Article
Licensed
Unlicensed
Requires Authentication
Simulation of Non-Isothermal Flow in a Modular Buss Kneader and Comparison with Experiment
-
M.-Y. Lyu
Published/Copyright:
June 22, 2013
Abstract
Non-isothermal flow is simulated in a modular Buss Kneader including crosshead screw extruder. A method of calculating cycle averaged mean temperature rises for individual elements is discussed and results are presented. A method is then described for making calculations in a modular multi element Buss Kneader. Finally we compared the calculations with experiment.
Received: 1995-11-20
Accepted: 1996-10-21
Published Online: 2013-06-22
Published in Print: 1997-05-01
© 1997, Carl Hanser Verlag, Munich
You are currently not able to access this content.
You are currently not able to access this content.
Articles in the same Issue
- Contents
- Contents
- Editorial
- Third in a Series: Pioneers of Polymer Processing: Charles Goodyear
- Screw Extrusion/Mixing
- Chaotic Features of Flow in Polymer Processing Equipment-Relevance to Distributive Mixing
- Influence of Design on Mixing Efficiency in a Variable Intermeshing Clearance Mixer
- Simulation of Non-Isothermal Flow in a Modular Buss Kneader and Comparison with Experiment
- Rheological Behaviour of LLDPE/LDPE Blends under Elongational Deformation
- Effect of Compounding Conditions on Mechanical Properties of Glass Fiber-Reinforced Polyamide-6
- Die Extrusion
- A New Approach to Simulation of Die Flow which Incorporates the Extruder and Rotating Screw Tips in the Analysis
- New Aspects Concerning the Design of Coathanger Dies
- Film
- On-Line Birefringence Measurement in Film Blowing of a Linear Low Density Polyethylene
- Brittle Melt Rupture Phenomena in Polymer Processing
- Moulding
- Injection Molding of LDPE/BaSO4 Blends
- An Experimental Study of Rotational Molding of Polypropylene/Polyethylene Copolymers
- Determination of the Inter-Relationships Between Processing Conditions and Properties of an Injection Molded Silicone Ring Using an Experimental Design
- Numerical Simulation of the Flow and Fiber Orientation in Reinforced Thermoplastic Injection Molded Products
- Wide-Angle X-Ray, Densitometric and Microscopical Studies on Injection Molded Polypropylene Disks
Articles in the same Issue
- Contents
- Contents
- Editorial
- Third in a Series: Pioneers of Polymer Processing: Charles Goodyear
- Screw Extrusion/Mixing
- Chaotic Features of Flow in Polymer Processing Equipment-Relevance to Distributive Mixing
- Influence of Design on Mixing Efficiency in a Variable Intermeshing Clearance Mixer
- Simulation of Non-Isothermal Flow in a Modular Buss Kneader and Comparison with Experiment
- Rheological Behaviour of LLDPE/LDPE Blends under Elongational Deformation
- Effect of Compounding Conditions on Mechanical Properties of Glass Fiber-Reinforced Polyamide-6
- Die Extrusion
- A New Approach to Simulation of Die Flow which Incorporates the Extruder and Rotating Screw Tips in the Analysis
- New Aspects Concerning the Design of Coathanger Dies
- Film
- On-Line Birefringence Measurement in Film Blowing of a Linear Low Density Polyethylene
- Brittle Melt Rupture Phenomena in Polymer Processing
- Moulding
- Injection Molding of LDPE/BaSO4 Blends
- An Experimental Study of Rotational Molding of Polypropylene/Polyethylene Copolymers
- Determination of the Inter-Relationships Between Processing Conditions and Properties of an Injection Molded Silicone Ring Using an Experimental Design
- Numerical Simulation of the Flow and Fiber Orientation in Reinforced Thermoplastic Injection Molded Products
- Wide-Angle X-Ray, Densitometric and Microscopical Studies on Injection Molded Polypropylene Disks
