Abstract
In this paper, a UWB MIMO (multi-input multi-output) antenna working from 3.3 GHz to 10 GHz with a single band notch at 4.5 GHz has been proposed. The antenna comprises of two circular microstrip patches of radius 6.4 mm with tapered microstrip feed line of input impedance 50 Ω connected to them. 1.6 mm thick FR4 substrate (εr = 4.4, tanδ = 0.02) of length and width 38 mm × 38 mm has been used. Partial ground consisting staircase, T-shaped slot, and defected H-shape slot have been utilized to enhance bandwidth and improve isolation. Additionally, C-shaped slot has been created on radiating element to produce a notch at 4.5 GHz. The design achieves a maximum gain of 5.8 dBi at 8.5 GHz and minimum gain of 0.5 dBi at 4.5 GHz. Isolation between the ports is more than 20 dB in the major portion of band of operation. It goes greater than 25 dB in the notch band. Envelope correlation coefficient (ECC) and diversity gain (DG) of 0.0006 and approx. 9.99 dB respectively has been obtained. Channel capacity loss of <−10 dB has been achieved. The proposed antenna is acceptable candidate for UWB MIMO applications.
-
Research ethics: This research has been carried out by keeping the originality of the work in the prime center. Authors of this paper are responsible for any conflict.
-
Author contributions: Mrs. Neha Dalakoti has done the simulation, fabrication and measurements presented in this paper under the guidance of Mrs. Priyanka Jain, Professor, Dept. Of ECE, DTU.
-
Competing interests: The authors state no conflict of interest.
-
Research funding: None declared.
-
Data availability: Not applicable.
References
[1] A. Kumar, A. Q. Ansari, B. K. Kanaujia, J. Kishor, and S. Kumar, “An ultra-compact two-port UWB-MIMO antenna with dual band-notched characteristics,” Int. J. Electron. Commun., vol. 114, no. 2, p. 152997, 2020. https://doi.org/10.1016/j.aeue.2019.152997.Search in Google Scholar
[2] A. Kumar, et al.., “Quad-band circularly polarized super-wideband MIMO antenna for wireless applications,” Int. J. RF Microw. Computer- Aided Eng., vol. 32, no. 6, p. 344, 2022. https://doi.org/10.1002/mmce.23129.Search in Google Scholar
[3] R. Chandel, A. K. Gautam, and K. Rambabu, “Tapered fed compact UWB MIMO-diversity antenna with dual band-notched characteristics,” IEEE Trans. Antenn. Propag., vol. 66, no. 4, pp. 1677–1684, 2018, https://doi.org/10.1109/tap.2018.2803134.Search in Google Scholar
[4] R. Sampath and K. T. Selvan, “Compact hybrid Sierpinski Koch fractal UWB MIMO antenna with pattern diversity,” Int. J. RF Microw. Computer- Aided Eng., vol. 30, no. 1, pp. 1–13, 2019. https://doi.org/10.1002/mmce.22017.Search in Google Scholar
[5] J. Mirza, S. Ghafoor, and A. Hussain, “A full-duplex ultra-wideband over multimode fiber link for internet of things based smart home applications,” Trans. Emerg. Telecommun. Technol., vol. 31, no. 10, pp. 1–11, 2020. https://doi.org/10.1002/ett.4050.Search in Google Scholar
[6] A. K. Singh, S. K. Mahto, and R. Sinha, “Compact super-wideband MIMO antenna with improved isolation for wireless communications,” Frequenz, vol. 75, nos. 9–10, pp. 407–417, 2021. https://doi.org/10.1515/freq-2020-0213.Search in Google Scholar
[7] A. K. Singh, S. K. Mahto, and R. Sinha, “A compact quad element MIMO antenna for LTE/5G (sub-6 GHz) applications,” Frequenz, vol. 77, nos. 3–4, pp. 1–11, 2022. https://doi.org/10.1515/freq-2022-0028.Search in Google Scholar
[8] Z. Xu, Q. Zhang, and L. Guo, “A compact 5G decoupling MIMO antenna based on split-ring resonators,” Int. J. Antenn. Propag., vol. 2019, no. 7, pp. 1–10, 2019. https://doi.org/10.1155/2019/3782528.Search in Google Scholar
[9] P. Garg and P. Jain, “Isolation improvement of MIMO antenna using a novel flower shaped metamaterial absorber at 5.5 GHz WiMAX band,” IEEE Trans. Circ. Syst. II: Express Briefs, vol. 67, no. 4, pp. 675–679, 2020. https://doi.org/10.1109/tcsii.2019.2925148.Search in Google Scholar
[10] A. A. Isaac, H. A-Rizzo, S. Yahya, A. A-Wahhamy, and S. Abushamleh, “Decoupling of two closely-spaced planar monopole antennas using two novel printed-circuit structures,” Microw. Opt. Technol. Lett., vol. 60, no. 12, pp. 2954–2963, 2018, https://doi.org/10.1002/mop.31405.Search in Google Scholar
