Abstract
The aim of this review is to present a summary of the published papers of the heat transfer and pressure drop characteristics for single-phase flow in helically coiled tubes. The effect of geometrical parameters such as curvature ratio, coil pitch and working conditions such as Reynolds number, Dean number, flow rate and flow arrangement on heat transfer and pressure drop in helically coiled tubes are determined in the light of the experimental, numerical and analytical studies in the literature. Also, the effect of using nanofluids in comparison with conventional fluids, using enhanced surfaces such as corrugated, micro-finned, dimpled with regards to smooth surfaces and wire coil insert usage in helically coiled tubes are discussed. The correlations proposed for determination of Nusselt number and friction factor in helically coiled tubes are presented in detail separately under laminar and turbulent flow regimes. The studies show that usage of helically coiled tube merely gives higher heat transfer rate and pressure drop in comparison to straight one, additionally, the heat transfer performance increases with the inclusion of the combination of other passive heat transfer enhancement methods to helically coiled tube. Moreover, the subject of single-phase flow in helically coiled tubes is ascertained to be worth researching due to the fact that there are limited number of studies and is still no empirical or analytical model/correlation in the case of using enhanced surfaces and wire coil insert. Forthcoming researches on this issue in the near future will be considered as pioneer ones in literature.
Funding source: Yildiz Technical University
Award Identifier / Grant number: FOA-2019-3582
Funding source: National Science and Technology Development Agency
-
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: The authors would like to acknowledge that this paper is submitted in partial fulfillment of the requirements for PhD degree at Yildiz Technical University. This work was supported by Research Fund of the Yildiz Technical University. Project Number: FOA-2019-3582. The sixth author acknowledges the support provided by National Science and Technology Development Agency (NSTDA) under the Research Chair Grant, and the Thailand Science Research and Innovation (TSRI) under the Fundamental Fund 2022.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
References
Akbaridoust, F., Rakhsha, M., Abbasi, A., and Saffar-Avval, M. (2013). Experimental and numerical investigation of nanofluid heat transfer in helically coiled tubes at constant wall temperature using dispersion model. Int. J. Heat Mass Tran. 58: 480–491, https://doi.org/10.1016/j.ijheatmasstransfer.2012.11.064.Search in Google Scholar
Akhavan-Behabadi, M.A., Pakdaman, M.F., and Ghazvini, M. (2012). Experimental investigation on the convective heat transfer of nanofluid flow inside vertical helically coiled tubes under uniform wall temperature condition. Int. Commun. Heat Mass Tran. 39: 556–564, https://doi.org/10.1016/j.icheatmasstransfer.2012.02.008.Search in Google Scholar
Al-Jabair, S.J.H. and Al-taee, A.H.A. (2013). Experimental study of Hs of shell and helically coiled tube heat exchangers. Eng. Technol. J. 31: 172–196.10.30684/etj.2013.71256Search in Google Scholar
Ali, S. (2001). Pressure drop correlations for flow through regular helical coil tubes. Fluid Dynam. Res. 28: 295–310, https://doi.org/10.1016/S0169-5983(00)00034-4.Search in Google Scholar
Alimoradi, A. and Maghareh, M. (2017). Numerical investigation of heat transfer intensification in shell and helically coiled finned tube heat exchangers and design optimization. Chem. Eng. Process 121: 125–143, https://doi.org/10.1016/j.cep.2017.08.005.Search in Google Scholar
Alimoradi, A. and Veysi, F. (2017). Optimal and critical values of geometrical parameters of shell and helically coiled tube heat exchangers. Case Stud. Therm. Eng. 10: 73–78, https://doi.org/10.1016/j.csite.2017.03.003.Search in Google Scholar
Allahyar, H.R., Hormozi, F., and Zare Nezhad, B. (2016). Experimental investigation on the thermal performance of a coiled heat exchanger using a new hybrid nanofluid. Exp. Therm. Fluid Sci. 76: 324–329, https://doi.org/10.1016/j.expthermflusci.2016.03.027.Search in Google Scholar
