Home Texture development during cold rolling of unidirectionally solidified Al–Al3Ni alloy
Article
Licensed
Unlicensed Requires Authentication

Texture development during cold rolling of unidirectionally solidified Al–Al3Ni alloy

  • Yasuyuki Kaneno EMAIL logo and Takayuki Takasugi
Published/Copyright: January 3, 2022
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 93 Issue 6

Abstract

Texture development during cold rolling of a unidirectionally solidified Al –Al3Ni alloy was investigated with emphasis on initial orientation, grain structure and the shape of second-phase dispersions. The shape of the Al3Ni second-phase dispersions was variously modified by heat treatment. The starting materials were cold rolled to 90 %reduction in two directions parallel (L-rolling) and perpendicular (T-rolling) to the casting direction. Depending on the initial orientation and grain structure against the rolling direction, different types of rolling textures were developed in the L- and T-rolled materials, respectively. Also, the intensity of the rolling textures in both the L- and T-rolled materials strongly depended on the shape of the Al3Ni dispersions. The observed rolling textures are discussed in association with the deformation zones formed around the Al3Ni dispersions.

Keywords: Unidirectionally solidified Al-Al3Ni alloy; Rolling texture; Second-phase dispersion; Deformation zone; Initial orientation
Y. Kaneno Department of Metallurgy and Materials Science Graduate School of Engineering, Osaka Prefecture University 1-1, Gakuen-cho, Sakai, Osaka 599-8531, Japan Tel.: +81 72 254 9316 Fax.: +81 72 254 9912

  1. This work was supported in part by the Light Metal Educational Foundation, Inc. The authors are grateful to OSAKA FUJI Corporation for supplying materials. They are also grateful to Mr. S. Minami for his assistance in the experiments.

References

1 Lemkey, F.D.; Hertzberg, R.W.; Ford, J.A.: Trans. AIME 233 (1965) 334.Search in Google Scholar

2 Hertzberg, R.W.; Lemkey, F.D.; Ford, J.A.: Trans. AIME 233 (1965) 342.Search in Google Scholar

3 Tada, K.; Ohno, A.: J. Japan Inst. Light Metals 42 (1992) 321.10.2464/jilm.42.321Search in Google Scholar

4 Tada, K.; Ohno, A.: Aluminum 69 (1993) 1092.Search in Google Scholar

5 Kaneno, Y.; Minami, S.; Shimizu, T.; Takasugi, T: J. Japan Inst. Light Metals 50 (2000) 671.10.2464/jilm.50.671Search in Google Scholar

6 Humphreys, F.J.; Hatherly, M: Recrystallization and related annealing phenomena, Pergamon Press, Oxford (1995).Search in Google Scholar

7 Jensen, D.J.; Hansen, N.; Liu, Y.L.: Mater. Sci. Technol. 7 (1991) 369.10.1179/mst.1991.7.4.369Search in Google Scholar

8 Weiland, H.; Rouns, T.N.; Liu, J.: Z. Metallkd. 85 (1994) 592.Search in Google Scholar

9 Kitagawa, K.; Hirata, S.: J. Japan Inst. Light Metals 41 (1991) 766.10.2464/jilm.41.766Search in Google Scholar

10 Hansen, M.: Constitution of Binary Alloys, McGraw-Hill, New York (1985) 118.Search in Google Scholar

11 Dahms, M.; Bunge, H-J: J. Appl. Cryst. 22 (1989) 439.10.1107/S0021889889005261Search in Google Scholar

12 Inoue, H.; Inakazu, N.: J. Japan Inst. Metals 58 (1994) 892.10.2320/jinstmet1952.58.8_892Search in Google Scholar

13 Hirsch, J.; Nes, E.; Lücke, K: Acta metall. 35 (1987) 472.10.1016/0001-6160(87)90249-5Search in Google Scholar

14 Dillamore, L.L.; Roberts, W.T.: Acta metall. 12 (1964) 281.10.1016/0001-6160(64)90204-4Search in Google Scholar

15 Morii, K.; Mecking, H.; Nakayama, Y.: Acta metall. 33 (1985) 379.10.1016/0001-6160(85)90080-XSearch in Google Scholar

16 Driver, J.H.; Jensen, D.J.: Acta metall. mater. 42 (1994) 3105.10.1016/0956-7151(94)90408-1Search in Google Scholar

17 Kaneno, Y.; Kikumoto, H.; Inakazu, N., in: T. Sato, S. Kumai, T. Kobayashi, Y. Murakami (eds.), Proc. Int. Conf. on Aluminum Alloys (ICAA-6), Vol. 2, The Japan Institute of Light Metals, Tokyo (1998) 1281.Search in Google Scholar
Received: 2002-02-01
Published Online: 2022-01-03

