Morphology, mechanical, bound rubber, swelling, and dynamic mechanical studies of chlorobutyl elastomer nanocomposites: effect of multiwalled carbon nanotube and solvent
Abstract
Multiwalled carbon nanotube (MWCNT) reinforced chlorobutyl elastomer nanocomposites were prepared. The morphology of nanocomposite samples has been studied from scanning electron microscopy (SEM). The effect of MWCNT loadings on mechanical properties shows increase in tensile strength, hardness, and modulus and decrease in elongation at break with MWCNT loadings, which can be attributed toward better chlorobutyl-MWCNT interaction. At higher filler loading, the rate of increase slowly decreases. The above explanation was also verified from bound rubber (BdR) measurements, showing increase in BdR contents with MWCNT loading. Swelling of the nanocomposites in chloroform, benzene, and trichloroethylene was measured and found to be dependent on both MWCNT concentration and the type of solvent used. The degree of swelling, diffusion coefficient, and penetration rate was calculated. The effect of solvent on swelling properties at different periods of time shows that the degree of swelling increases with time and decreases with concentration of MWCNT loading. Dynamic mechanical properties of nanocomposites have been studied as a function of temperature (from -100°C to 100°C) at a constant frequency of 1 Hz and 1% strain. The effect of MWCNT loading on storage modulus, loss modulus, and loss tangent has been studied. The nonlinearity in tan δ and storage modulus and loss modulus was explained on the basis of MWCNT-elastomer interaction. The smooth Cole-Cole plots explain the nonlinearity in the nanocomposites as well as good distribution of MWCNT in the elastomer matrix.
References
[1] Gojny FH, Wichmann MHG, Fiedler B, Kinloch IA, Bauhofer W, Windle AH, et al. Polymer 2006, 47, 2036–2045.10.1016/j.polymer.2006.01.029Search in Google Scholar
[2] Zheng W, Wong SC, Sue HJ. Polymer 2002, 73, 6767.10.1016/S0032-3861(02)00599-2Search in Google Scholar
[3] Lu W, Lin H, Wu D, Chen G. Polymer 2006, 47, 4440–4444.10.1016/j.polymer.2006.03.107Search in Google Scholar
[4] El-Tantawy F, Kamada K, Ohnabe H. Mater. Lett. 2002, 56, 112–126.Search in Google Scholar
[5] Chung DD. J Mater. Sci. 2004, 39, 2645–2661.Search in Google Scholar
[6] Sandler JKW, Kirk JE, Kinloch IA, Shaffer MSP, Windle AH. Polymer 2003, 44, 5893–5899.10.1016/S0032-3861(03)00539-1Search in Google Scholar
[7] Zhang Q, Rastogi S, Chen D, Lippits D, Lemstra PJ. Carbon 2006, 44, 778–785.10.1016/j.carbon.2005.09.039Search in Google Scholar
[8] Maa P-C, Siddiqui NA, Maromb G, Kim J-K. Composites Part A 2010, 41, 1345–1367.10.1016/j.compositesa.2010.07.003Search in Google Scholar
[9] Dutta NK, Tripathy DK. Colloid Polym. Sci. 1991, 269, 331–342.Search in Google Scholar
[10] Shanmugharaj AM, Bae JH, Lee Noh KY, Lee WH, Ryu SH, Comp SH. Sci. Technol. 2007, 67, 1813–1822.Search in Google Scholar
[11] Dutta NK, Tripathi DK. J. Appl. Polym. Sci. 1992, 44, 1635–1648.Search in Google Scholar
[12] Fakhrul-Razi A, Atieh MA, Girun N, Chuah TG, El-Sadiq M, Biak DRA. Comput. Struct. 2006, 75, 496–500.Search in Google Scholar
[13] Bokobza L, Diop AL, Fournier V, Minne JP, Bruneel JL. Macro. Symp. 2005, 87, 230.Search in Google Scholar
[14] Park IS, Kim KJ, Nam D, Lee J, Yim W. Polym. Eng. Sci. 2007, 47, 1396–1405.Search in Google Scholar
[15] Pham TT, Sridhar V, Kim JK. Polym. Compos. 2009, 30, 121–130.Search in Google Scholar
[16] Nanda M, Tripathy DK. eXPRESS Polym. Lett. 2008, 2, 855–865.Search in Google Scholar
[17] Roychoudhury A, De SK, De PP, Ayala JA, Joyce GA. Rubber Chem. Technol. 1994, 67, 662–671.Search in Google Scholar
[18] Kwon SC, Adachi T, Araki W, Yamaji A. Acta Mater. 2006, 54, 3369–3374.Search in Google Scholar
[19] Barr-Howell BD, Peppas NA. J. Appl. Polym. Sci. 1985, 30, 4583–4589.Search in Google Scholar
[20] Passiniemi P. Polymer 1995, 36, 341–344.10.1016/0032-3861(95)91322-XSearch in Google Scholar
[21] Khinnavar RS, Aminabhavi TM. J. Appl. Polym. Sci. 1992, 46, 909–920.Search in Google Scholar
[22] Wolf CJ, Barnmann JA, Grayson MA. J. Appl. Polym. Sci. Part B Polym. Phys. 1991, 29, 1533–1539.Search in Google Scholar
[23] Wolff S, Wang M-J. Carbon black reinforcement of elastomers. In Carbon Black: Science and Technology, Donnet, JB, Bansal, RC, Wang, MJ, Eds., Marcel Dekker: New York, USA, 1993, pp. 289–345.Search in Google Scholar
[24] Roychoudhury A, De PP. J. Appl. Polym. Sci. 1995, 55, 9–15.Search in Google Scholar