Andhare, A., Kriplani, V.M., and Modak, J.P. (2014). Thermal analysis of a helical coil heat exchanger. Int. J. Innovat. Res. Adv. Eng. 1: 135–143.Search in Google Scholar
Andrzejczyk, R. and Muszyński, T. (2016). Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness. Arch. Therm. 37: 137–159, https://doi.org/10.1515/aoter-2016-0032.Search in Google Scholar
Ardekani, A.M., Kalantar, V., and Heyhat, M.M. (2019). Experimental study on heat transfer enhancement of nanofluid flow through helical tubes. Adv. Powder Technol. 30: 1815–1822, https://doi.org/10.1016/j.apt.2019.05.026.Search in Google Scholar
Austen, D.S. and Soliman, H.M. (1988). Laminar flow and heat transfer in helically coiled tubes with substantial pitch. Exp. Therm. Fluid Sci. 1: 183–194, https://doi.org/10.1016/0894-1777(88)90035-0.Search in Google Scholar
Babita, S., Sharma, S.K., and Gupta, S.M. (2019). Experimental studies on pressuredrop/friction factor of CNT nanofluids flowing through helical coils and development of a new empirical correlation. J. Dispersion Sci. Technol. 41: 1–11, https://doi.org/10.1080/01932691.2019.1610420.Search in Google Scholar
Bahrehmand, S. and Abbassi, A. (2016). Heat transfer and performance analysis of nanofluid flow in helically coiled tube heat exchangers. Chem. Eng. Res. Des. 109: 628–637, https://doi.org/10.1016/j.cherd.2016.03.022.Search in Google Scholar
Beigzadeh, R. and Rahimi, M. (2012). Prediction of thermal and fluid flow characteristics in helically coiled tubes using ANFIS and GA based correlations. Int. Commun. Heat Mass Tran. 39: 1647–1653, https://doi.org/10.1016/j.icheatmasstransfer.2012.10.011.Search in Google Scholar
Bergles, A.E. (1998). Techniques to enhance heat transfer. In: Rohsenow, W.M., Hartnett, J.P., and Cho, Y.I. (Eds.), Handbook of heat transfer. New York: McGraw-Hill.Search in Google Scholar
Bertelsen, A.F. (1975). An experimental investigation of low Reynolds number secondary streaming effects associated with an oscillating viscous flow in a curved pipe. J. Fluid Mech. 70: 519–527, https://doi.org/10.1017/S0022112075002169.Search in Google Scholar
Bhanvase, B.H., Sayankar, S.D., Kapre, A., Fule, P.J., and Sonawane, S.H. (2018). Experimental investigation on intensified convective heat transfer coefficient of water based PANI nanofluid in vertical helical coiled heat exchanger. Appl. Therm. Eng. 128: 134–140, https://doi.org/10.1016/j.applthermaleng.2017.09.009.Search in Google Scholar
Bozzoli, F., Cattani, L., and Rainieri, S. (2016). Effect of wall corrugation on local convective heat transfer in coiled tubes. Int. J. Heat Mass Tran. 101: 76–90, https://doi.org/10.1016/j.ijheatmasstransfer.2016.04.106.Search in Google Scholar
Cancan, Z., Dingbiao, W., Sa, X., Yong, H., and Xu, P. (2017). Numerical investigation of heat transfer and pressure drop in helically coiled tube with spherical corrugation. Int. J. Heat Mass Tran. 113: 332–341, https://doi.org/10.1016/j.ijheatmasstransfer.2017.05.108.Search in Google Scholar
Chavda, N.K., Jani, J.P., Patel, A.K., Zala, K.P., and Nimbark, N.G. (2014). Effect of nanofluid on friction factor of pipe and pipe fittings: part I – effect of aluminum oxide nanofluid. Int. J. Curr. Eng. Technol. 4: 4069–4074.Search in Google Scholar
Chen, H., Moria, H., Ahmed, S.Y., Nisar, K.S., Mohamed, A.M., Heidarshenas, B., Arsalansoo, A., and Youshanlouei, M.M. (2021). Thermal/exergy and economic efficiency analysis of circumferentially corrugated helical tube with constant wall temperature. Case Stud. Therm. Eng. 23: 1–17, https://doi.org/10.1016/j.csite.2020.100803.Search in Google Scholar
Cioncolini, A. and Santini, L. (2006). On the laminar to turbulent flow transition in diabatic. Exp. Therm. Fluid Sci. 30: 653–661, https://doi.org/10.1016/j.expthermflusci.2006.01.004.Search in Google Scholar
Coronel, P. and Sandeep, K.P. (2008). Heat transfer coefficient in helical heat exchangers under turbulent flow conditions. Int. J. Food Eng. 4: 1–12, https://doi.org/10.2202/1556-3758.1209.Search in Google Scholar
