Article
Licensed
Unlicensed Requires Authentication

DGM News

Published/Copyright: January 11, 2014
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 105 Issue 1

Published Online: 2014-01-11
Published in Print: 2014-01-09

© 2014, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Microwave absorbing materials based on polyaniline composites: a review
  5. Atomic mobilities in fcc Cu–Mn–Ni–Zn alloys and their characterizations of uphill diffusion and zero-flux plane phenomena
  6. Synthesis and characterization of nanocristalline Fe-40 at.% Si alloy prepared by high energy ball milling
  7. An investigation of the microstructure and hydrogenation/dehydrogenation properties of ball-milled CeMg12 alloys with Ni powders
  8. Nanoscratch characterization of indium nitride films
  9. Role of axial thrust in the formation of microstructure and fracture surface of the weld zone in friction stir welded AA6063 aluminium alloy
  10. Microstructures and corrosion resistance of three typical superlight Mg–Li alloys
  11. The effect of magnetron-deposited Al2O3 coating on the corrosion resistance of Ti–Al alloys in a 9 %O2 + 0.2 %HCl + 0.08 %SO2 + N2 atmosphere
  12. Homogenization of direct chill cast AlSi1MgMn billets
  13. Effect of rare earth Y addition on two-phase Ni53Mn22Co6Ga19 high-temperature shape memory alloy
  14. Thermal treatment induced transition from Zn3(OH)2(BDC)2 (MOF-69c) to Zn4O(BDC)3 (MOF-5)
  15. Thermal investigation of alumina-based pastes and refractory mixturesd
  16. Short Communications
  17. One-step magnetic modification of non-magnetic solid materials
  18. DGM News
  19. DGM News
https://doi.org/10.3139/146.014014

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Microwave absorbing materials based on polyaniline composites: a review
  5. Atomic mobilities in fcc Cu–Mn–Ni–Zn alloys and their characterizations of uphill diffusion and zero-flux plane phenomena
  6. Synthesis and characterization of nanocristalline Fe-40 at.% Si alloy prepared by high energy ball milling
  7. An investigation of the microstructure and hydrogenation/dehydrogenation properties of ball-milled CeMg12 alloys with Ni powders
  8. Nanoscratch characterization of indium nitride films
  9. Role of axial thrust in the formation of microstructure and fracture surface of the weld zone in friction stir welded AA6063 aluminium alloy
  10. Microstructures and corrosion resistance of three typical superlight Mg–Li alloys
  11. The effect of magnetron-deposited Al2O3 coating on the corrosion resistance of Ti–Al alloys in a 9 %O2 + 0.2 %HCl + 0.08 %SO2 + N2 atmosphere
  12. Homogenization of direct chill cast AlSi1MgMn billets
  13. Effect of rare earth Y addition on two-phase Ni53Mn22Co6Ga19 high-temperature shape memory alloy
  14. Thermal treatment induced transition from Zn3(OH)2(BDC)2 (MOF-69c) to Zn4O(BDC)3 (MOF-5)
  15. Thermal investigation of alumina-based pastes and refractory mixturesd
  16. Short Communications
  17. One-step magnetic modification of non-magnetic solid materials
  18. DGM News
  19. DGM News
Downloaded on 14.4.2026 from https://www.degruyterbrill.com/document/doi/10.3139/146.014014/html
Scroll to top button