Band 63, Heft 6

Previous reports on the relationship between coil orientation and amplitude of motor evoked potential (MEP) in transcranial magnetic stimulation (TMS) did not consider the effect of electrode arrangement. Here we explore this open issue by investigating whether TMS coil orientation affects the amplitude distribution of MEPs recorded from the abductor pollicis brevis (APB) muscle with a bi-dimensional grid of 61 electrodes. Moreover, we test whether conventional mono- and bipolar montages provide representative MEPs compared to those from the grid of electrodes. Our results show that MEPs with the greatest amplitudes were elicited for 45° and 90° coil orientations, i.e. perpendicular to the central sulcus, for all electrode montages. Stimulation with the coil oriented at 135° and 315°, i.e. parallel to the central sulcus, elicited the smallest MEP amplitudes. Additionally, changes in coil orientation did not affect the spatial distribution of MEPs over the muscle extent. It has been shown that conventional electrodes with detection volume encompassing the APB belly may detect representative MEPs for optimal coil orientations. In turn, non-optimal orientations were identified only with the grid of electrodes. High-density electromyography may therefore provide new insights into the effect of coil orientation on MEPs from the APB muscle.

Noninvasive techniques are routinely used for assessment of tissue effects of lung ventilation. However, comprehensive studies of the response time of the methods are scarce. The aim of this study was to compare the response time of noninvasive methods for monitoring of gas exchange to sudden changes in the composition of the inspired gas. A prospective experimental study with 16 healthy volunteers was conducted. A ventilation circuit was designed that enabled a fast change in the composition of the inspiratory gas mixture while allowing spontaneous breathing. The volunteers inhaled a hypoxic mixture, then a hypercapnic mixture, a hyperoxic mixture and finally a 0.3% CO mixture. The parameters with the fastest response to the sudden change of O 2 in inhaled gas were peripheral capillary oxygen saturation ( Sp O 2 ) and regional tissue oxygenation ( rS O 2 ). Transcutaneous oxygen partial pressure ( tcp O 2 ) had almost the same time of reaction, but its time of relaxation was 2–3 times longer. End-tidal carbon dioxide ( Et CO 2 ) response time to change of CO 2 concentration in inhaled gas was less than half in comparison with transcutaneous carbon dioxide partial pressure ( tcp CO 2 ). All the examined parameters and devices reacted adequately to changes in gas concentration in the inspiratory gas mixture.

Radiostereometric analysis (RSA) is the gold standard for evaluating micromotions of orthopaedic implants. The method is applied for identifying novel design weaknesses in endoprostheses. Current research frequently assesses relatively short time periods. Short-term RSA studies have been widely used for predicting the long-term stability of many hip prosthetic designs, but only a few studies have focused on uncemented hip implants, especially for extended periods. The purpose of this study was to analyse the migration pattern of the Cerafit ® femoral stem within 10 years and to verify the predictive value of short-term RSA after 2 years for this uncemented femoral hip stem. Twenty-six patients were followed for 10 years. Ten years after implantation, a mean subsidence of 0.22 mm±0.56 mm, a mean internal rotation of 0.59°±1.67° and a mean maximum total point motion (MTPM) of 1.28 mm±0.54 mm were detected. The main migration took place in the first 6 weeks after surgery (subsidence of 0.36 mm±0.73 mm; internal rotation of 0.62°±1.49°, MTPM of 1.05 mm±0.68 mm). All the migration values measured were small. No late-onset migration was observed. This study suggests that the Cerafit ® implants are stable after 10 years. Thus, RSA could be the best tool to assess long-term implant behaviour.

