Volume 70, Issue 9-10 -

In this paper, a miniaturized dual-band bandpass filter (DB-BPF) using embedded dual-mode resonator (DMR) with controllable bandwidths is proposed. Two passbands are generated by two sets of resonators operating at two different frequencies. One set of resonators is utilized not only as the resonant elements that yield the lower passband, but also as the feeding structures with source-load coupling to excite the other to produce the upper passband. Sufficient degrees of freedom are achieved to control the center frequencies and bandwidths of two passbands. Moreover, multiple transmission zeros (TZs) are created to improve the passband selectivity of the filter. The design of the filter has been demonstrated by the measurement. The filter features not only miniaturized circuit sizes, low insertion loss, independently controllable central frequencies, but also controllable bandwidths and TZs.

In this paper, a kind of quasi eighth substrate integrated waveguide resonator (QESIWR) with defected fractal structure (DFS) is proposed firstly. Compared with the eighth substrate integrated waveguide resonator (ESIWR), this kind of resonator has lower resonant frequency ( f 0 ), acceptable unloaded quality ( Q u ) value and almost unchanged electric field distribution. In order to validate the properties of QESIWR, a cascaded quadruplet QESIWRs filter is designed and optimized. By using cross coupling and gap coupling compensation, this filter has two transmission zeros (TZs) at each side of the passband. Meanwhile, in comparison with the conventional ones, its size is cut down over 90 %. The measured results agree well with the simulated ones.

In this paper Cylindrical Dielectric Resonator Antenna (CDRA) has been designed for X-band frequency range applications with slot feeding. Bandwidth of designed cylindrical dielectric resonator antenna has been enhanced by making the slot to be resonating and inserting very thin low permittivity dielectric layer between the slot and CDRA. Resonating slot excites the closely spaced HEM 11δ and HEM 21δ mode inside the antenna as well as provides the resonance at the upper side of desired X-band. Low profile low permittivity layer provides the excellent matching of these modes and shift the HEM 21δ mode to higher frequency side at 11.25 GHz with better impedance matching. By combining all of three resonances, nearly 85 % increment in impedance Bandwidth has been obtained with reference to non resonating slot excited CDRA. Fractional impedance bandwidth for proposed design is 48 % and average Gain of 6 dB with more than 92 % radiation efficiency has been shown by the antenna throughout the desired band with broadside pattern.

In this paper, we present a novel frequency reconfigurable antenna which could be easily operate in a single notched-band (WiMAX (3.3–3.6 GHz)) UWB frequency band, another single notched-band (WLAN (5–6 GHz)) UWB frequency band and the dual band-notched UWB frequency band (the stopband covers the WiMAX (3.3–3.6 GHz) and WLAN (5–6 GHz)). The reconfigurability is achieved by changing the states of PIN diodes. The simulated results are in agreement well with the measured results. And the measured patterns are slightly changed with antenna reconfiguration. The proposed antenna is a good candidate for various UWB applications.

The airplane-borne conformal antenna attaches itself tightly with the airplane skin, so the conventional measurement method cannot determine the contribution of the airplane-borne conformal antenna to its radar cross section (RCS). This paper uses the 2D microwave imaging to isolate and extract the distribution of the reflectivity of the airplane-borne conformal antenna. It obtains the 2D spatial spectra of the conformal antenna through the wave spectral transform between the 2D spatial image and the 2D spatial spectrum. After the interpolation from the rectangular coordinate domain to the polar coordinate domain, the spectral domain data for the variation of the scatter of the conformal antenna with frequency and angle is obtained. The experimental results show that the measurement method proposed in this paper greatly enhances the airplane-borne conformal antenna’s RCS measurement accuracy, essentially eliminates the influences caused by the airplane skin and more accurately reveals the airplane-borne conformal antenna’s RCS scatter properties.

Modern radars use complex waveforms to obtain high detection performance and low probabilities of interception and identification. Signals intercepted from multiple radars overlap considerably in both the time and frequency domains and are difficult to separate with primary time parameters. Time–frequency analysis (TFA), as a key signal-processing tool, can provide better insight into the signal than conventional methods. In particular, among the various types of TFA, parameterized time-frequency analysis (PTFA) has shown great potential to investigate the time–frequency features of such non-stationary signals. In this paper, we propose a procedure for PTFA to separate overlapped radar signals; it includes five steps: initiation, parameterized time-frequency analysis, demodulating the signal of interest, adaptive filtering and recovering the signal. The effectiveness of the method was verified with simulated data and an intercepted radar signal received in a microwave laboratory. The results show that the proposed method has good performance and has potential in electronic reconnaissance applications, such as electronic intelligence, electronic warfare support measures, and radar warning.

