Home In-situ synthesis, microstructure and properties of Ti2AlN/TiB2 composite
Article
Licensed
Unlicensed Requires Authentication

In-situ synthesis, microstructure and properties of Ti2AlN/TiB2 composite

  • Guorui Zhao , Jixin Chen , Liya Zheng , Yueming Li , Hui Zhang , Jianli Gai and Meishuan Li
Published/Copyright: January 31, 2017
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 108 Issue 2

Abstract

Dense Ti2AlN/TiB2 composite was successfully fabricated via in-situ hot pressing using Ti, Al, and BN powders as starting materials. The reaction path, microstructure and typical properties were systematically investigated. It was found that the crystallographic orientation relationship between Ti2AlN and TiB2 could be expressed as: (0 0 0 1) Ti2AlN//(0 0 0 1) TiB2 and [1 2¯ 1 0] Ti2AlN//[1 2¯ 1 0] TiB2 for the first time. The composite exhibits high flexural strength (924 ± 45 MPa), high hardness (13.4 ± 0.3 GPa) and high electrical conductivity (6.5 ± 0.2 × 106 (Ω m)−1).

Keywords: Ti2AlN; Composite; Microstructure; Mechanical properties
*Correspondence address, Dr. Jixin Chen, Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016, China, Tel.: +862483970490, Fax: +862423891320, E-mail:

References

[1] M.W.Barsoum: Prog. Solid State Chem.28 (2000) 201. 10.1016/S0079-6786(00)00006-6Search in Google Scholar

[2] C.F.Hu, H.B.Zhang, F.Z.Li, Q.Huang, Y.W.Bao: Int. J. Refract. Met. Hard Mater.36 (2013) 300. 10.1016/j.ijrmhm.2012.10.011Search in Google Scholar

[3] B.J.Kooi, R.J.Poppen, N.J.M.Carvalho, J. Th. M.De Hosson, M.W.Barsoum: Acta Mater.51 (2003) 2859. 10.1016/S1359-6454(03)00091-0Search in Google Scholar

[4] N.V.Tzenov, M.W.Barsoum: J. Am. Ceram. Soc.83 (2000) 825. 10.1111/j.1151-2916.2000.tb01281.xSearch in Google Scholar

[5] J.Y.Wang, Y.C.Zhou: Annu. Rev. Mater. Res.39 (2009) 415. 10.1146/annurev-matsci-082908-145340Search in Google Scholar

[6] S.B.Li, L.Xiao, G.M.Song, X.M.Wu, W.G.Sloof, S.Zwagg: J. Am. Ceram. Soc.96 (2013) 892. 10.1111/jace.12170Search in Google Scholar

[7] Z.J.Lin, M.J.Zhuo, M.S.Li, J.Y.Wang, Y.C.Zhou: Scr. Mater.56 (2007) 1115. 10.1016/j.scriptamat.2007.01.049Search in Google Scholar

[8] B.Cui, R.Sa, D.D.Jayaseelan, F.Inam, M.J.Reece, W.E.Lee: Acta Mater.60 (2012) 1079. 10.1016/j.actamat.2011.11.010Search in Google Scholar

[9] I.M.Low, W.K.Pang, S.J.Kennedy, R.I.Smith: J. Eur. Ceram. Soc.31 (2011) 159. 10.1016/j.jeurceramsoc.2010.09.014Search in Google Scholar

[10] J.Q.Qin, D.W.He, C.Chen, J.H.Wang, J.Hu, B.W.Yang: J. Alloys Compd.462 (2008) L24. 10.1016/j.jallcom.2007.08.032Search in Google Scholar

[11] P.An, Z.L.He, J.Q.Qin, Z.Y.Li, Y.J.Li, D.W.He: J. Wuhan. Univ. Technol.26 (2011) 914. 10.1007/s11595-011-0336-8Search in Google Scholar

[12] W.K.Pang, I.M.Low, S.J.Kennedy, R.I.Smith: Mater. Sci. Eng. A528 (2010) 137. 10.1016/j.msea.2010.08.012Search in Google Scholar

[13] W.K.Pang, I.M.Low, Z.M.Sun: J. Am. Ceram. Soc.93 (2010) 2871. 10.1111/j.1551-2916.2010.03764.xSearch in Google Scholar

[14] J.Emmerlich, D.Music, P.Eklund, O.Wilhelmsson, U.Jansson, J.M.Schneider, H.Hogberg, L.Hultman: Acta Mater.55 (2007) 1479. 10.1016/j.actamat.2006.10.010Search in Google Scholar

[15] M.Bugnet, T.Cabioc'h, V.Mauchamp, P.Guérin, M.Marteau, M.Jaouen: J. Mater. Sci.45 (2010) 5547. 10.1007/s10853-010-4615-0Search in Google Scholar

[16] D.J.Tallman, E.N.Hoffman, N.C.El'ad, B.L.Garcia-Diaz, G.Kohse, R.L.Sindelar, M.W.Barsoum: Acta Mater.85 (2015) 132. 10.1016/j.actamat.2014.10.068Search in Google Scholar

[17] J.X.Chen, Y.C.Zhou: Scr. Mater.50 (2004) 897. 10.1016/j.scriptamat.2003.12.002Search in Google Scholar

[18] J.F.Zhang, L.J.Wang, L.Shi, W.Jiang, L.D.Chen: Scr. Mater.56 (2007) 241. 10.1016/j.scriptamat.2006.09.029Search in Google Scholar

