Home Effect of chain branching on the rheological properties of HDPE/LLDPE and HDPE/LDPE blends under shear and elongational flows and evaluation of die swell and flow instabilities
Article
Licensed
Unlicensed Requires Authentication

Effect of chain branching on the rheological properties of HDPE/LLDPE and HDPE/LDPE blends under shear and elongational flows and evaluation of die swell and flow instabilities

  • Daniel Muller Gomes de Freitas , Milena Heloísa Araújo Silva , Shirley Nóbrega Cavalcanti , Rafael Braga da Cunha EMAIL logo , Pankaj Agrawal , Gustavo de Figueiredo Brito and Tomás Jeferson Alves de Mélo EMAIL logo
Published/Copyright: March 24, 2025
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Polymer Processing
From the journal International Polymer Processing Volume 40 Issue 2

Abstract

Depending on the conditions of polymer synthesis, polyethylene can exhibit various molecular structures, such as long and short-chain branching, which influence its molecular weight and molecular weight distribution. The molecular structure of polyethylene in the blend significantly impacts its properties, making it essential to study these effects on the blend’s final properties. Based on the above, this work aims to investigate the effects of 1-hexene short chain branching (SCB) of linear low-density polyethylene (LLDPE) and long chain branching (LCB) of low-density polyethylene (LDPE) polymers on the rheological properties and processing of blends with high-density polyethylene (HDPE). LDPE showed higher complex viscosity at low frequencies and stronger shear thinning behavior than HDPE and LLDPE-H polymers. The strong shear thinning behavior of LDPE may be related to its higher molecular weight and presence of LCB. Capillary rheometry tests demonstrated a shear-thinning behavior for both the pure polymers and the blends, with the results for the blends being lower than those for the pure polymers, following the direct mixing rule. LDPE exhibited lower viscosity compared to HDPE, LLDPE-H, and all the blends, corroborating the observed results in complex viscosity at high deformation values. As for the flow instabilities, the occurrence of these instabilities at high shear rates was observed for all the polymers investigated in this study. Two methods were used to measure the swell of the extrudate (in-line and off-line), and both methods were efficient in describing the swell behavior as a function of shear rate. The elongational viscosity of the LDPE was found to exhibit “strain hardening” behavior, i.e., an increase in elongational viscosity with increasing strain and time.

Keywords: polyethylene; chain branching; polymer blends; shear and elongational flows; flow instabilities
Corresponding authors: Rafael Braga da Cunha and Tomás Jeferson Alves de Mélo, Department of Materials Engineering, Federal University of Campina Grande (UFCG), Campina Grande, Paraiba, 58429-900, Brazil, E-mail: (R.B. da Cunha), (T.J.A. de Mélo).

Funding source: CAPES and CNPq

Award Identifier / Grant number: TJAM—Grant Numbers 577061/20089/Jovens Pesquisadores-Nanotecnologia, 483743/20119/UNIVERSAL and 426191/20161/UNIVERSAL

Acknowledgments

The authors thank CAPES and CNPq (TJAM – Grant Numbers: 577061/20089/Jovens Pesquisadores-Nanotecnologia, 483743/20119/UNIVERSAL and 426191/20161/UNIVERSAL) for financial support.

  1. Research ethics: Not applicable.

  2. Informed consent: Not applicable.

  3. Author contributions: Daniel Muller: formal analysis (equal); resources (equal); supervision (equal); writing – review and editing (equal). Milena Heloísa: formal analysis (equal); resources (equal); supervision (equal); writing – review and editing (equal). Shirley N. Cavalcanti: methodology (supporting); software (equal). Rafael Braga da Cunha: investigation (equal); methodology (supporting); software (equal); validation (equal). Pankaj Agrawal: methodology (equal); supervision (equal). writing – original draft (equal); writing – review and editing (equal). Gustavo de Figueiredo Brito: conceptualization (equal); methodology (equal); supervision (equal); Tomas Jeferson Alves de Mélo: resources (equal); supervision (equal); writing – review and editing (equal). The authors have accepted responsibility for the entire content of this manuscript and approved its submission.

  4. Use of Large Language Models, AI and Machine Learning Tools: None declared.

  5. Conflict of interest: The authors declare that there are no conflicts of interest.

  6. Research funding: Conselho Nacional de Desenvolvimento Científico e Tecnológico-CNPq (TJAM – Grant Numbers: 577061/20089, 483743/20119/UNIVERSAL and 426191/20161).