[25] Fua S-Y, Feng X-Q, Lauke B, Mai Y-W. Composites Part B 2008, 39, 933–961.10.1016/j.compositesb.2008.01.002Search in Google Scholar
[26] Wolff S, Wang MJ, Tan EH. Rubber Chem. Technol. 1993, 66, 163–177.Search in Google Scholar
[27] Bal S, Samal SS. Bull. Mater. Sci. 2007, 30, 379–386.Search in Google Scholar
[28] Sahoo BP, Naskar K, Tripathy DK. J. Mater. Sci. 2012, 47, 2421–2433.Search in Google Scholar
[29] Sridhar V, Gupta BR, Tripathy DK. J. Appl. Polym. Sci. 2006, 102, 715–720.Search in Google Scholar
[30] Chakraborty SK, Bhowmick AK, De SK. Polym. Rev. 1981, 21, 313–332.Search in Google Scholar
[31] Erman B, Mark JE. Macromolecules 1992, 25, 1919.10.1021/ma00033a013Search in Google Scholar
[32] Abdel-Ghani SA, Madkour TM, Osman HM, Mohamed AR. Egypt. J. Sol. 2000, 23, 307.Search in Google Scholar
[33] Bokobza L. Polymer 2007, 48, 4907–4920.10.1016/j.polymer.2007.06.046Search in Google Scholar
[34] Angell CA, Ngai KL, McKenna GB, McMillan PF, Martin SW. J. Appl. Phys. 2000, 88, 3113.Search in Google Scholar
[35] Valentini L, Amentano I, Biagotti J, Kenny JM, Santucci S. Diamond Relat. Mater. 2003, 12, 1601.Search in Google Scholar
[36] McLachlan DS, Chiteme C, Park C, Wise KE, Lowther SE, Lillehei PT, Siochi EJ, Harrison JS. J. Polym. Sci. Part B Polym. Phys. 2005, 43, 3273–3287.Search in Google Scholar
©2014 by Walter de Gruyter Berlin Boston
Articles in the same Issue
- Masthead
- Masthead
- Publisher’s note
- Editorial changes at the Journal of Polymer Engineering
- Editorial
- A new Editor-in-Chief for Journal of Polymer Engineering
- Original articles
- Microcellular injection molding of recycled poly(ethylene terephthalate) blends with chain extenders and nanoclay
- Structure and performance of polybutene-1 pipes produced via mandrel rotation extrusion
- Analysis of the effect of molecular weight and testing rate on shear strength of epoxidized natural rubber-based adhesives with a statistical model
- The use of waste rubber in natural rubber in the presence of maleic anhydride-grafted natural rubber (MA-g-NR): study on curing, rheology, morphology, and properties of the blend
- Morphology, mechanical, bound rubber, swelling, and dynamic mechanical studies of chlorobutyl elastomer nanocomposites: effect of multiwalled carbon nanotube and solvent
- Nonisothermal crystallization kinetics of polybutene-1 containing nucleating agent with acid amides structure
- The effect of organoclay contents on morphological characterization, mechanical and thermal properties of epoxidized natural rubber-50 toughened polyamide 6 nanocomposites
- Tensile properties of polycaprolactone/nano-CaCO3 composites
- Influence of two novel compatibilizers on the properties of LDPE/organoclay nanocomposites
- Development and characterization of novel photopolymerizable formulations for stereolithography
- Modeling of vapor-liquid equilibrium for binary polypropylene glycol/solvent solutions using cubic equation of state models: optimization and comparison of CEoS models
Articles in the same Issue
- Masthead
- Masthead
- Publisher’s note
- Editorial changes at the Journal of Polymer Engineering
- Editorial
- A new Editor-in-Chief for Journal of Polymer Engineering
- Original articles
- Microcellular injection molding of recycled poly(ethylene terephthalate) blends with chain extenders and nanoclay
- Structure and performance of polybutene-1 pipes produced via mandrel rotation extrusion
- Analysis of the effect of molecular weight and testing rate on shear strength of epoxidized natural rubber-based adhesives with a statistical model
- The use of waste rubber in natural rubber in the presence of maleic anhydride-grafted natural rubber (MA-g-NR): study on curing, rheology, morphology, and properties of the blend
- Morphology, mechanical, bound rubber, swelling, and dynamic mechanical studies of chlorobutyl elastomer nanocomposites: effect of multiwalled carbon nanotube and solvent
- Nonisothermal crystallization kinetics of polybutene-1 containing nucleating agent with acid amides structure
- The effect of organoclay contents on morphological characterization, mechanical and thermal properties of epoxidized natural rubber-50 toughened polyamide 6 nanocomposites
- Tensile properties of polycaprolactone/nano-CaCO3 composites
- Influence of two novel compatibilizers on the properties of LDPE/organoclay nanocomposites
- Development and characterization of novel photopolymerizable formulations for stereolithography
- Modeling of vapor-liquid equilibrium for binary polypropylene glycol/solvent solutions using cubic equation of state models: optimization and comparison of CEoS models