of two approaches. Adv Sci Technol Eng Syst J. 2018;3:45–52.10.25046/aj030406Suche in Google Scholar

[39] Bana S, Saini RP. Identification of unknown parameters of a single diode photovoltaic model using particle swarm optimization with binary constraints. Renewable Energy. 2016. DOI: 10.1016/j.renene.2016.10.010.Suche in Google Scholar

[40] Gong L. An improved PSO algorithm for high accurate parameter identification of PV model, 2017 IEEE International Conference on Environment and Electrical Engineering and 2017 IEEE Industrial and Commercial Power Systems Europe (EEEIC / I&CPS Europe).10.1109/EEEIC.2017.7977740Suche in Google Scholar

[41] Babatunde AA, Abbasoglu S, Senol M. Analysis of the impact of dust, tilt angle and orientation on the performance of PV plants. Renewable Sustainable Energy Rev. 2018;90:1017–26.10.1016/j.rser.2018.03.102Suche in Google Scholar

[42] Neya I. Study of the influence of temperature on photovoltaic parameters under real operating conditions: master memory in energy genie energy and renewable energy, Laboratory Solar Energy and Energy Saving (LESEE), 2iE, Ouagadougou, Burkina Faso, 28th October 2015.Suche in Google Scholar

[43] Fares MA, Atik L, Ba Chir G, Aill M. Photovoltaic panel and experimental testing, International Conference on Technologies and Materials for Renewable Energy, Environment and Sustainability, Beirut Lebanon, TMREES 17, 21–24 April 2017.Suche in Google Scholar

[44] Necaibia S, Kelaiaia MS, Labar H, Necaibia A. Implementation of an improved incremental conductance MPPT control based boost converter in photovoltaic applications. Int J Emerg Electr Power Syst. 2017;18:20170051.10.1515/ijeeps-2017-0051Suche in Google Scholar

[45] Franco RA. Analytical method for extraction of the single-diode model parameters for photovoltaic panels from datasheet data. Electron Lett. 2018 14;54:519–21. 15.10.1049/el.2018.0402Suche in Google Scholar

[46] Zhang Y. Prediction of I-V characteristics for a PV panel by combining single diode model and explicit analytical model. Sol Energy. 2017;144:349–55.10.1016/j.solener.2017.01.043Suche in Google Scholar

[47] Karki IB. Effect of temperature on the I-V characteristics of a polycrystalline solar cell. J Nepal Phys Soc. 2015;3:35–40. DOI: 10.3126/jnphyssoc.v3i1.14440.Suche in Google Scholar

[48] Malik AQ. Influence of temperature on the performance of photovoltaic polycrystalline silicon module in the bruneian climate. AJSTD. 2010;26:61–72. DOI: 10.29037/ajstd.252.Suche in Google Scholar

[49] Sudhakar Babu T, Prasanth Ram J, Sangeetha K, Laudani A, Rajasekar N. Parameter extraction of two diode solar PV model using Fireworks algorithm. Solar Energy. 2016;140:265–76. DOI: 10.1016/j.solener.2016.10.044.Suche in Google Scholar

Received: 2019-01-23
Revised: 2019-07-24
Accepted: 2019-07-27
Published Online: 2019-08-22

© 2019 Walter de Gruyter GmbH, Berlin/Boston

Heruntergeladen am 29.9.2025 von https://www.degruyterbrill.com/document/doi/10.1515/ijeeps-2019-0025/html
Button zum nach oben scrollen