  7. Data availability: Not applicable.

References

Agassant, J.-F., Avenas, P., Carreau, P.J., Vergnes, B., and Vincent, M. (2017). Polymer processing. Polym. Process: I–XLI, https://doi.org/10.3139/9781569906064.FM.Search in Google Scholar

Agrawal, P., Silva, M.H.A., Cavalcanti, S.N., Freitas, D.M.G., Araújo, J.P., Oliveira, A.D.B., and Mélo, T.J.A. (2022). Rheological properties of high-density polyethylene/linear low-density polyethylene and high-density polyethylene/low-density polyethylene blends. Polym. Bull. 79: 2321–2343, https://doi.org/10.1007/S00289-021-03635-8/FIGURES/15.Search in Google Scholar

Allal, A., Lavernhe, A., Vergnes, B., and Marin, G. (2006). Relationships between molecular structure and sharkskin defect for linear polymers. J. NonNewton Fluid Mech. 134: 127–135, https://doi.org/10.1016/j.jnnfm.2005.12.010.Search in Google Scholar

Ansari, M., Hatzikiriakos, S.G., and Mitsoulis, E. (2012a). Slip effects in HDPE flows. J. NonNewton Fluid Mech. 167–168: 18–29, https://doi.org/10.1016/j.jnnfm.2011.09.007.Search in Google Scholar

Ansari, M., Inn, Y.W., Sukhadia, A.M., DesLauriers, P.J., and Hatzikiriakos, S.G. (2012b). Melt fracture of HDPEs: metallocene versus Ziegler-Natta and broad MWD effects. Polymer (Guildford) 53: 4195–4201, https://doi.org/10.1016/j.polymer.2012.07.030.Search in Google Scholar

Ansari, M., Inn, Y.W., Sukhadia, A.M., DesLauriers, P.J., and Hatzikiriakos, S.G. (2013). Wall slip of HDPEs: molecular weight and molecular weight distribution effects. J. Rheol. (N. Y. N. Y.) 57: 927–948, https://doi.org/10.1122/1.4801758.Search in Google Scholar

Arrigo, R., Malucelli, G., and La Mantia, F.P. (2021) Effect of the elongational flow on the morphology and properties of polymer systems: a brief review. Polymers 13: 3529. https://doi.org/10.3390/POLYM13203529.Search in Google Scholar

Barczewski, M., Barczewski, R., and Chwalczuk, T. (2020). The in-line detection method of sharkskin melt flow instability during polyethylene extrusion based on pressure analysis. J. Manuf. Process 59: 153–166, https://doi.org/10.1016/J.JMAPRO.2020.09.046.Search in Google Scholar

Behzadfar, E., Ansari, M., Konaganti, V.K., and Hatzikiriakos, S.G. (2015). Extrudate swell of HDPE melts: I. Experimental. J. NonNewton Fluid Mech. 225: 86–93, https://doi.org/10.1016/J.JNNFM.2015.07.008.Search in Google Scholar

Carreau, P.J., Bousmina, M., and Ajji, A. (1994). Rheological properties of blends: facts and challenges. Prog. Pacific Polym. Sci. 3: 25–39, https://doi.org/10.1007/978-3-642-78759-1_3.Search in Google Scholar

Cho, K., Lee, B.H., Hwang, K.M., and Choe, S. (1998). Rheological and mechanical properties in polyethylene blends. Polym. Eng. Sci. 38: 1969–1975, https://doi.org/10.1002/pen.10366.Search in Google Scholar

Combeaud, C., Vergnes, B., Merten, A., Hertel, D., and Münstedt, H. (2007). Volume defects during extrusion of polystyrene investigated by flow induced birefringence and laser-Doppler velocimetry. J. NonNewton Fluid Mech. 145: 69–77, https://doi.org/10.1016/J.JNNFM.2007.01.002.Search in Google Scholar

Dartora, P.C., Santana, R.M.C., and Moreira, A.C.F. (2015). The influence of long chain branches of LLDPE on processability and physical properties. Polimeros 25: 531–539, https://doi.org/10.1590/0104-1428.1732.Search in Google Scholar