Aim: To biomechanically compare a monocortical single frame external fixator (Orthofix UNYCO) with two bicortical fixator systems (dual frame: Stryker Hoffmann and single frame: Synthes LEF) with respect to system rigidity and stability under cyclic loading. Methods: The fixator systems were assessed for axial rigidity under loads which would occur clinically during fixator application and dynamic stability (cyclic fatigue) under loads which would occur in the first week postoperatively. Tests were performed on porcine tibiae (n>5 per group) with characteristic frame configurations. Loads were applied with an electrodynamic material testing machine and pin and frame deformations were continuously monitored with a marker based motion capturing system. Results: The bicortical single frame fixator revealed the largest rigidity (276±55) N/mm and was 20% (p=0.116) stiffer compared to the bicortical dual frame configuration and 39% (p=0.003) stiffer compared to the monocortical system. All systems survived 4000 cycles of loading, with the smallest vertical displacement (2.44±0.54 mm) observed for the bicortical dual frame system, followed by the monocortical single frame (3±0.55 mm, p=0.85) and bicortical single frame (3.25±0.96 mm, p=0.215). Conclusion: The monocortical fixation system performed comparably to the bicortical systems for its intended use as a temporary treatment before a definitive fracture osteosynthesis by plating or nailing.

There is a lack of noninvasive pulmonary function tests which can assess regional information of the lungs. Electrical impedance tomography (EIT) is a radiation-free, non-invasive real-time imaging that provides regional information of ventilation volume regarding the measurement of electrical impedance distribution. Forced oscillation technique (FOT) is a pulmonary function test which is based on the measurement of respiratory mechanical impedance over a frequency range. In this article, we introduce a new measurement approach by combining FOT and EIT, named the oscillatory electrical impedance tomography (oEIT). Our oEIT measurement system consists of a valve-based FOT device, an EIT device, pressure and flow sensors, and a computer fusing the data streams. Measurements were performed on five healthy volunteers at the frequencies 3, 4, 5, 6, 7, 8, 10, 15, and 20 Hz. The measurements suggest that the combination of FOT and EIT is a promising approach. High frequency responses are visible in the derivative of the global impedance index ΔZeit(t,fos).$\Delta {Z_{{\text{eit}}}}(t,{f_{{\text{os}}}}).$ The oEIT signals consist of three main components: forced oscillation, spontaneous breathing, and heart activity. The amplitude of the oscillation component decreases with increasing frequency. The band-pass filtered oEIT signal might be a new tool in regional lung function diagnostics, since local responses to high frequency perturbation could be distinguished between different lung regions.

Physical head phantoms allow the assessment of source reconstruction procedures in electroencephalography and electrical stimulation profiles during transcranial electric stimulation. Volume conduction in the head is strongly influenced by the skull, which represents the main conductivity barrier. Realistic modeling of its characteristics is thus important for phantom development. In the present study, we proposed plastic clay as a material for modeling the skull in phantoms. We analyzed five clay types varying in granularity and fractions of fire clay, each with firing temperatures from 550°C to 950°C. We investigated the conductivity of standardized clay samples when immersed in a 0.9% sodium chloride solution with time-resolved four-point impedance measurements. To test the reusability of the clay model, these measurements were repeated after cleaning the samples by rinsing in deionized water for 5 h. We found time-dependent impedance changes for approximately 5 min after immersion in the solution. Thereafter, the conductivities stabilized between 0.0716 S/m and 0.0224 S/m depending on clay type and firing temperatures. The reproducibility of the measurement results proved the effectiveness of the rinsing procedure. Clay provides formability, is permeable to ions, can be adjusted in conductivity value and is thus suitable for the skull modeling in phantoms.

Previous research investigated recumbent cycle power output (PO) from the perspective of knee and hip joint biomechanics. However, ankle-foot biomechanics and, in particular, the effect of ankle-foot orthosis (AFO)-constrained movements on cycle PO has not been widely explored. Therefore, the purpose of this study was to determine whether AFOs of a fixed position (FP) and in dorsi-plantarflexion (DPF)-, dorsiflexion (DF)- and plantarflexion (PF)-constrained movements might influence PO during voluntary recumbent cycling exercises. Twenty-five healthy individuals participated in this study. All underwent 1-min cycling at a fixed cadence for each of the AFOs. The peak and average PO of each condition were analyzed. The peak and average PO were 27.2±12.0 W (range 6–60) and 17.2±9.0 W (range 2–36), respectively, during voluntary cycling. There were no significant differences in the peak PO generated by the AFOs (p=0.083). There were also no significant differences in the average PO generated using different AFOs (p = 0.063). There were no significant differences in the changes of the hip and knee joint angles with different AFOs (p=0.974 and p=1.00, respectively). However, there was a significant difference in the changes of the ankle joint angle (p<0.00). The present study observed that AFO-constrained movements did not have an influence in altering PO during voluntary recumbent cycling in healthy individuals. This finding might serve as a reference for future rehabilitative cycling protocols.