Darzi, A.A.R., Abuzadeh, M., and Omidi, M. (2021). Numerical investigation on thermal performance of coiled tube with helical corrugated wall. Int. J. Therm. Sci. 161: 1–11, https://doi.org/10.1016/j.ijthermalsci.2020.106759.Search in Google Scholar
Dean, W.R. (1927). XVI. Note on the motion of fluid in a curved pipe. Philos. Mag. Ser. 7. 4: 208–223, https://doi.org/10.1080/14786440708564324.Search in Google Scholar
Dean, W.R. (1928). LXXII. The stream-line motion of fluid in a curved pipe. Philos. Mag. Ser. 7. 5: 673–695, https://doi.org/10.1080/14786440408564513.Search in Google Scholar
Dewan, A., Mahanta, P., Raju, K.S., and Kumar, P.S. (2004). Review of passive heat transfer augmentation techniques. Proc. IME J. Power Energy 218: 509–527, https://doi.org/10.1243/0957650042456953.Search in Google Scholar
Dravid, A.N., Smith, K.A., Merrill, E.W., and Brian, P.L.T. (1971). Effect of secondary fluid motion on laminar flow heat transfer in helically coiled tubes. Am. Inst. Chem. Eng. J. 17: 1114–1122, https://doi.org/10.1002/aic.690170517.Search in Google Scholar
El-Genk, M.S. and Schriener, T.M. (2017). A review and correlations for convection heat transfer and pressure losses in toroidal and helically coiled tubes. Heat transfer Eng. 38: 447–474, https://doi.org/10.1080/01457632.2016.1194693.Search in Google Scholar
Etghani, M.M. and Baboli, S.A.H. (2017). Numerical investigation and optimization of heat transfer and exergy loss in shell and helical tube heat exchanger. Appl. Therm. Eng. 121: 294–301, https://doi.org/10.1016/j.applthermaleng.2017.04.074.Search in Google Scholar
Eustice, J. (1910). Flow of water in curved pipes. Proc. Roy. Soc. Lond. Ser. A 84: 107–118, https://doi.org/10.1098/rspa.1910.0061.Search in Google Scholar
Fakoor-Pakdaman, M., Akhavan-Behabadi, M.A., and Razi, P. (2013). An empirical study on the pressure drop characteristics of nanofluid flow inside helically coiled tubes. Int. J. Therm. Sci. 65: 206–213, https://doi.org/10.1016/j.ijthermalsci.2012.10.014.Search in Google Scholar
Gholamalizadeh, E., Hosseini, E., Jamnani, M.B., Amiri, A., Dehghan saee, A., and Alimoradi, A. (2019). Study of intensification of the heat transfer in helically coiled tube heat exchangers via coiled wire inserts. Int. J. Therm. Sci. 141: 72–83, https://doi.org/10.1016/j.ijthermalsci.2019.03.029.Search in Google Scholar
Gore, G.G. and Yarasu, R.B. (2015). Convective heat transfer analysis from helically coiled tube using CFD and experimental methodology. Int. J. Sci. Res. Dev. 3: 475–478.Search in Google Scholar
Gou, J., Ma, H., Yang, Z., and Shan, J. (2017). An assessment of heat transfer models of water flow in helically coiled tubes based on selected experimental datasets. Ann. Nucl. Energy 110: 648–667, https://doi.org/10.1016/j.anucene.2017.07.015.Search in Google Scholar
Grindley, J.H. and Gibson, A.H. (1908). The frictional resistance to the flow of air through a pipe. Proc. Roy. Soc. Lond. Ser. A 80: 114–139, https://doi.org/10.1098/rspa.1908.0006.Search in Google Scholar
Guo, L., Feng, Z., and Chen, X. (2001). An experimental investigation of the frictional ΔP of steam-water two-phase flow in helical coils. Int. J. Heat Mass Tran. 44: 2601–2610, https://doi.org/10.1016/S0017-9310(00)00312-4.Search in Google Scholar
Gupta, R., Wanchoo, R.K., and Ali, T.R.M.J. (2011). Laminar flow in helical coils: a parametric study. Ind. Eng. Chem. Res. 50: 1150–1157, https://doi.org/10.1021/ie101752z.Search in Google Scholar
Hashemi, S.M. and Akhavan-Behabadi, M.A. (2012). An empirical study on heat transfer and pressure drop characteristics of CuO–base oil nanofluid flow in a horizontal helically coiled tube under constant heat flux. Int. Commun. Heat Mass Tran. 39: 144–151, https://doi.org/10.1016/j.icheatmasstransfer.2011.09.002.Search in Google Scholar
Hardik, B.K., Baburajan, P.K., and Prabhu, S.V. (2015). Local h in helical coils with single phase flow. Int. J. Heat Mass Tran. 89: 522–538, https://doi.org/10.1016/j.ijheatmasstransfer.2015.05.069.Search in Google Scholar
Heydari, O., Miansari, M., Arasteh, H., and Toghraie, D. (2020). Optimizing the hydrothermal performance of helically corrugated coiled tube heat exchangers using Taguchi’s empirical method: energy and exergy analysis. J. Therm. Anal. Calorim. 145: 2741–2752, https://doi.org/10.1007/s10973-020-09808-3.Search in Google Scholar
