Development of inexpensive, simple and environment-friendly solar selective absorber using copper nanoparticle
-
Aditi Yerudkar
Abstract
Concentrating solar power is the most challenging and expensive yet highly efficient source of thermal energy from solar power. This is mainly due to the intermittency of the sun rays and expensive materials used to harness its energy. One of the main components adding to the cost is the solar selective absorber materials which are simply put spectrally selective coatings on a receiver system to capture maximum heat from the sun. These materials add to a large extent to the efficiency of converting the sun’s energy to thermal energy and in turn electricity. An ideal solar selective absorber possesses the property of absorbing maximum radiations in the solar spectrum and emit minimum in the thermal energy spectrum. In the current study, an inexpensive, simple and environment-friendly solar selective absorber is fabricated by a galvanic displacement reaction of copper nanoparticles on galvanised metal substrates. These copper nanoparticles have high absorptivity (0.8–0.9) by virtue of plasmon resonance property. The emissivity is low due to the highly reflective metal substrate. By varying size of the copper nanoparticles from 100 nm to 2 μm emissivity and absorptivity can be varied. However, achieving low emissivity and high absorptivity requires some optimising. The size depends on the concentration of precursor solution and immersion time of substrate. One of the remedies for controlling the deposition rate to tune the nanoparticle size and microstructure of deposited copper nanoparticle is by addition of a deposition inhibitor (e.g. Polyethylene glycol).
Funding source: Marathi Vidnyan Parishad
Acknowledgements
The authors would like to thank Marathi Vidnyan Parishad, Chunabhatti, Mumbai for funding this work.
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
Research funding: This work is supported by Marathi Vidnyan Parishad.
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
References
Abbasi-Kesbi, F., A. M. Rashidi, and B. Astinchap. 2018. “Preparation of Ultrafine Grained Copper Nanoparticles via Immersion Deposit Method.” Applied Nanoscience 8 (3): 221–30. https://doi.org/10.1007/s13204-018-0646-7.Search in Google Scholar
Almeco Absorber Surfaces TiNOX. https://www.almecogroup.com/en/pages/479-absorbers (letzter Zugriff January 03, 2021).Search in Google Scholar
Amri, A., Z. T. Jiang, T. Pryor, C.-Y. Yin, and S. Djordjevic. 2014. “Developments in the Synthesis of Flat Plate Solar Selective Absorber Materials via Sol-Gel Methods: A Review.” Renewable and Sustainable Energy Reviews 36: 316–28. https://doi.org/10.1016/j.rser.2014.04.062.Search in Google Scholar
Atkinson, C., C. L. Sansom, H. J. Almond, and C. P. Shaw. 2015. “Coatings for Concentrating Solar Systems – A Review.” Renewable and Sustainable Energy Reviews 45: 113–22. https://doi.org/10.1016/j.rser.2015.01.015.Search in Google Scholar
Cao, F., K. McEnaney, G. Chen, and Z. Ren. 2014. “A Review of Cermet-Based Spectrally Selective Solar Absorbers.” Energy & Environmental Science 7 (5): 1615. https://doi.org/10.1039/c3ee43825b.Search in Google Scholar
Chen, T., M. Pourmand, A. Feizpour, B. Cushman, and B. M. Reinhard. 2013. “Tailoring Plasmon Coupling in Self-Assembled One-Dimensional Au Nanoparticle Chains through Simultaneous Control of Size and Gap Separation.” The Journal of Physical Chemistry Letters 4 (13): 2147–52. https://doi.org/10.1021/jz401066g.Search in Google Scholar PubMed PubMed Central