[11] A. H. Radhi, R. Nilavalan, Y. Wang, H. S. Al-Raweshidy, A. A. Eltokhy, and N. A. Aziz, “Mutual coupling reduction with a wideband planar decoupling structure for UWB–MIMO antennas,” Int. J. Microw. Wireless Technol., vol. 10, no. 10, pp. 1143–1154, 2018, https://doi.org/10.1017/s1759078718001010.Search in Google Scholar
[12] J. Ghimire, K.-W. Choi, and D.-Y. Choi, “Bandwidth enhancement and mutual coupling reduction using a notch and a parasitic structure in a UWB-MIMO antenna,” Int. J. Antenn. Propag., vol. 2019, no. 5, pp. 1–9, 2019. https://doi.org/10.1155/2019/8945386.Search in Google Scholar
[13] X. Tang, Z. Yao, Y. Li, W. Zong, G. Liu, and F. Shan, “A high performance UWB MIMO antenna with defected ground structure and U-shape branches,” Int. J. RF Microw. Computer Aided Eng., vol. 31, no. 3, pp. 1–14, 2020. https://doi.org/10.1002/mmce.22270.Search in Google Scholar
[14] S. Mondal, K. Mandal, and P. P. Sarkar, “Design of MIMO antenna for ultra-wideband applications,” IETE J. Res., vol. 64, no. 4, pp. 497–502, 2018. https://doi.org/10.1080/03772063.2016.1176540.Search in Google Scholar
[15] N. Kumar and K. U. Kiran, “Meander-line electromagnetic bandgap structure for UWB MIMO antenna mutual coupling reduction in E-plane,” Int. J. Electron. Commun., vol. 127, no. 9, pp. 1–7, 2020, (AEÜ).10.1016/j.aeue.2020.153423Search in Google Scholar
[16] B. T. Ahmed and I. F. Rodriguez, “Compact high isolation UWB MIMO antennas,” Wireless Network., vol. 28, no. 10, pp. 1977–1999, 2022, https://doi.org/10.1007/s11276-022-02951-9.Search in Google Scholar
[17] A. K. Biswas and U. Chakraborty, “Reduced mutual coupling of compact MIMO antenna designed for WLAN and WiMAX applications,” Int. J. RF Microw. Computer Aided Eng., vol. 29, no. 2, pp. 1–10, 2018. https://doi.org/10.1002/mmce.21629.Search in Google Scholar
[18] A. Iqbal, O. A. Saraereh, A. W. Ahmad, and S. Bashir, “Mutual coupling reduction using F-shaped stubs in UWB-MIMO antenna,” IEEE Access, vol. 6, pp. 2755–2759, 2018, https://doi.org/10.1109/access.2017.2785232.Search in Google Scholar
[19] C. Sarkar and S. Ray, “Spur line implanted orthogonal microstrip-fed ultra-wideband MIMO linear taper slot antenna with WLAN band rejection,” Prog. Electromagn. Res. Lett., vol. 101, pp. 11–17, 2021, https://doi.org/10.2528/pierl21091102.Search in Google Scholar
[20] G. Saxena, P. Jain, and Y. K. Awasthi, “High diversity gain super-wideband single band-notch MIMO antenna for multiple wireless applications,” IET Microw. Antenn. Propag., vol. 14, no. 1, pp. 109–119, 2020, https://doi.org/10.1049/iet-map.2019.0450.Search in Google Scholar
[21] A. Bhattacharya, B. Roy, S. K. Chowdhury, and A. K. Bhattacharjee, “Computational and experimental analysis of a low-profile, isolation-enhanced, band-notch UWB-MIMO antenna,” J. Comput. Electron., vol. 18, no. 2, pp. 680–688, 2019, https://doi.org/10.1007/s10825-019-01309-3.Search in Google Scholar
[22] C. Du and G. Jin, “A compact CPW-fed band-notched UWB-MIMO flexible antenna for WBAN application,” J. Electromagn. Waves Appl., vol. 35, no. 8, pp. 1046–1058, 2021, https://doi.org/10.1080/09205071.2020.1868354.Search in Google Scholar
[23] G. Irene and A. Rajesh, “A dual-polarized UWB–MIMO antenna with IEEE 802.11ac band-notched characteristics using split-ring resonator,” J. Comput. Electron., vol. 17, no. 15, pp. 1090–1098, 2018, https://doi.org/10.1007/s10825-018-1213-x.Search in Google Scholar
[24] A. Kumar, A. Q. Ansari, B. K. Kanaujia, J. Kishor, and N. Tewari, “Design of triple-band MIMO antenna with one band-notched characteristic,” Prog. Electromagn. Res. C, vol. 86, pp. 41–53, 2018, https://doi.org/10.2528/pierc18051902.Search in Google Scholar
[25] V. R. Balaji, T. Addepalli, A. Desai, A. Nella, and T. K. Nguyen, “An inverted L-strip loaded ground with hollow semi-hexagonal four-element polarization diversity UWB-MIMO antenna,” Trans. Emerg. Telecommun. Technol., vol. 33, no. 1, pp. 1–13, 2022. https://doi.org/10.1002/ett.4381.Search in Google Scholar