Hozien, O., El-Maghlany, W.M., Sorour, M.M., and Mohamed, Y.S. (2021). Experimental study on heat transfer and pressure drop characteristics utilizing three types of water based nanofluids in a helical coil under isothermal boundary condition. J. Taiwan Inst. Chem. Eng. 1–16, https://doi.org/10.1016/j.jtice.2021.08.028.Search in Google Scholar
Ito, H. (1959). Friction factors for turbulent flow in curved pipes. J. Basic Eng. 81: 123–132, https://doi.org/10.1115/1.4008390.Search in Google Scholar
Jamshidi, N., Farhadi, M., Ganji, D.D., and Sedighi, K. (2013). Experimental analysis of heat transfer enhancement in shell and helical tube heat exchangers. Appl. Therm. Eng. 51: 644–652, https://doi.org/10.1016/j.applthermaleng.2012.10.008.Search in Google Scholar
Janssen, L.A.M. and Hoogendoorn, C.J. (1978). Laminar convective heat transfer in helical coiled tubes. Int. J. Heat Mass Tran. 21: 1197–1206, https://doi.org/10.1016/0017-9310(78)90138-2.Search in Google Scholar
Jayakumar, J.S., Mahajani, S.M., Mandal, J.C., Vijayan, P.K., and Bhoi, R. (2008). Experimental and CFD estimation of heat transfer in helically coiled heat exchangers. Chem. Eng. Res. Des. 8: 221–232, https://doi.org/10.1016/j.cherd.2007.10.021.Search in Google Scholar
Jayakumar, J.S., Mahajani, S.M., Mandal, J.C., Iyer, K.N., and Vijayan, P.K. (2010). CFD analysis of single-phase flows inside helically coiled tubes. Comput. Chem. Eng. 34: 430–446, https://doi.org/10.1016/j.compchemeng.2009.11.008.Search in Google Scholar
Jeschke, D. (1925). Heat transfer and pressure loss in coiled pipes. Ergaenzungsheft Z. Ver. Disch. Ing. 68: 24–28.Search in Google Scholar
Ju, H., Huang, Z., Xu, Y., Duan, B., and Yu, Y. (2001). Hydraulic performance of small bending radius helical coil-pipe. J. Nucl. Sci. Technol. 38: 826–831, https://doi.org/10.1080/18811248.2001.9715102.Search in Google Scholar
Kahani, M., Heris, S.Z., and Mousavi, S.M. (2013a). Comparative study between metal oxide nanopowders on thermal characteristics of nanofluid flow through helical coils. Powder Technol. 246: 82–92, https://doi.org/10.1016/j.powtec.2013.05.010.Search in Google Scholar
Kahani, M., Heris, S.Z., and Mousavi, S.M. (2013b). Effects of curvature ratio and coil pitch spacing on heat transfer performance of Al2O3/water nanofluid laminar flow through helical coils. J. Dispersion Sci. Technol. 34: 1704–1712, https://doi.org/10.1080/01932691.2013.764485.Search in Google Scholar
Kalb, C.E. and Seader, J.D. (1972). Heat and mass transfer phenomena for viscous flow in curved circular tubes. Int. J. Heat Mass Tran. 15: 801–817, https://doi.org/10.1016/0017-9310(72)90122-6.Search in Google Scholar
Kannadasan, N., Ramanathan, K., and Suresh, S. (2012). Comparison of heat transfer and pressure drop in horizontal and vertical helically coiled heat exchanger with CuO/water based nano fluids. Exp. Therm. Fluid Sci. 42: 64–70, https://doi.org/10.1016/j.expthermflusci.2012.03.031.Search in Google Scholar
Karmankar, R.G. (2017). Enhancement of heat transfer rate by using helix tube and friction factor. Int. Res. J. Eng. Technol. 4: 341–346.Search in Google Scholar
Khairul, M.A., Hossain, A., Saidur, R., and Alim, M.A. (2013). Prediction of heat transfer performance of CuO/water nanofluids flow in spirally corrugated helically coiled heat exchanger using fuzzy logic technique. Comput. Fluids 100: 123–129, https://doi.org/10.1016/j.ijheatmasstransfer.2013.08.030.Search in Google Scholar
Khorasani, S., Jafarmadar, S., Pourhedayat, S., Abdollahi, M.A.A., and Heydarpour, A. (2019). Experimental investigations on the effect of geometrical properties of helical wire turbulators on thermal performance of a helically coiled tube. Appl. Therm. Eng. 147: 983–990, https://doi.org/10.1016/j.applthermaleng.2018.09.092.Search in Google Scholar
Korane, A.B., Purandare, P.S., and Mali, K.V. (2012). Heat transfer analysis of helical coil heat exchanger with circular and square coiled pattern. Int. J. Eng. Sci. Res. 2: 413–423.Search in Google Scholar
