Home Physical Sciences Temperature drop sensor for monitoring kiln drying of lumber
Article
Licensed
Unlicensed Requires Authentication

Temperature drop sensor for monitoring kiln drying of lumber

  • Diego Miguel Elustondo , Luiz Oliveira and Peter Lister
Published/Copyright: February 13, 2009
Holzforschung
From the journal Volume 63 Issue 3

Abstract

The main objective of this study was to test a new sensor based on the temperature drop across the load (TDAL). The TDAL sensor was designed to determine the transition point between wet and dry wood without any specific information about the drying process. When additional information is available, the TDAL sensor can also be used to monitor drying rate and estimate the drying end-point. In this study, three potential applications of TDAL sensor for lumber drying were explored, namely, to monitor drying rate, to detect the transition point between wet and dry wood, and for determination of drying end-point after calibration. For the first application, it was demonstrated that the transition point between wet and dry wood coincides with the time at which the TDAL decreases with time at a constant logarithmic slope. For the second application, the TDAL sensor was calibrated with nine experimental drying runs, and the end-points determined with the calibrated TDAL sensor did not show a significant difference with the end-points determined by the in-kiln MC meter. Finally, the TDAL sensor was used to monitor drying rate during drying.


Corresponding author. FPInnovations – Forintek, 2665 East Mall, Vancouver, British Columbia, V6T 1W5, Canada Phone: +1-604-222-5662 Fax: +1-604-222-5690

Received: 2008-9-12
Accepted: 2009-1-12
Published Online: 2009-02-13
Published Online: 2009-02-15
Published in Print: 2009-05-01

©2009 by Walter de Gruyter Berlin New York

Articles in the same Issue

  1. Original Papers
  2. Laboratory and mill scale evaluation of biopulping of Eucalyptus grandis Hill ex Maiden with Phanerochaete chrysosporium RP-78 under non-aseptic conditions
  3. New kinetics and mechanisms of oxygen delignification observed in a continuous stirred tank reactor
  4. A study of anthraquinone-fortified green liquor pretreatment of loblolly pine chips
  5. Reactions of aromatic structures in brightness reversion of fully-bleached eucalyptus kraft pulps
  6. Effect of surface sizing on the surface chemistry of paper containing eucalyptus pulp
  7. Kraft lignin as feedstock for chemical products: The effects of membrane filtration
  8. Modification of lignin with laccases for the adsorption of anionic ferulic acid studied by quartz cristall microbalance with dissipation and AFM
  9. Modeling xylan solubilization during autohydrolysis of sugar maple wood meal: Reaction kinetics
  10. Grandidentatin isomer from bark of suwon poplar (Populus alba L.×Populus glandulosa Uyeki)
  11. Amination of pyrogallol nucleus of condensed tannins and related polyphenols by ammonia water treatment
  12. On the time-temperature equivalency in green wood: Characterisation of viscoelastic properties in longitudinal direction
  13. Temperature drop sensor for monitoring kiln drying of lumber
  14. Experimental and numerical determination of the hygroscopic warping of cross-laminated solid wood panels
  15. A single point NMR method for an instantaneous determination of the moisture content of wood
  16. Air permeability in longitudinal and radial directions of compression wood of Picea abies L. and tension wood of Fagus sylvatica L.
  17. A simulation of void variation in wood-strand composites during consolidation
  18. Sterols and lignin in Eucalyptus globulus Labill. wood: Spatial distribution and fungal removal as revealed by microscopy and chemical analyses
  19. Protection mechanisms of DMDHEU treated wood against white and brown rot fungi
  20. Meeting
  21. Meetings
Downloaded on 22.2.2026 from https://www.degruyterbrill.com/document/doi/10.1515/HF.2009.058/html
Scroll to top button