Startseite Naturwissenschaften 1.2 Classification of adhesives and sealants
Kapitel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

1.2 Classification of adhesives and sealants

  • Matthias Popp und Hartwig Lohse
Weitere Titel anzeigen von Vincentz Network
Formulating Adhesives and Sealants
Ein Kapitel aus dem Buch Formulating Adhesives and Sealants
© 2025 Vincentz Network, Hannover, Germany

© 2025 Vincentz Network, Hannover, Germany

Kapitel in diesem Buch

  1. Frontmatter 1
  2. Preface 5
  3. Contents 7
  4. Part I General basics
  5. 1 Introduction
  6. 1.1 Definitions 11
  7. 1.2 Classification of adhesives and sealants 15
  8. 1.3 Economic significance of adhesives and sealants 20
  9. 1.4 References 22
  10. 2 Adhesion
  11. 2.1 Adhesion forces and mechanisms 23
  12. 2.2 Wetting of substrates 31
  13. 2.3 Improvement of adhesion through pretreatment 40
  14. 2.4 References 44
  15. Part II Adhesives
  16. 1 Physically setting adhesives
  17. 1.1 Solvent-based adhesives and sealants 46
  18. 1.2 Water-based adhesives and sealants 69
  19. 1.3 Hot-melt adhesives 91
  20. 1.4 Plastisols 128
  21. 2 Reactive adhesives
  22. 2.1 Basic principles 133
  23. 2.2 Polyaddition adhesives 140
  24. 2.3 Polymerization adhesives 248
  25. 2.4 Polycondensation adhesives 276
  26. 3 Pressure-sensitive adhesives (PSA)
  27. 3.1 Basic principles 300
  28. 3.2 Pressure-sensitive tapes 303
  29. 3.3 Formulation of the PSA-Compound 308
  30. 3.4 Evaluation of pressure-sensitive adhesives (general) 332
  31. 3.5 New developments 333
  32. 3.6 References 333
  33. Part III Future trends and challenges
  34. 1 Introduction 335
  35. 2 Impact on the adhesives industry
  36. 2.1 Health and environmental protection 335
  37. 2.2 Circular economy 338
  38. 2.3 References 340
  39. Part IV Adhesives and sealants formulation approach
  40. 1 Basic principles
  41. 1.1 Adhesion properties 341
  42. 1.2 Cohesion of adhesives and viscoelasticity 343
  43. 1.3 Thermomechanical properties 345
  44. 1.4 Properties affected by fillers 346
  45. 2 Stress analysis of adhesive joints
  46. 2.1 Preliminary note 356
  47. 2.2 Mechanical loads 356
  48. 2.3 Analysis of ageing influences 362
  49. 2.4 Anisotropic effects 365
  50. 3 Bond design rules and recommendations 366
  51. 4 Testing of adhesive and bonded joints
  52. 4.1 Characterization of adhesives as delivered state 369
  53. 4.2 Testing of adhesive and sealants in the solidified state 373
  54. 4.3 Testing of pressure-sensitive adhesives (PSA) 395
  55. 4.4 References 400
  56. General literature 402
  57. Authors 404
  58. Index 405
Heruntergeladen am 8.9.2025 von https://www.degruyterbrill.com/document/doi/10.1515/9783748606123-003/html
Button zum nach oben scrollen