Kubair, V. and Kuloor, N.R. (1966). Heat transfer to Newtonian fluids in coiled pipes in laminar flow. Int. J. Heat Mass Tran. 9: 63–75, https://doi.org/10.1016/0017-9310(66)90057-3.Search in Google Scholar
Kubair, V. and Varrier, C.B.S. (1961). Pressure drop for liquid flow in helical coils. Trans. Indian Inst. Chem. Eng. 14: 93–97.Search in Google Scholar
Kulkarni, H.R., Dhanasekaran, C., Rathnakumar, P., and Sivaganesan, S. (2021). Experimental study on thermal analysis of helical coil heat exchanger using Green synthesis silver nanofluid. Mater. Today Proc. 42: 1037–1042, https://doi.org/10.1016/j.matpr.2020.12.087.Search in Google Scholar
Kumar, E.P., Solanki, A.K., and Kumar, M.M.J. (2021). Numerical investigation of heat transfer and pressure drop characteristics in the micro-fin helically coiled tubes. Appl. Therm. Eng. 182: 1–14, https://doi.org/10.1016/j.applthermaleng.2020.116093.Search in Google Scholar
Kurnia, J.C., Chaedir, B.A., and Sasmito, A.P. (2020). Laminar convective heat transfer in helical tube with twisted tape insert. Int. J. Heat Mass Tran. 150: 119309, https://doi.org/10.1016/j.ijheatmasstransfer.2020.119309.Search in Google Scholar
Kutateladze, S.S. and Borishanskii, V.M. (1966). A concise encyclopedia of heat transfer, 1st ed. Pergamon Press, Oxford, New York.Search in Google Scholar
Li, Y., Wu, J., Wang, H., Kou, L., and Tian, X. (2012). Fluid flow and heat transfer characteristics in helical tubes cooperating with spiral corrugation. Energy Procedia 17: 791–800, https://doi.org/10.1016/j.egypro.2012.02.172.Search in Google Scholar
Liaw, K.L., Kurnia, J.C., and Sasmito, A.P. (2021). Turbulent convective heat transfer in helical tube with twisted tape insert. Int. J. Heat Mass Tran. 169: 120918, https://doi.org/10.1016/j.ijheatmasstransfer.2021.120918.Search in Google Scholar
Liu, S. and Masliyah, J.H. (1993). Axially invariant laminar flow in helical pipes with a finite pitch. J. Fluid Mech. 251: 315–353, https://doi.org/10.1017/S002211209300343X.Search in Google Scholar
Maghrabie, H.M., Attalla, M., and Mohsen, A.A.A. (2021a). Performance of a shell and helically coiled tube heat exchanger with variable inclination angle: experimental study and sensitivity analysis. Int. J. Therm. Sci. 164: 106869, https://doi.org/10.1016/j.ijthermalsci.2021.106869.Search in Google Scholar
Maghrabie, H.M., Attalla, M., and Mohsen, A.A.A. (2021b). Performance assessment of a shell and helically coiled tube heat exchanger with variable orientations utilizing different nanofluids. Appl. Therm. Eng. 182: 1–16, https://doi.org/10.1016/j.applthermaleng.2020.116013.Search in Google Scholar
Mahdi, Q.S., Fattah, S.A., and Jasim, O.M. (2014). Experimental and numerical investigation to enhance the performance of helical coiled tube heat exchanger by using turbulators. J. Eng. Dev. 18: 1–16.Search in Google Scholar
Mahmoudi, M., Tavakoli, M.R., Mirsoleimani, M.M., Gholami, A., and Salimpour, M.A. (2016). Experimental and numerical investigation on forced convection heat transfer and pressure drop in helically coiled pipes using TiO2/water nanofluid. Int. J. Refrig. 74: 627–643, https://doi.org/10.1016/j.ijrefrig.2016.11.014.Search in Google Scholar
Manlapaz, R.L. and Churchill, S.W. (1980). Fully developed laminar flow in a helically coiled tube of finite pitch. Chem. Eng. Commun. 7: 57–78, https://doi.org/10.1080/00986448008912549.Search in Google Scholar
Mikaila, V.A. and Poskas, P.S. (1990). Local heat transfer in coiled tubes at high heat fluxes, 1. Heat Transfer Sov. Res. 22: 713–727.Search in Google Scholar
Mirfendereski, S., M., Abbasi, A., and Saffar-Avval, M. (2015). Experimental and numerical investigation of nanofluid heat transfer in helically coiled tubes at constant wall heat flux. Adv. Powder Technol. 26: 1483–1494, https://doi.org/10.1016/j.apt.2015.08.006.Search in Google Scholar
Mirgolbabaei, H. (2018). Numerical investigation of vertical helically coiled tube heat exchangers. Appl. Therm. Eng. 136: 252–259, https://doi.org/10.1016/j.applthermaleng.2018.02.061.Search in Google Scholar
Mishra, P. and Gupta, S.N. (1979). Momentum transfer in curved pipes. 1. Newtonian fluids, Ind. Eng. Chem. Process Des. Dev 18: 130–137, https://doi.org/10.1021/i260069a017.Search in Google Scholar