[26] M. A. Abdelghany, M. Fathy Abo Sree, A. Desai, and A. A. Ibrahim, “4-Port octagonal shaped MIMO antenna with low mutual coupling for UWB applications,” Comput. Model. Eng. Sci., vol. 136, no. 2, pp. 1999–2015, 2023, https://doi.org/10.32604/cmes.2023.023643.Search in Google Scholar
[27] T. Addepalli, et al.., “8-Port semi-circular arc MIMO antenna with an inverted L-strip loaded connected ground for UWB applications,” Electronics, vol. 10, no. 12, pp. 1–19, 2021. https://doi.org/10.3390/electronics10121476.Search in Google Scholar
[28] A. Patel, et al.., “UWB CPW fed 4-port connected ground MIMO antenna for sub-millimeter-wave 5G applications,” Alexandria Eng. J., vol. 61, no. 9, pp. 6645–6658, 2022, https://doi.org/10.1016/j.aej.2021.12.015.Search in Google Scholar
[29] R. B. Sadineni and D. P. Gowda, “Design of penta-band notched UWB MIMO antenna for diverse wireless applications,” Prog. Electromagn. Res. M, vol. 107, pp. 35–49, 2022, https://doi.org/10.2528/pierm21112602.Search in Google Scholar
[30] R. K. Mistri, A. K. Singh, S. K. Mahto, and R. Sinha, “Quad element millimetre-wave MIMO antenna for 5G communication,” J. Electromagn. Waves Appl., vol. 37, no. 15, pp. 1258–1273, 2023, https://doi.org/10.1080/09205071.2023.2231934.Search in Google Scholar
[31] A. K. Singh, S. K. Mahto, and R. Sinha, “A miniaturized MIMO antenna for C, X, and Ku band applications,” Prog. Electromagn. Res., vol. 117, pp. 31–40, 2021, https://doi.org/10.2528/pierc21100202.Search in Google Scholar
[32] A. Desai, J. Kulkarni, M. M. Kamruzzaman, S. Hubalovsky, H.-T. Hsu, and A. A. Ibrahim, “Interconnected CPW fed flexible 4-port MIMO antenna for UWB, X, and Ku band applications,” IEEE Access, vol. 10, pp. 57641–57654, 2022. https://doi.org/10.1109/access.2022.3179005.Search in Google Scholar
[33] S. K. Mahto, A. K. Singh, R. Sinha, M. Alibakhshikenari, S. Khan, and G. Pau, “High isolated four element MIMO antenna for ISM/LTE/5G (Sub-6GHz) applications,” IEEE Access, vol. 11, pp. 82946–82959, 2023, https://doi.org/10.1109/access.2023.3301185.Search in Google Scholar
© 2024 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- Research Articles
- New indoor propagation model proposed for future B5G/6G rollout
- A miniaturized dual band pass frequency selective surface insensitive to oblique angles and polarizations of wave
- Design and equivalent circuit modelling of super compact ultrathin metamaterial absorber for microwave frequency Regime
- 3D printed circularly polarized implantable antenna with wideband impedance matching
- Design and investigation of cavity backed bowtie antenna with unidirectional radiation pattern using characteristic mode analysis
- A compact dual-element UWB-MIMO antenna with single band-notched characteristics
- Design and analysis of four leaf clover shaped MIMO antenna for Sub-6 GHz V2X applications
- The design and decoupling of TX/RX antenna with omnidirectional conical beam operating at V band
- Integration of two dual-port substrate integrated waveguide based MIMO antennas on a common substrate for 5G millimeter wave applications
- Antipodal vivaldi array MIMO antenna for 5G FR2 applications at 28 GHz with improved isolation
Articles in the same Issue
- Frontmatter
- Research Articles
- New indoor propagation model proposed for future B5G/6G rollout
- A miniaturized dual band pass frequency selective surface insensitive to oblique angles and polarizations of wave
- Design and equivalent circuit modelling of super compact ultrathin metamaterial absorber for microwave frequency Regime
- 3D printed circularly polarized implantable antenna with wideband impedance matching
- Design and investigation of cavity backed bowtie antenna with unidirectional radiation pattern using characteristic mode analysis
- A compact dual-element UWB-MIMO antenna with single band-notched characteristics
- Design and analysis of four leaf clover shaped MIMO antenna for Sub-6 GHz V2X applications
- The design and decoupling of TX/RX antenna with omnidirectional conical beam operating at V band
- Integration of two dual-port substrate integrated waveguide based MIMO antennas on a common substrate for 5G millimeter wave applications
- Antipodal vivaldi array MIMO antenna for 5G FR2 applications at 28 GHz with improved isolation