Ebrahimi, M., Tomkovic, T., Liu, G., Doufas, A.A., and Hatzikiriakos, S.G. (2018). Melt fracture of linear low-density polyethylenes: die geometry and molecular weight characteristics. Phys. Fluids 30, https://doi.org/10.1063/1.5029380/906864.Search in Google Scholar

Fang, Y., Carreau, P.J., and Lafleur, P.G. (2005). Thermal and rheological properties of mLLDPE/LDPE blends. Polym. Eng. Sci. 45: 1254–1264, https://doi.org/10.1002/PEN.20401.Search in Google Scholar

Freitas, D.M.G., Oliveira, A.D.B., Alves, A.M., Cavalcanti, S.N., Agrawal, P., and Mélo, T.J.A. (2020). Linear low-density polyethylene/high-density polyethylene blends: effect of high-density polyethylene content on die swell and flow instability. J. Appl. Polym. Sci. 138: e49910, https://doi.org/10.1002/app.49910.Search in Google Scholar

Ganvir, V., Gautham, B.P., Pol, H., Bhamla, M.S., Sclesi, L., Thaokar, R., Lele, A., and Mackley, M. (2011). Extrudate swell of linear and branched polyethylenes: ALE simulations and comparison with experiments. J. NonNewton Fluid Mech. 166: 12–24, https://doi.org/10.1016/J.JNNFM.2010.10.001.Search in Google Scholar

Georgantopoulos, C.K., Esfahani, M.K., Naue, I.F.C., Wilhelm, M., and Kádár, R. (2023). Role of molecular architecture and temperature on extrusion melt flow instabilities of two industrial LLDPE and LDPE polyethylenes investigated by capillary rheology, high-pressure sensitivity slit die and optical analysis. J. Appl. Polym. Sci. 140: e53165, https://doi.org/10.1002/APP.53165.Search in Google Scholar

Gotsis, A.D., Zeevenhoven, B.L.F., and Tsenoglou, C. (2004). Effect of long branches on the rheology of polypropylene. J. Rheol. (N. Y. N. Y.) 48: 895–914, https://doi.org/10.1122/1.1764823.Search in Google Scholar

Hameed, T. and Hussein, I.A. (2006). Melt miscibility and mechanical properties of metallocene LLDPE blends with HDPE: influence of Mw of LLDPE. Polym. J. 38: 1114–1126, https://doi.org/10.1295/polymj.PJ2005254.Search in Google Scholar

Huang, J.C. and Leong, K.S. (2002). Shear viscosity, extensional viscosity, and die swell of polypropylene in capillary flow with pressure dependency. J. Appl. Polym. Sci. 84: 1269–1276, https://doi.org/10.1002/APP.10466.Search in Google Scholar

Hussein, I.A. (2003). Influence of composition distribution and branch content on the miscibility of m-LLDPE and HDPE blends: rheological investigation. Macromolecules 36: 2024–2031, https://doi.org/10.1021/ma0257245.Search in Google Scholar

Karbashewski, E., Kale, L., Rudin, A., and Tchir, W.J. (1993). Effects of additions of high-density polyethylene on the processability of linear low-density polyethylene. J. Appl. Polym. Sci 47: 1143–1154.10.1002/app.1993.070470702Search in Google Scholar

Kida, T., Doi, Y., Tanaka, R., Uneyama, T., Shiono, T., and Masubuchi, Y. (2021). Rheological properties of linear and short-chain branched polyethylene with nearly monodispersed molecular weight distribution. Rheol. Acta 60: 511–519, https://doi.org/10.1007/S00397-021-01286-0/FIGURES/8.Search in Google Scholar

Konaganti, V.K., Ansari, M., Mitsoulis, E., and Hatzikiriakos, S.G. (2015). Extrudate swell of a high-density polyethylene melt: II. Modeling using integral and differential constitutive equations. J. NonNewton Fluid Mech. 225: 94–105, https://doi.org/10.1016/J.JNNFM.2015.07.005.Search in Google Scholar

Liang, J.Z. (2019). Melt strength and drawability of HDPE, LDPE and HDPE/LDPE blends. Polym. Test. 73: 433–438, https://doi.org/10.1016/J.POLYMERTESTING.2018.12.007.Search in Google Scholar

Liang, J.Z., Li, R.K.Y., and Tjong, S.C. (1998). Melt flow properties of LDPE/HDPE blends in capillary extrusion. Int. Polym. Process. 13: 46–49, https://doi.org/10.3139/217.980046/MACHINEREADABLECITATION/RIS.Search in Google Scholar