Mori, Y. and Narayama, W. (1967). Study on forced convective heat transfer in curved pipes. Int. J. Heat Mass Tran. 10: 681–695, https://doi.org/10.1016/0017-9310(67)90182-2.Search in Google Scholar
Nashine, P., Singh, T.S., Rajak, U., and Verma, T.N. (2020). Effect of de on the heat transfer characteristics of a helical coil tube with variable velocity & pressure inlet. J. Therm. Eng. 6: 128–139, https://doi.org/10.18186/thermal.729149.Search in Google Scholar
Niwalkar, A.F., Kshirsagar, J.M., and Kulkarni, K. (2019). Experimental investigation of heat transfer enhancement in shell and helically coiled tube heat exchanger using SiO2/water nanofluids. Mater. Today Proc. 18: 947–962, https://doi.org/10.1016/j.matpr.2019.06.532.Search in Google Scholar
Panahi, D. and Zamzamian, K. (2016). Heat transfer enhancement of shell-and-coiled tube heat exchanger utilizing helical wire turbulator. Appl. Therm. Eng. 115: 607–615, https://doi.org/10.1016/j.applthermaleng.2016.12.128.Search in Google Scholar
Pattison, M. (2011). Secondary flows [Online] thermopedia.com, http://thermopedia.com/content/1113 (Accessed 10 May 2021).Search in Google Scholar
Pawar, S.S. and Sunnapwar, V.K. (2014). Experimental and CFD investigation of convective heat transfer in helically coiled tube heat exchanger. Chem. Eng. Res. Des. 92: 2294–2312, https://doi.org/10.1016/j.cherd.2014.01.016.Search in Google Scholar
Pimenta, T.A. and Campos, J.B.L.M. (2012). Friction losses of Newtonian and non-Newtonian fluids flowing in laminar regime in a helical coil. Exp. Therm. Fluid Sci. 36: 194–204, https://doi.org/10.1016/j.ijheatmasstransfer.2012.10.078.Search in Google Scholar
Pimenta, T.A. and Campos, J.B.L.M. (2013). Heat transfer coefficents from Newtonian and non-Newtonian fluids flowing in laminar regime in a helical coil. Int. J. Heat Mass Tran. 58: 676–690, https://doi.org/10.1016/j.ijheatmasstransfer.2012.10.078.Search in Google Scholar
Prabhanjan, D.G., Raghavan, G.S.V., and Rennie, T.J. (2002). Comparison of heat transfer rates between a straight tube heat exchanger and a helically coiled heat exchanger. Int. Commun. Heat Mass Tran. 29: 185–191, https://doi.org/10.1016/S0735-1933(02)00309-3.Search in Google Scholar
Prasad, B.V.S.S.S., Das, D.H., and Prabhakar, A.K. (1988). Pressure drop, heat transfer and performance of a helically coiled tubular exchanger. Heat Recovery Syst. CHP 9: 249–256, https://doi.org/10.1016/0890-4332(89)90008-2.Search in Google Scholar
Puttewar, A.S. and Andhare, A.M. (2015). Design and thermal evaluation of shell and helical coil heat exchanger. Int. J. Renew. Energy Technol. 4: 416–423.10.15623/ijret.2015.0401064Search in Google Scholar
Radkar, R.N., Bhanvase, B.A., Barai, D.P., and Sonawane, S.H. (2019). Intensified convective heat transfer using ZnO nanofluids in heat exchanger with helical coiled geometry at constant wall temperature. Mater. Sci. Energy Technol. 2: 161–170, https://doi.org/10.1016/j.mset.2019.01.007.Search in Google Scholar
Rainieri, S., Bozzoli, F., Cattani, L., and Pagliarini, G. (2013). Compound convective heat transfer enhancement in helically coiled wall corrugated tubes. Int. J. Heat Mass Tran. 59: 353–362, https://doi.org/10.1016/j.ijheatmasstransfer.2012.12.037.Search in Google Scholar
Rogers, G.F.C. and Mayhew, Y.R. (1964). Heat transfer and pressure loss in helically coiled tubes with turbulent flow. Int. J. Heat Mass Tran. 7: 1207–1216, https://doi.org/10.1016/0017-9310(64)90062-6.Search in Google Scholar
Sahin, F. and Namli, L. (2018). Importance of stability of nanofluid in terms of improving heat transfer. Omer Halisdemir Univ. J. Eng. Sci. 7: 880–898, https://doi.org/10.28948/ngumuh.445339.Search in Google Scholar
Salem, M.R., Elshazly, K.M., Sakr, R.Y., and Ali, R.K. (2015). Experimental investigation of coil curvature effect on heat transfer and pressure drop characteristics of shell and coil heat exchanger. J. Therm. Sci. Eng. Appl. 7: 1–9, https://doi.org/10.1115/1.4028612.Search in Google Scholar
Salimpour, M.R. (2009). Heat transfer coefficients of shell and coiled tube heat exchangers. Exp. Therm. Fluid Sci. 33: 203–207, https://doi.org/10.1016/j.expthermflusci.2008.07.015.Search in Google Scholar