Chu, S., Y. Cui, and N. Liu. 2016. “The Path towards Sustainable Energy.” Nature Materials 16 (1): 16–22. https://doi.org/10.1038/nmat4834.Search in Google Scholar PubMed
Coluccio, M. L., F. Gentile, M. Francardi, G. Perozziello, N. Malara, P. Candeloro, and E. Di Fabrizio. 2014. “Electroless Deposition and Nanolithography Can Control the Formation of Materials at the Nano-Scale for Plasmonic Applications.” Sensors 14 (4): 6056–83. https://doi.org/10.3390/s140406056.Search in Google Scholar PubMed PubMed Central
Dan, A., H. C. Barshilia, K. Chattopadhyay, and B. Basu. 2017. “Solar Energy Absorption Mediated by Surface Plasma Polaritons in Spectrally Selective Dielectric-Metal-Dielectric Coatings: A Critical Review.” Renewable and Sustainable Energy Reviews 79: 1050–77. https://doi.org/10.1016/j.rser.2017.05.062.Search in Google Scholar
Fasasi, A., P. R. Griffiths, and L. Scudiero. 2011. “Surface-Enhanced Infrared Absorption (SEIRA) of Adsorbates on Copper Nanoparticles Synthesized by Galvanic Displacement.” Applied Spectroscopy 65 (7): 750–5.10.1366/11-06274Search in Google Scholar PubMed
Gawande, M. B., A. Goswami, F. X. Felpin, T. Asefa, X. Huang, R. Silva, X. Zou, R. Zboril, and R. S. Varma. 2016. “Cu and Cu-Based Nanoparticles: Synthesis and Applications in Catalysis.” Chemical Reviews 116 (6): 3722–811. https://doi.org/10.1021/acs.chemrev.5b00482.Search in Google Scholar PubMed
Goldemberg, J. 2001. World Energy Assessment: Energy and the Challenge of Sustainability. New York, USA: United Nations.Search in Google Scholar
González, F., E. Barrera-Calva, L. Huerta, and R. S. Mane. 2011. “Coatings of Fe3O4 Nanoparticles as Selective Solar Absorber.” The Open Surface Science Journal 3 (1): 131–5. https://doi.org/10.2174/1876531901103010131.Search in Google Scholar
Hasegawa, M., Y. Okinaka, Y. Shacham-Diamand, and T. Osaka. 2006. “Void-Free Trench-Filling by Electroless Copper Deposition Using the Combination of Accelerating and Inhibiting Additives.” Electrochemical and Solid-State Letters 9 (8): C138. https://doi.org/10.1149/1.2206008.Search in Google Scholar
Hill, M. R. H., and G. T. Rogers. 1978. “Polyethylene Glycol in Copper Electrodeposition onto a Rotating Disk Electrode.” Journal of Electroanalytical Chemistry and Interfacial Electrochemistry 86 (1): 179–88. https://doi.org/10.1016/S0022-0728(78)80365-9.Search in Google Scholar
Ho, C. K., A. R. Mahoney, A. Ambrosini, M. Bencomo, A. Hall, and T. N. Lambert. 2014. “Characterization of Pyromark 2500 Paint for High-Temperature Solar Receivers.” Journal of Solar Energy Engineering 136 (1): 2014–7. https://doi.org/10.1115/1.4024031.Search in Google Scholar
Kalogirou, S. 2003. “The Potential of Solar Industrial Process Heat Applications.” Applied Energy 76 (4): 337–61. https://doi.org/10.1016/S0306-2619(02)00176-9.Search in Google Scholar
Katumba, G., L. Olumekor, A. Forbes, G. Makiwa, B. Mwakikunga, J. Lu, and E. Wäckelgård. 2008. “Optical, Thermal and Structural Characteristics of Carbon Nanoparticles Embedded in ZnO and NiO as Selective Solar Absorbers.” Solar Energy Materials and Solar Cells 92 (10): 1285–92. https://doi.org/10.1016/j.solmat.2008.04.023.Search in Google Scholar
Kelly, J. J., and A. C. West. 1998. “Copper Deposition in the Presence of Polyethylene Glycol: I. Quartz Crystal Microbalance Study.” Journal of the Electrochemical Society 145 (10): 3472. https://doi.org/10.1149/1.1838829.Search in Google Scholar
