Volume 15, Issue 2

In the paper the impact of frequency chirp of directly modulated lasers is considered in context of high-speed data transmission over negative dispersion fiber. Chirp/dispersion induced signal distortions are described, and detailed investigations of their influence on 10 Gb/s transmission system performance are presented. The desired laser chirp characteristics and optimal driving conditions are determined. It is also demonstrated that directly modulated laser with low chirp offers similar or even better dispersion tolerance than unchirped (externally modulated) source. Experimental verification of described investigations is presented at the end.

In this work, we present an optoelectronic digital multiplexer 4:1 based on a multipixel nematic liquid crystal cell. This device uses two optical control signals to select one among four possible optical data inputs. These data signals are generated by four red LEDs, which are guided through plastic optical fiber towards liquid crystal pixels. For our purpose, only four pixels of the cell will be used to modulate the optical signal across them. Each pixel will be addressed by a square waveform coming from the conditioning circuit managed by a microcontroller system. The electronic control allows the multiplexer to work as as simple two input logical gates such as AND, NAND, OR, NOR, XOR and XNOR. The operation time of the device is limited by the response time of LC cell that is in the millisecond range.

Infrared reflective collimators are important components of expensive sophisticated test systems used for testing thermal imagers. Too low quality collimators can become a source of significant measurement errors and collimators of too high quality can unnecessarily increase cost of a test system. In such a situation it is important for test system users to know proper requirements on the collimator and to be able to verify its performance. A method for evaluation of infrared reflective collimators used in test systems for testing thermal imagers is presented in this paper. The method requires only easily available optical equipment and can be used not only by collimator manufactures but also by users of test equipment to verify performance of the collimators used for testing thermal imagers.

Optical model, scalar or vectorial one, describing behaviour of an optical field within a diode-laser cavity, is one of the most important parts of modelling of a diode-laser operation. As compared to more accurate vectorial optical approaches, scalar ones are known to be less exact but simultaneously they need much less computation time. Besides, they have been sometimes found to be surprisingly exact even beyond their confirmed range of validity. Therefore, in this paper, real validity limits of their application have been determined by comparing their simplified results with more exact results obtained with the aid of vectorial models. The analysis comprises a comparison of an application of the most popular scalar approach to optical properties of diode lasers, i.e., the effective index method, and the vectorial method of lines for the standard 1.3-µm GaAs-based stripe-geometry diode laser. The scalar model has been found to be quite exact in the case of a determination of the effective refractive index, i.e., the wavelength of emitted radiation, whereas its exactness in the lasing threshold analysis is much worse, especially in the case of higher-order modes. Our analysis is concluded with a determination of the regions where both models give satisfactorily close results.

A pulsed master oscillator fiber power amplifier working in nanosecond range has been developed. An ytterbium-doped double-clad (large mode area) optical fiber was used as an amplifying medium. Actively Q-switched Nd:YVO laser was used as a seed of light pulses. The system worked at the repetition rate from 10 kHz to 40 kHz. At the amplifier output, pulses of 10.9 kW peak-power were achieved. The laser system worked at the slope efficiency of 30%.

Optical diffraction tomography (ODT) applied to measurement of optical microelements is limited by low dynamic range, i.e., only objects with small deviations of refractive-index distribution can be measured. Therefore in this paper the limitations and errors of ODT are investigated throughout extensive numerical experiments. It is shown that these errors can be reduced by introduction of additional numerical focusing in the tomographic reconstruction algorithm. Additionally, new tomographic reconstruction algorithm using back propagation in reference medium for optical microelements measurement with known design is proposed. This hybrid reconstruction algorithm allows significant extension of ODT applicability in measurement of elements having large deviations of refractive-index distribution.

The existing technology for uncooled MWIR photon detectors based on polycrystalline lead salts is stigmatized for being a 50-year-old technology. It has been traditionally relegated to single-element detectors and relatively small linear arrays due to the limitations imposed by its standard manufacture process based on a chemical bath deposition technique (CBD) developed more than 40 years ago. Recently, an innovative method for processing detectors, based on a vapour phase deposition (VPD) technique, has allowed manufacturing the first 2D array of polycrystalline PbSe with good electro optical characteristics. The new method of processing PbSe is an all silicon technology and it is compatible with standard CMOS circuitry. In addition to its affordability, VPD PbSe constitutes a perfect candidate to fill the existing gap in the photonic and uncooled IR imaging detectors sensitive to the MWIR photons. The perspectives opened are numerous and very important, converting the old PbSe detector in a serious alternative to others uncooled technologies in the low cost IR detection market. The number of potential applications is huge, some of them with high commercial impact such as personal IR imagers, enhanced vision systems for automotive applications and other not less important in the security/defence domain such as sensors for active protection systems (APS) or low cost seekers. Despite the fact, unanimously accepted, that uncooled will dominate the majority of the future IR detection applications, today, thermal detectors are the unique plausible alternative. There is plenty of room for photonic uncooled and complementary alternatives are needed. This work allocates polycrystalline PbSe in the current panorama of the uncooled IR detectors, underlining its potentiality in two areas of interest, i.e., very low cost imaging IR detectors and MWIR fast uncooled detectors for security and defence applications. The new method of processing again converts PbSe into an emerging technology.

Ability to work in a computation-limited and computation-variant environment described as “computational awareness” is a desirable feature of a real-time motion estimation system. In this paper, a new multi-path computation-aware algorithm is proposed. One-pass scheme, presented in the prior work by Chen et al., considers only one candidate point which is the median of neighbouring motion vectors (MVs). However, when computational resources are abundant, it is possible to investigate more search paths around points from the prediction set and get a significant improvement both in terms of quality and utilization of available search points (SPs). There are also other enhancements introduced regarding the way of selection of the starting SP and the search strategy, and allocation of resources, which leads to higher PSNR and a better utilization of computational resources.