Schmidt, E.F. (1967). Warmeübergang und Druckverlust in Rohrschlangen. Chem. Ing. Tech. 39: 781–789, https://doi.org/10.1002/cite.330391302.Search in Google Scholar
Seban, R.A. and Mclaughlin, E.F. (1963). Heat transfer in tube coils with laminar and turbulent flow. Int. J. Heat Mass Tran. 6: 387–395, https://doi.org/10.1016/0017-9310(63)90100-5.Search in Google Scholar
Sepehr, M., Hashemi, S.S., Rahjoo, M., Farhangmehr, V., and Alimoradi, A. (2018). Prediction of heat transfer, pressure drop and entropy generation in shell and helically coiled finned tube heat exchangers. Chem. Eng. Res. Des. 134: 277–291, https://doi.org/10.1016/j.cherd.2018.04.010.Search in Google Scholar
Sharma, P., Gupta, R., and Wanchoo, R.K. (2016). Hydrodynamic studies on glycol based Al2O3 nanofluid flowing through straight tubes and coils. Exp. Therm. Fluid Sci. 82: 19–31, https://doi.org/10.1016/j.expthermflusci.2016.11.001.Search in Google Scholar
Shokouhmand, H., Salimpour, M.R., and Akhavan-Behabadi, M.A. (2007). Experimental investigation of shell and coiled tube heat exchangers using Wilson plots. Int. Commun. Heat Mass Tran. 35: 84–92, https://doi.org/10.1016/j.icheatmasstransfer.2007.06.001.Search in Google Scholar
Singh, H., Suzuki, T., Washiashi, J., Ichiyanagi, M. and Liu, J. (2018). SAE technical paper: influence of secondary flow generation on heat transfer inside the fin type spiral sub-cooled condenser by experimental and CFD analysis, pp. 1–11, https://doi.org/10.4271/2018-32-0054.Search in Google Scholar
Singh, P., Sharma, P., Gupta, R., and Wanchoo, R.K. (2018). Heat transfer characteristics of propylene glycol/water based magnesium oxide nanofluid flowing through straight tubes and helical coils. J. Therm. Eng. 4: 1737–1755, https://doi.org/10.18186/journal-of-thermal-engineering.369007.Search in Google Scholar
Sreejith, K., Ram, T.R.S., Varghese, J.A., Francis, M., Mossas, V.J., Nidhin, M.J., Nithil, E.S., and Sushmitha, S. (2015). Experimental investigation of a helical coil heat exchanger. Res. Inventy Int. J. Eng. Sci. 5: 1–5.Search in Google Scholar
Srinivas, T. and Vinod, A.V. (2016). Heat transfer intensification in a shell and helical coil heat exchanger using water-based nanofluids. Chem. Eng. Process 102: 1–8, https://doi.org/10.1016/j.cep.2016.01.005.Search in Google Scholar
Srinivasan, P.S., Nandapurkar, S.S., and Holland, F.A. (1968). Pressure drop and heat transfer in coils. Chem. Eng. 218.Search in Google Scholar
Thomson, J. (1876). On the origin of windings of river and alluvial planes, with remarks on the flow of water round bends in pipes. Proc. Roy. Soc. Lond. 25: 5–8, https://doi.org/10.1098/rspl.1876.0004.Search in Google Scholar
Tuncer, A.D., Sozen, A., Khanlari, A., Gurbuz, E.Y., and Variyenli, H.I. (2021). Upgrading the performance of a new shell and helically coiled heat exchanger by using longitudinal fins. Appl. Therm. Eng. 191: 116876, https://doi.org/10.1016/j.applthermaleng.2021.116876.Search in Google Scholar
Wang, J., Hashemi, S.S., Alahgholi, S., Mehri, M., Safarzadeh, M., and Alimoradi, A. (2018). Analysis of exergy and energy in shell and helically coiled finned tube heat exchangers and design optimization. Int. J. Refrig. 94: 11–23, https://doi.org/10.1016/j.ijrefrig.2018.07.028.Search in Google Scholar
Wang, M., Zheng, M., Wang, R., Tian, L., Ye, C., Chen, Y., and Gu, H. (2019). Experimental studies on local and average heat transfer characteristics in helical pipes with single phase flow. Ann. Nucl. Energy 123: 78–85, https://doi.org/10.1016/j.anucene.2018.09.017.Search in Google Scholar
Wei, H., Moria, H., Nisar, K.S., Ghandour, R., Issakhov, A., Sun, Y.L., Kaood, Y., and Youshanlouei, M.M. (2021). Effect of volume fraction and size of Al2O3 nanoparticles in thermal, frictional and economic performance of circumferential corrugated helical tube. Case Stud. Therm. Eng. 25: 100948, https://doi.org/10.1016/j.csite.2021.100948.Search in Google Scholar
White, C.M. (1929). Streamline flow through curved pipes. Proc. Roy. Soc. Lond. Ser. A 123: 645–663, https://doi.org/10.1098/rspa.1929.0089.Search in Google Scholar
