Article
Licensed
Unlicensed
Requires Authentication
Temperature Measuring in Plastics Processing with Infrared Radiation Thermometers
The Influence of the Absorption Coefficient
-
W. Obendrauf
Published/Copyright:
June 4, 2013
Abstract
In many areas of plastics processing the temperature is a decisive process control parameter. Infrared sensors that detect the heat radiation from molten plastic have a response time in the range of milliseconds. Thus in many processes they offer the only possibility to measure time dependent temperatures with high accuracy.
Received: 1996-5-13
Accepted: 1996-11-27
Published Online: 2013-06-04
Published in Print: 1998-03-01
© 1998, Carl Hanser Verlag, Munich
You are currently not able to access this content.
You are currently not able to access this content.
Articles in the same Issue
- Contents
- Contents
- Editorial
- J. A. Biesenberger, G. Astarita, D. C. Bogue
- Screw Extrusion/Mixing
- Modeling Solids Conveying in Polymer Extruders
- Comparison between LDPE Conventional and Autothermal Extrusion Characteristics
- Transesterification of Ethylene Acetate Copolymer in a Twin Screw Extruder
- Stabilising the Structure of HDPE by the Use of Highly-dispersed Mixture of Fe/FeO
- Pumping Characteristics of an Intermeshing Co-rotating Twin Screw Extruder
- Flow Behaviour of Blends of Poly(ethylene-Co-Acrylic Acid) and Epoxidised Natural Rubber
- Die Extrusion
- Rheological Behaviour of HDPE/PA 11 Blends
- Melt Flow Properties of LDPE/HDPE Blends in Capillary Extrusion
- Fibers and Film
- Rheological Behaviour of LLDPE/LDPE Blends under Elongational Deformation
- Processing/Structure Relationships of Mica-Filled PE-Films with Low Oxygen Permeability
- On the Charge State of Melt-Blown Polymer Materials
- Temperature Measuring in Plastics Processing with Infrared Radiation Thermometers
- Comparative Study of Structure Development in Melt Spinning Polyolefin Fibers
- Moulding
- Sintering Rheology of Semi-Crystalline Polymers
- Molding
- Melt Flow Instabilities of Filled HDPE
- Experimental Validation of Shrinkage Predictions for Injection Molded Products
Articles in the same Issue
- Contents
- Contents
- Editorial
- J. A. Biesenberger, G. Astarita, D. C. Bogue
- Screw Extrusion/Mixing
- Modeling Solids Conveying in Polymer Extruders
- Comparison between LDPE Conventional and Autothermal Extrusion Characteristics
- Transesterification of Ethylene Acetate Copolymer in a Twin Screw Extruder
- Stabilising the Structure of HDPE by the Use of Highly-dispersed Mixture of Fe/FeO
- Pumping Characteristics of an Intermeshing Co-rotating Twin Screw Extruder
- Flow Behaviour of Blends of Poly(ethylene-Co-Acrylic Acid) and Epoxidised Natural Rubber
- Die Extrusion
- Rheological Behaviour of HDPE/PA 11 Blends
- Melt Flow Properties of LDPE/HDPE Blends in Capillary Extrusion
- Fibers and Film
- Rheological Behaviour of LLDPE/LDPE Blends under Elongational Deformation
- Processing/Structure Relationships of Mica-Filled PE-Films with Low Oxygen Permeability
- On the Charge State of Melt-Blown Polymer Materials
- Temperature Measuring in Plastics Processing with Infrared Radiation Thermometers
- Comparative Study of Structure Development in Melt Spinning Polyolefin Fibers
- Moulding
- Sintering Rheology of Semi-Crystalline Polymers
- Molding
- Melt Flow Instabilities of Filled HDPE
- Experimental Validation of Shrinkage Predictions for Injection Molded Products