The research analyses the application of particle filters in estimating and extracting the features of radar signal time-frequency energy distribution. Time-frequency representation is calculated using modified B distribution, where the estimation process model represents one time bin. An adaptive criterion for the calculation of particle weighted coefficients whose main parameters are frequency integral squared error and estimated maximum of mean power spectral density per one time bin is proposed. The analysis of the suggested estimation application has been performed on a generated signal in the absence of any noise, and consequently on modelled and recorded real radar signals. The advantage of the suggested method is in the solution of the issue of interrupted estimations of instantaneous frequencies which appears when these estimations are determined according to maximum energy distribution, as in the case of intersecting frequency components in a multicomponent signal.

Cylindrical resonator principle can be used in GPR asphalt quality measurement calibration. This method relies on ordinary drill core samples that are regularly taken from measured road sections, but now only analyzed for dimensions, density and sometimes chemically. If such a drill sample is covered with proper conductive surfaces, a cylindrical cavity resonator is formed. The baseline of the GPR permittivity recordings can so be found by measuring the resonance behaviour of this covered sample, which can later still be used for those traditional analyses. A clear benefit is the resonator’s 1–2 GHz frequency range which equals that of common commercial GPR systems. Example results and reference readings from known dielectric material are shown. The obtained uncertainty in this case study is 0.02 units of permittivity, when measuring the same sample repeatedly.

Free Space Optical (FSO) communication is being realized as an effective solution for future accessing networks, offering light passed through air. The performance of FSO system can be primarily degraded by various atmospheric attenuations such as rain, fog, haze and snow. At present, hybridization of Dense Wavelength Division Multiplexing (DWDM) with Coarse Wavelength Division Multiplexing (CWDM) becomes necessary to scale the speed and high bandwidth of the services. In this paper, primarily the attenuation values for different weather conditions are calculated. Then the hybrid WDM-FSO system is proposed, designed and the network parameters such as Bit Error Rate (BER), Quality factor (Q factor) and receiver sensitivity are analyzed with respect to link distance for various weather conditions. For investigation, four CWDM (1,510 nm, 1,530 nm, 1,570 nm and 1,570 nm) channel and eight DWDM channels (1,537.4 nm, 1,538.2 nm, 1,539 nm, 1,539.8 nm, 1,540.6 nm, 1,541.4 nm, 1,542.2 nm and 1,543 nm) are considered whose corresponding channel spacing is 20 nm and 0.8 nm, respectively. In addition, the Erbium Doped Fiber Amplifier (EDFA) is inserted at the receiver end in order to enhance the link distance. The proposed hybrid WDM-FSO system is designed to handle the quality of transmission for 12 users, each at a data rate of 2.5 Gbps along an FSO link distance of about 960 km.

In this paper, we develop a B-spline finite-element method (FEM) based on a locally modal wave propagation with anisotropic perfectly matched layers (PMLs), for the first time, to simulate nonlinear and lossy plasmonic waveguides. Conventional approaches like beam propagation method, inherently omit the wave spectrum and do not provide physical insight into nonlinear modes especially in the plasmonic applications, where nonlinear modes are constructed by linear modes with very close propagation constant quantities. Our locally modal B-spline finite element method (LMBS-FEM) does not suffer from the weakness of the conventional approaches. To validate our method, first, propagation of wave for various kinds of linear, nonlinear, lossless and lossy materials of metal-insulator plasmonic structures are simulated using LMBS-FEM in MATLAB and the comparisons are made with FEM-BPM module of COMSOL Multiphysics simulator and B-spline finite-element finite-difference wide angle beam propagation method (BSFEFD-WABPM). The comparisons show that not only our developed numerical approach is computationally more accurate and efficient than conventional approaches but also it provides physical insight into the nonlinear nature of the propagation modes.

Magnetrons have been the most efficient high power microwave sources for decades. In the twenty-first century, many of the development works are headed towards the performance improvement of CW industrial magnetrons. In this review article, the development works and techniques, used on different types of magnetrons, for the performance enhancement in the past two decades have been discussed. The article focuses on the state of the art of CW magnetron and the direction it will take in foreseeable future. In addition it also glimpses some of the major variants of magnetron which have further opened up scope in mm-THz spectrum of electromagnetism.