Article
Licensed
Unlicensed
Requires Authentication
Personal/Personelles
Published/Copyright:
February 16, 2022
Published Online: 2022-02-16
© 2003 Carl Hanser Verlag, München
You are currently not able to access this content.
You are currently not able to access this content.
Articles in the same Issue
- Frontmatter
- Articles/Aufsätze
- Bedeutung von Eigenspannungsabbau und mikrostrukturellen Veränderungen für die Lebensdauervorhersage schwingbeanspruchter Schweißverbindungen
- Factors affecting cyclic lifetime of EB-PVD thermal barrier coatings with various bond coats
- Depth-resolved X-ray residual stress analysis in PVD (Ti, Cr) N hard coatings
- Crystal orientation and residual stress in TiN film by synchrotron radiation
- Characterization of thermal and anodic oxide layers on β- and on near-β-titanium alloys for biomedical application
- Micromechanisms and modelling of crack initiation and growth in tool steels: role of primary carbides
- Fatigue crack nucleation at grain boundaries – experiment and simulation
- Fatigue and fracture-induced defect structures of metals investigated by positron microscopy
- Deformation and fracture of Nb/α-Al2O3 composites in compression and bending studied by optical methods
- Dislocation microstructures of single crystal ⟨001⟩ CMSX-4 specimens tensile tested at 700 and 1000°C
- Influence of mechanical surface treatments on the HCF performance of the Ni-superalloy Udimet 720 LI
- Precipitation of β-phase and twinning during deformation of Mg–Al alloy AZ91 at 150 °C after solution treatment
- Nanograin size, high-nitrogen austenitic stainless steels
- Der dynamische SD-Effekt und der Einfluss auf die Fließortkurve
- Einfluss der Umformgeschwindigkeit und -temperatur auf das Fließverhalten metallischer Werkstoffe
- Mean stress sensitivity of sintered iron and steel
- Thermozyklisches Kriechen einer kurzfaserverstärkten Aluminium-Kolbenlegierung
- Strength and ductility of thin Cu wires
- Modeling of deformation behavior of copper under equal channel angular pressing
- Reaktionssintern von AlMg–MgO zur Herstellung von Bauteilen auf Spinellbasis
- Determination of the local oxygen distribution in a commercial titanium alloy by 3-dimensional atom probe
- Phase diagram of the Al–Cu–Fe quasicrystal-forming alloy system
- Notifications/Mitteilungen
- Personal/Personelles
- Books/Bücher
- Conferences/Konferenzen
Articles in the same Issue
- Frontmatter
- Articles/Aufsätze
- Bedeutung von Eigenspannungsabbau und mikrostrukturellen Veränderungen für die Lebensdauervorhersage schwingbeanspruchter Schweißverbindungen
- Factors affecting cyclic lifetime of EB-PVD thermal barrier coatings with various bond coats
- Depth-resolved X-ray residual stress analysis in PVD (Ti, Cr) N hard coatings
- Crystal orientation and residual stress in TiN film by synchrotron radiation
- Characterization of thermal and anodic oxide layers on β- and on near-β-titanium alloys for biomedical application
- Micromechanisms and modelling of crack initiation and growth in tool steels: role of primary carbides
- Fatigue crack nucleation at grain boundaries – experiment and simulation
- Fatigue and fracture-induced defect structures of metals investigated by positron microscopy
- Deformation and fracture of Nb/α-Al2O3 composites in compression and bending studied by optical methods
- Dislocation microstructures of single crystal ⟨001⟩ CMSX-4 specimens tensile tested at 700 and 1000°C
- Influence of mechanical surface treatments on the HCF performance of the Ni-superalloy Udimet 720 LI
- Precipitation of β-phase and twinning during deformation of Mg–Al alloy AZ91 at 150 °C after solution treatment
- Nanograin size, high-nitrogen austenitic stainless steels
- Der dynamische SD-Effekt und der Einfluss auf die Fließortkurve
- Einfluss der Umformgeschwindigkeit und -temperatur auf das Fließverhalten metallischer Werkstoffe
- Mean stress sensitivity of sintered iron and steel
- Thermozyklisches Kriechen einer kurzfaserverstärkten Aluminium-Kolbenlegierung
- Strength and ductility of thin Cu wires
- Modeling of deformation behavior of copper under equal channel angular pressing
- Reaktionssintern von AlMg–MgO zur Herstellung von Bauteilen auf Spinellbasis
- Determination of the local oxygen distribution in a commercial titanium alloy by 3-dimensional atom probe
- Phase diagram of the Al–Cu–Fe quasicrystal-forming alloy system
- Notifications/Mitteilungen
- Personal/Personelles
- Books/Bücher
- Conferences/Konferenzen