Williams, G.S., Hubbell, C.W., and Fenkell, G.H. (1902). Experiments at Detroit, Michigan on the effect of curvature on the flow of water pipes. Trans. Am. Soc. Civ. Eng. 47: 1–196, https://doi.org/10.1061/taceat.0001496.Search in Google Scholar
Wu, S.Y., Chen, S.J., and Li, Y.R. (2009). Numerical investigation of turbulent flow, heat transfer and entropy generation in a helical coiled tube with larger curvature ratio. Heat Mass Tran. 45: 569–578, https://doi.org/10.1007/s00231-008-0458-5.Search in Google Scholar
Xin, R.C. and Ebadian, M.A. (1997). The effects of Prandtl numbers on local and average convective heat transfer characteristics in helical pipes. J. Heat Tran. 119: 467–473, https://doi.org/10.1115/1.2824120.Search in Google Scholar
Zachár, A. (2010). Analysis of coiled-tube heat exchangers to improve heat transfer rate with spirally corrugated wall. Int. J. Heat Mass Tran. 53: 3928–3939, https://doi.org/10.1016/j.ijheatmasstransfer.2010.05.011.Search in Google Scholar
Zhai, X., Qi, C., Pan, Y., Luo, T., and Liang, L. (2019). Effects of screw pitches and rotation angles on flow and heat transfer characteristics of nanofluids in spiral tubes. Int. J. Heat Mass Tran. 130: 989–1003, https://doi.org/10.1016/j.ijheatmasstransfer.2018.10.131.Search in Google Scholar
Zheng, L., Xie, Y., and Zhang, D. (2018). Numerical investigation on heat transfer and flow characteristics in helically coiled mini-tubes equipped with dimples. Int. J. Heat Mass Tran. 126: 544–570, https://doi.org/10.1016/j.ijheatmasstransfer.2018.05.111.Search in Google Scholar
Zhu, H., Wang, H., and Kou, G. (2014). Experimental study on the heat transfer enhancement by Dean Vortices in spiral tubes. Int. J. Energy Environ. 5: 317–326.Search in Google Scholar
© 2021 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- Single-phase flow heat transfer characteristics in helically coiled tube heat exchangers
- Design and optimization of an integrated gamma ray scanning system for the uranium sample
- Numerical simulation of the effect of rod bowing on critical heat flux
- Flow and heat transfer characteristics of a nanofluid as the coolant in a typical MTR core
- Mathematical modeling of point kinetic equations with temperature feedback for reactivity transient analysis in MTR
- An enhanced formalism for the inverse reactor kinetics problem
- The establishment of analysis methodology of NRCDose3 for Kuosheng nuclear power plant decommissioning
- Analysis of SMART reactor core with uranium mononitride for prolonged fuel cycle using OpenMC
- Conceptual design of an innovative I&XC fuel assembly for a SMR based on neutronic/thermal-hydraulic calculations at the BOC
- Optimized fractional-order PID controller based on nonlinear point kinetic model for VVER-1000 reactor
- High rate X-ray radiation shielding ability of cement-based composites incorporating strontium sulfate (SrSO4) minerals
- Vibration analysis for predictive maintenance and improved reliability of rotating machines in ETRR-2 research reactor
- Calendar of events
Articles in the same Issue
- Frontmatter
- Single-phase flow heat transfer characteristics in helically coiled tube heat exchangers
- Design and optimization of an integrated gamma ray scanning system for the uranium sample
- Numerical simulation of the effect of rod bowing on critical heat flux
- Flow and heat transfer characteristics of a nanofluid as the coolant in a typical MTR core
- Mathematical modeling of point kinetic equations with temperature feedback for reactivity transient analysis in MTR
- An enhanced formalism for the inverse reactor kinetics problem
- The establishment of analysis methodology of NRCDose3 for Kuosheng nuclear power plant decommissioning
- Analysis of SMART reactor core with uranium mononitride for prolonged fuel cycle using OpenMC
- Conceptual design of an innovative I&XC fuel assembly for a SMR based on neutronic/thermal-hydraulic calculations at the BOC
- Optimized fractional-order PID controller based on nonlinear point kinetic model for VVER-1000 reactor
- High rate X-ray radiation shielding ability of cement-based composites incorporating strontium sulfate (SrSO4) minerals
- Vibration analysis for predictive maintenance and improved reliability of rotating machines in ETRR-2 research reactor
- Calendar of events