Liu, C., Wang, J., and He, J. (2002). Rheological and thermal properties of m-LLDPE blends with m-HDPE and LDPE. Polymer (Guildford) 43: 3811–3818, https://doi.org/10.1016/S0032-3861(02)00201-X.Search in Google Scholar

Münstedt, H. (2020). Recoverable extensional flow of polymer melts and its relevance for processing. Polymers 12: 1512, https://doi.org/10.3390/POLYM12071512.Search in Google Scholar PubMed PubMed Central

Münstedt, H., Steffl, T., and Malmberg, A. (2005). Correlation between rheological behaviour in uniaxial elongation and film blowing properties of various polyethylenes. Rheol. Acta 45: 14–22, https://doi.org/10.1007/S00397-005-0435-6/FIGURES/9.Search in Google Scholar

Oliveira, A.D.B., Freitas, D.M.G., Araújo, J.P., Cavalcanti, S.N., Câmara, D.S., Agrawal, P., and Mélo, T.J.A. (2020). HDPE/LLDPE blends: rheological, thermal, and mechanical properties. Mater. Res. Innov. 24: 289–294, https://doi.org/10.1080/14328917.2019.1655623.Search in Google Scholar

Osswald, T. and Rudolph, N. (2014). Polymer rheology. Polym. Rheol.: I–XI, https://doi.org/10.3139/9781569905234.FM.Search in Google Scholar

Pashazadeh, S., Aulova, A., Georgantopoulos, C.K., Bek, M., Vittorias, I., Naue, I.F., Wilhelm, M., and Kádár, R. (2023). An intriguing array of extrudate patterns in long-chain branched polymers during extrusion. Macromol. Mater. Eng. 308: 2300088, https://doi.org/10.1002/MAME.202300088.Search in Google Scholar

Peacock, A. (2000). Handbook of polyethylene: structures: properties, and applications. Handb. Polyethyl. 1: 1–544, https://doi.org/10.1201/9781482295467.Search in Google Scholar

Sarkhel, G., Banerjee, A., and Bhattacharya, P. (2006). Rheological and mechanical properties of LDPE/HDPE blends. Polym. Plast. Technol. Eng. 45: 713–718, https://doi.org/10.1080/03602550600609663.Search in Google Scholar

Shaidullin, N.M., Salakhov, I.I., Borisenko, V.N., Tavtorkin, A.N., and Nifant’ev, I.E. (2020). Structural, rheological, and mechanical properties of binary compounds based on high-density polyethylene and linear low-density polyethylene. Russ. J. Appl. Chem. 93: 1179–1187, https://doi.org/10.1134/S1070427220080108/TABLES/7.Search in Google Scholar

Stadler, F.J. and Mahmoudi, T. (2011). Understanding the effect of short-chain branches by analyzing viscosity functions of linear and short-chain branched polyethylenes. Korea Aust. Rheol. J. 23: 185–193, https://doi.org/10.1007/s13367-011-0023-5.Search in Google Scholar

Tang, D., Marchesini, F.H., Cardon, L., and D’hooge, D.R. (2020). State of the-art for extrudate swell of molten polymers: from fundamental understanding at molecular scale toward optimal die design at final product scale. Macromol. Mater. Eng. 305: 2000340, https://doi.org/10.1002/MAME.202000340.Search in Google Scholar

Tang, D., Marchesini, F.H., D’hooge, D.R., and Cardon, L. (2019). Isothermal flow of neat polypropylene through a slit die and its die swell: bridging experiments and 3D numerical simulations. J. NonNewton Fluid Mech. 266: 33–45, https://doi.org/10.1016/J.JNNFM.2019.02.004.Search in Google Scholar

Venet, C. and Vergnes, B. (1997). Experimental characterization of sharkskin in polyethylenes. J. Rheol. (N. Y. N. Y.) 41: 873–892, https://doi.org/10.1122/1.550837.Search in Google Scholar

Vergnes, B. (2015). Extrusion defects and flow instabilities of molten polymers. Int. Polym. Process. 30: 3–28, https://doi.org/10.3139/217.3011/XML.Search in Google Scholar