© 2002 Carl Hanser Verlag, München

Articles in the same Issue

  1. Frontmatter
  2. Articles/Aufsätze
  3. Mechanical properties of Cu/In – 48 Sn/Cu diffusion-soldered joints
  4. Effect of ultrasonic (cavitation) treatment of the melt on the microstructure evolution during solidification of aluminum alloy ingots
  5. Computer simulation of the long-range diffusional transformation based on the postulated principle of maximum dissipation rate of Gibbs energy
  6. Kinetics of growth of intermetallics in the Cu–Sn system
  7. Atomic composition of the metastable β″ phase precipitate in an Al –Mg–Si alloy
  8. Interfacial tension of metastable immiscible alloys: a novel measurement concept
  9. On the kinetics of the initial oxidation of iron and iron nitride
  10. Synthesis and characterisation of MgAlON
  11. Kinetic studies of oxidation of MgAlON and a comparison of the oxidation behaviour of AlON, MgAlON, O’SiAlON–ZrO2, and BN–ZCM ceramics
  12. Study on warm rolling of AISI 1015 carbon steel
  13. Experimental study on elastic modulus and damping capacity of woodceramics
  14. Texture development during cold rolling of unidirectionally solidified Al–Al3Ni alloy
  15. Wear behavior of A356/M7C3 and A356/SiC particulate metal matrix composites
  16. Microstructural characterization and microhardness of rapidly solidified Al –Ce alloys
  17. Effect of quenching rate on the microstructure of rapidly solidified Al –Sr alloys
  18. The protective mechanism of the native rust layer on Cr-containing steels exposed to marine atmosphere
  19. Notifications/Mitteilungen
  20. Personen
  21. DGM conferences
https://doi.org/10.3139/ijmr-2002-0095
Keywords for this article
Unidirectionally solidified Al-Al3Ni alloy; Rolling texture; Second-phase dispersion; Deformation zone; Initial orientation

Articles in the same Issue

  1. Frontmatter
  2. Articles/Aufsätze
  3. Mechanical properties of Cu/In – 48 Sn/Cu diffusion-soldered joints
  4. Effect of ultrasonic (cavitation) treatment of the melt on the microstructure evolution during solidification of aluminum alloy ingots
  5. Computer simulation of the long-range diffusional transformation based on the postulated principle of maximum dissipation rate of Gibbs energy
  6. Kinetics of growth of intermetallics in the Cu–Sn system
  7. Atomic composition of the metastable β″ phase precipitate in an Al –Mg–Si alloy
  8. Interfacial tension of metastable immiscible alloys: a novel measurement concept
  9. On the kinetics of the initial oxidation of iron and iron nitride
  10. Synthesis and characterisation of MgAlON
  11. Kinetic studies of oxidation of MgAlON and a comparison of the oxidation behaviour of AlON, MgAlON, O’SiAlON–ZrO2, and BN–ZCM ceramics
  12. Study on warm rolling of AISI 1015 carbon steel
  13. Experimental study on elastic modulus and damping capacity of woodceramics
  14. Texture development during cold rolling of unidirectionally solidified Al–Al3Ni alloy
  15. Wear behavior of A356/M7C3 and A356/SiC particulate metal matrix composites
  16. Microstructural characterization and microhardness of rapidly solidified Al –Ce alloys
  17. Effect of quenching rate on the microstructure of rapidly solidified Al –Sr alloys
  18. The protective mechanism of the native rust layer on Cr-containing steels exposed to marine atmosphere
  19. Notifications/Mitteilungen
  20. Personen
  21. DGM conferences
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 17.11.2025 from https://www.degruyterbrill.com/document/doi/10.3139/ijmr-2002-0095/pdf
Scroll to top button