Kennedy, C. E. 2002. Review of Mid- to High-Temperature Solar Selective Absorber Materials. United States: National Renewable Energy Laboratory.10.2172/15000706Search in Google Scholar
Lauterbach, C., B. Schmitt, U. Jordan, and K. Vajen. 2012. “The Potential of Solar Heat for Industrial Processes in Germany.” Renewable and Sustainable Energy Reviews 16 (7): 5121–30. https://doi.org/10.1016/j.rser.2012.04.032.Search in Google Scholar
Mandal, J., D. Wang, A. C. Overvig, N. N. Shi, D. Paley, A. Zangiabadi, Q. Cheng, K. Barmak, N. Yu, and Y. Yang. 2017. “Scalable, “Dip-and-Dry” Fabrication of a Wide-Angle Plasmonic Selective Absorber for High-Efficiency Solar–Thermal Energy Conversion.” Advanced Materials 29 (41): 1–9. https://doi.org/10.1002/adma.201702156.Search in Google Scholar PubMed
Markal Pyromark High Temperature Paint. Also available at https://markal.com/products/pyromark-high-temperature-paint?variant=9204789084207.Search in Google Scholar
Mekhilef, S., R. Saidur, and A. Safari. 2011. “A Review on Solar Energy Use in Industries.” Renewable and Sustainable Energy Reviews 15 (4): 1777–90. https://doi.org/10.1016/j.rser.2010.12.018.Search in Google Scholar
Mohsen-Nia, M., H. Rasa, and H. Modarress. 2008. “Liquid–Liquid Equilibria for the Poly (Ethylene Glycol) + Water + Copper Sulfate System at Different Temperatures.” Journal of Chemical & Engineering Data 53 (4): 946–9. https://doi.org/10.1021/je700643u.Search in Google Scholar
Osborn, T., N. Galiba, and P. A. Kohl. 2009. “Electroless Copper Deposition with PEG Suppression for All-Copper Flip-Chip Connections.” Journal of the Electrochemical Society 156 (7): D226. https://doi.org/10.1149/1.3123288.Search in Google Scholar
Oxford. 2018. Oxford Lab Fine Chem LLP. Also available at https://www.oxfordlabfinechem.com/price.pdf.Search in Google Scholar
Patil, R. G., A. N. Yerudkar, A. R. Joglekar, S. V. Panse, V. H. Dalvi, G. S. Shankarling, V. D. Deshpande, A. K. Nayak, and J. B. Joshi. 2020. “Transition Metal Compounds as Solar Selective Material: A Review.” Reviews in Chemical Engineering (forthcoming). https://doi.org/10.1515/revce-2020-0026.10.1515/revce-2020-0026Search in Google Scholar
Pillai, S., and M. A. Green. 2010. “Plasmonics for Photovoltaic Applications.” Solar Energy Materials and Solar Cells 94 (9): 1481–6. https://doi.org/10.1016/j.solmat.2010.02.046.Search in Google Scholar
Schlesinger, M., and M. Paunovic. 2011. Modern Electroplating, 55th ed. Hoboken, New Jersey, USA: John Wiley & Sons.10.1002/9780470602638Search in Google Scholar
Selvakumar, N., and H. C. Barshilia. 2012. “Review of Physical Vapor Deposited (PVD) Spectrally Selective Coatings for Mid- and High-Temperature Solar Thermal Applications.” Solar Energy Materials and Solar Cells 98: 1–23. https://doi.org/10.1016/j.solmat.2011.10.028.Search in Google Scholar
Sharma, A. K., C. Sharma, S. C. Mullick, and T. C. Kandpal. 2017. “Solar Industrial Process Heating: A Review.” Renewable and Sustainable Energy Reviews 78: 124–37. https://doi.org/10.1016/j.rser.2017.04.079.Search in Google Scholar
Song, S.-J., S.-R. Choi, J.-G. Kim, and H.-G. Kim. 2016. “Effect of Molecular Weight of Polyethylene Glycol on Copper Electrodeposition in the Presence of Bis-3-Sulfopropyl-Disulfide.” International Journal of Electrochemical Science 11: 10067–79. https://doi.org/10.20964/2016.12.45.Search in Google Scholar
Sukhatme, S. P., and J. K. Nayak. 2017. Solar Energy, 4th ed. New Delhi, India: McGraw-Hill Education.Search in Google Scholar