Wang, S., Drda, P.A., and Inn, Y. (1996). Exploring molecular origins of sharkskin, partial slip, and slope change in flow curves of linear low density polyethylene. J. Rheol. (N. Y. N. Y.) 40: 875–898, https://doi.org/10.1122/1.550766.Search in Google Scholar

Wolff, F., Resch, J.A., Kaschta, J., and Münstedt, H. (2010). Comparison of viscous and elastic properties of polyolefin melts in shear and elongation. Rheol. Acta 49: 95–103, https://doi.org/10.1007/S00397-009-0396-2/FIGURES/15.Search in Google Scholar

Yamaguchi, M., Seemork, J., Siriprumpoonthum, M., Yokohara, T., Mohd Amran, B.M.A., and Phulkerd, P. (2022). Modification of rheological responses under elongational flow. Polym. Foam: 25–49, https://doi.org/10.1201/9781003166160-2.Search in Google Scholar

Yuan, Z., Chen, X., and Yu, D. (2021). Recent advances in elongational flow dominated polymer processing technologies. Polymers 13: 1792, https://doi.org/10.3390/POLYM13111792.Search in Google Scholar
Received: 2024-08-30
Accepted: 2025-02-15
Published Online: 2025-03-24
Published in Print: 2025-05-26

© 2025 Walter de Gruyter GmbH, Berlin/Boston

Articles in the same Issue

  1. Frontmatter
  2. Review Article
  3. Corrosion resistive conducting polymeric nanocomposite-based coatings on steel: a mechanistic insight
  4. Research Articles
  5. Effect of compatibilizer type on the properties of thermoplastic elastomers based on recycled polyethylene at high ground tire rubber content
  6. Analyzing the effects of solid fraction and heat treatment on the mechanical properties of 3D printed polymer lattices
  7. Effect of polyvinyl acetate on the properties of biodegradable thermoplastic starch/polyethylene glycol blends
  8. A color masterbatch assistance system for optimizing product color by masterbatch addition in injection molding of post-industrial recyclates
  9. Enhancing 3D printing with composite filaments incorporating electronic waste: a study on flexural and compression strength
  10. Development of enhanced co-continuous PVDF/PET nanocomposites via synergistic effects of graphite particle size, hybrid systems, and reduced graphene oxide
  11. Integration of nanographene and action of fiber sequences on functional behaviour of composite laminates
  12. Effect of chain branching on the rheological properties of HDPE/LLDPE and HDPE/LDPE blends under shear and elongational flows and evaluation of die swell and flow instabilities
  13. Effect of graphene nanoplatelets (GnPs) on low velocity impact properties of hybrid kevlar/basalt fiber reinforced epoxy based composites
  14. Sustainability in rotational molding: a study on recycling and the influence of additives
https://doi.org/10.1515/ipp-2024-0115
Keywords for this article
polyethylene; chain branching; polymer blends; shear and elongational flows; flow instabilities

Articles in the same Issue

  1. Frontmatter
  2. Review Article
  3. Corrosion resistive conducting polymeric nanocomposite-based coatings on steel: a mechanistic insight
  4. Research Articles
  5. Effect of compatibilizer type on the properties of thermoplastic elastomers based on recycled polyethylene at high ground tire rubber content
  6. Analyzing the effects of solid fraction and heat treatment on the mechanical properties of 3D printed polymer lattices
  7. Effect of polyvinyl acetate on the properties of biodegradable thermoplastic starch/polyethylene glycol blends
  8. A color masterbatch assistance system for optimizing product color by masterbatch addition in injection molding of post-industrial recyclates
  9. Enhancing 3D printing with composite filaments incorporating electronic waste: a study on flexural and compression strength
  10. Development of enhanced co-continuous PVDF/PET nanocomposites via synergistic effects of graphite particle size, hybrid systems, and reduced graphene oxide
  11. Integration of nanographene and action of fiber sequences on functional behaviour of composite laminates
  12. Effect of chain branching on the rheological properties of HDPE/LLDPE and HDPE/LDPE blends under shear and elongational flows and evaluation of die swell and flow instabilities
  13. Effect of graphene nanoplatelets (GnPs) on low velocity impact properties of hybrid kevlar/basalt fiber reinforced epoxy based composites
  14. Sustainability in rotational molding: a study on recycling and the influence of additives
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 11.10.2025 from https://www.degruyterbrill.com/document/doi/10.1515/ipp-2024-0115/html?lang=en
Scroll to top button