[19] X.Zhan, Z.Li, Z.H.Gao, L.Y.Zheng, X.H.Wang, J.Y.Wang, Y.C.Zhou: J. Am. Ceram. Soc.95 (2012) 2314. 10.1111/j.1551-2916.2012.05252.xSearch in Google Scholar

[20] C.Li, M.S.Li, Y.C.Zhou, J.Zhang, L.F.He: J. Am. Ceram. Soc.90 (2007) 3615. 10.1111/j.1551-2916.2007.01954.xSearch in Google Scholar

[21] L.Y.Zheng, J.Y.Wang, J.X.Chen, M.Y.Liu, Y.J.Sun, Y.C.Zhou: J. Am. Ceram. Soc.96 (2013) 365. 10.1111/jace.12140Search in Google Scholar

[22] Y.C.Zhou, D.T.Wan, Y.W.Bao, J.Y.Wang: J. Am. Ceram. Soc.3 (2006) 47. 10.1111/j.1744-7402.2006.02057.xSearch in Google Scholar

[23] J.F.Zhang, L.J.Wang, W.Jiang, L.D.Chen: Mater. Sci. Eng. A487 (2008) 137. 10.1016/j.msea.2007.12.004Search in Google Scholar

[24] R.G.Munro: J. Res. Nat. Inst. Stand. Technol.105 (2000) 709. 10.6028/jres.105.057Search in Google Scholar

[25] S.Tuffe, J.Dubois, G.Fantozzi, G.Barbier: Int. J. Refract. Met. Hard Mater.14 (1996) 305. 10.1016/S0263-4368(96)00012-1Search in Google Scholar

[26] N.S.Karthiselva, B.S.Murty, S.R.Bakshi: Int. J. Refract. Met. Hard Mater.48 (2015) 201. 10.1016/j.ijrmhm.2014.09.015Search in Google Scholar

[27] B.Basu, G.B.Raju, A.K.Suri: Int. Mater. Rev.51 (2006) 352. 10.1179/174328006X102529Search in Google Scholar

[28] W.B.Zhou, B.C.Mei, J.Q.Zhu: J. Ceram. Process. Res.10 (2009) 102.Search in Google Scholar

[29] J.X.Chen, G.R.Zhao, Y.C.Zhou, Ti2AlN/TiB2 composite and preparation method thereof, China Patent: ZL 201310027547.6.Search in Google Scholar

[30] M.W.Barsoum, L.Farber, T.El-Raghy: Metal. Mater. Trans. A30 (1999) 1727. 10.1007/s11661-999-0172-zSearch in Google Scholar

[31] M.W.Barsoum, A.Murugaiah, S.R.Kalidindi, T.Zhen: Phys. Rev. Lett.92 (2004) 255508. 10.1103/PhysRevLett.92.255508Search in Google Scholar PubMed

[32] M.W.Barsoum, T.Zhen, S.R.Kalidindi, M.Radovic: Nat. Mater.2 (2003) 107. 10.1038/nmat814Search in Google Scholar PubMed

[33] F.C.Frank, A.N.Stroh: Proc. Phys. Soc. B65 (1952) 811. 10.1088/0370-1301/65/10/311Search in Google Scholar

[34] M.W.Barsoum, M.Ali, T.El-Raghy: Metall. Mater. Trans. A31 (2000) 1857–1865. 10.1007/s11661-006-0243-3Search in Google Scholar

Received: 2016-08-19
Accepted: 2016-10-31
Published Online: 2017-01-31
Published in Print: 2017-02-10

© 2017, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Editorial
  4. A new editor for IJMR
  5. Original Contributions
  6. Structural anisotropy in equal-channel angular extruded nickel revealed by dilatometric study of excess volume
  7. Low-temperature transformation to bainite in a medium-carbon steel
  8. Study on the welding continuous cooling transformation and weldability of SA508Gr4 steel for nuclear pressure vessels
  9. Phase precipitation in transition metal-containing 354-type alloys
  10. Effect of laser alloying on heat-treated light alloys
  11. In-situ synthesis, microstructure and properties of Ti2AlN/TiB2 composite
  12. Characterization of mechanical properties of Al/TiCP MMC
  13. Performance evaluation of polysulfone/graphene nanocomposites
  14. Short Communications
  15. Influence of Cu and Mg addition on age-related deterioration in strength and creep behavior of Zn-12Al die casting alloys
  16. Effects of mixing speed of a composite on its friction coefficient and wear resistance
  17. DGM News
  18. DGM News
https://doi.org/10.3139/146.111460
Keywords for this article
Ti2AlN; Composite; Microstructure; Mechanical properties

Articles in the same Issue

  1. Contents
  2. Contents
  3. Editorial
  4. A new editor for IJMR
  5. Original Contributions
  6. Structural anisotropy in equal-channel angular extruded nickel revealed by dilatometric study of excess volume
  7. Low-temperature transformation to bainite in a medium-carbon steel
  8. Study on the welding continuous cooling transformation and weldability of SA508Gr4 steel for nuclear pressure vessels
  9. Phase precipitation in transition metal-containing 354-type alloys
  10. Effect of laser alloying on heat-treated light alloys
  11. In-situ synthesis, microstructure and properties of Ti2AlN/TiB2 composite
  12. Characterization of mechanical properties of Al/TiCP MMC
  13. Performance evaluation of polysulfone/graphene nanocomposites
  14. Short Communications
  15. Influence of Cu and Mg addition on age-related deterioration in strength and creep behavior of Zn-12Al die casting alloys
  16. Effects of mixing speed of a composite on its friction coefficient and wear resistance
  17. DGM News
  18. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 16.11.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.111460/pdf
Scroll to top button