Turing, A. M. 1990. “The Chemical Basis of Morphogenesis.” Bulletin of Mathematical Biology 52 (1–2): 153–97. https://doi.org/10.1007/BF02459572.Search in Google Scholar PubMed
Xu, K., M. Du, L. Hao, J. Mi, Q. Yu, and S. Li. 2020. “A Review of High-Temperature Selective Absorbing Coatings for Solar Thermal Applications.” Journal of Materiomics 6 (1): 167–82. https://doi.org/10.1016/j.jmat.2019.12.012.Search in Google Scholar
Yue, Z., B. Cai, L. Wang, X. Wang, and M. Gu. 2016. “Intrinsically Core-Shell Plasmonic Dielectric Nanostructures with Ultrahigh Refractive Index.” Science Advances 2 (3): e1501536. https://doi.org/10.1126/sciadv.1501536.Search in Google Scholar PubMed PubMed Central
© 2021 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- Editorial
- 10.1515/ijcre-2021-0153
- Special Issue Articles
- Gas-liquid downward flow through narrow vertical conduits: effect of angle of entry and tube-diameter on flow patterns
- Liquid antisolvent recrystallization and solid dispersion of flufenamic acid with polyvinylpyrrolidone K-30
- Forced convection heat transfer study of a blunt-headed cylinder in non-Newtonian power-law fluids
- Comparative studies on the separation of endocrine disrupting compounds from aquatic environment by emulsion liquid membrane and hollow fiber supported liquid membrane
- Instabilities of a freely moving spherical particle in a Newtonian fluid: Direct Numerical Simulation
- Numerical simulation of squeezing flow Jeffrey nanofluid confined by two parallel disks with the help of chemical reaction: effects of activation energy and microorganisms
- Development of inexpensive, simple and environment-friendly solar selective absorber using copper nanoparticle
- Effect of contacting pattern and various surfactants on phenol extraction efficiency using emulsion liquid membrane
- Foam drainage enhancement in foam fractionation for dye removal: process optimization by Taguchi methodology and grey relational analysis
- Phase equilibrium in n-octane/water separation units: vapor pressures, vapor and liquid molar fractions
Articles in the same Issue
- Frontmatter
- Editorial
- 10.1515/ijcre-2021-0153
- Special Issue Articles
- Gas-liquid downward flow through narrow vertical conduits: effect of angle of entry and tube-diameter on flow patterns
- Liquid antisolvent recrystallization and solid dispersion of flufenamic acid with polyvinylpyrrolidone K-30
- Forced convection heat transfer study of a blunt-headed cylinder in non-Newtonian power-law fluids
- Comparative studies on the separation of endocrine disrupting compounds from aquatic environment by emulsion liquid membrane and hollow fiber supported liquid membrane
- Instabilities of a freely moving spherical particle in a Newtonian fluid: Direct Numerical Simulation
- Numerical simulation of squeezing flow Jeffrey nanofluid confined by two parallel disks with the help of chemical reaction: effects of activation energy and microorganisms
- Development of inexpensive, simple and environment-friendly solar selective absorber using copper nanoparticle
- Effect of contacting pattern and various surfactants on phenol extraction efficiency using emulsion liquid membrane
- Foam drainage enhancement in foam fractionation for dye removal: process optimization by Taguchi methodology and grey relational analysis
- Phase equilibrium in n-octane/water separation units: vapor pressures, vapor and liquid molar fractions