The present work attempts to enhance the sensitivity of a folded beam microelectromechanical systems (MEMS) capacitive accelerometer by optimising the device geometry. The accelerometer is intended to serve as a microphone in the fully implantable hearing application which can be surgically implanted in the middle ear bone structure. For the efficient design of the accelerometer as a fully implantable biomedical device, the design parameters such as size, weight and resonant frequency have been considered. The geometrical parameters are varied to obtain the optimum sensitivity considering the design constraints and the stability of the structure. The optimised design is simulated and verified using COMSOL MULTIPHYSICS 4.2. The stability of the device is ensured using eigenfrequency analysis. Optimised results of the device geometry are presented and discussed. The accelerometer has a sensing area of 1 mm 2 and attains a nominal capacitance of 5.3 pF and an optimum sensitivity of 6.89 fF.

A novel biomechanical test bench has been developed for in-vitro evaluation of the knee joint. The test bench allows the kinematics of the knee joint to be studied in all six degrees of freedom. Flexion-extension knee movements are induced by quadriceps and hamstring muscle forces simulated by five pneumatic cylinders. The kinematics of the knee and the actively applied muscle forces are measured simultaneously. The aim of this study was to validate the sensitivity and reproducibility of this novel test bench. Four fresh frozen human knees were tested three times, each with seven flexion-extension cycles between 5° and 60°. After the native knees had been tested, the posterior cruciate ligament and then the lateral collateral ligament were dissected. The injured knees were tested in identical conditions [3×(7×5°–60°)] in order to evaluate whether the test bench is capable of detecting differences in knee kinematics between a native state and an injured one. With regard to reproducibility, the novel test bench showed almost perfect agreement for each specimen and for all states and flexion angles. In comparison with the native knees, the injured knees showed significant differences in knee kinematics. This validated novel test bench will make it possible to investigate various knee pathologies, as well as current and newly developed treatment options.

This paper follows up on a recent systematic review of test methods and parameters for biomechanical testing of bone plates and it is the first study that contains recommendations for standardized mechanical testing of bone plate-screw constructs for osteosynthesis. Following the testing philosophy of ASTM F382 and ISO 9585, we have developed standardized quasi-static and dynamic testing methods for straight linear and anatomically shaped plates, including locked type and conventional systems. The test specification comprises torsion and bending tests along the implant axis and therefore modifies and extends the methods proposed by ASTM F382. We present specific test setups in order to determine product-specific characteristics of the mechanical construct, consisting of the bone plate with corresponding screws (such as construct stiffness, yield strength, ultimate strength and fatigue properties) under the condition that it is rigidly fixed to “healthy bone”. We also address specific testing requirements that are important for the purpose of standardization, such as the positioning of the construct for testing or the number of screws in the diaphysis and metaphysis. Finally, we define the outcome parameters and associated failure criteria related to quasi-static and dynamic testing for comparative purposes. This paper does not intend to replace biomechanical testing of those devices under physiological loading conditions.

Pupillographic campimetry allows measuring the visual field objectively by analyzing the pupil response to perimetric stimuli. One of the drawbacks of this technique, similar to static perimetry, is the need of reliable fixation of the subject. By using stimulus sizes comparable to static perimetry and applying gaze tracking, we enable a retinotopic visual field examination regardless of fixation problems and with an increased stability and improved spatial resolution. Here, we present the results of applying the method in eight normal sighted subjects as well as in three patients suffering from diseases usually diagnosed by perimetry. The results in normal sighted subjects show a reduction in the amplitude of the pupil response with increasing eccentricity as expected. We also demonstrate that gaze-controlled campimetry is able to detect organic visual field defects objectively in a patient group and classify the visual field defects without an organic background. Moreover, we show that our method is able to evaluate the visual field sensitivity loss beyond classical perimetry in patients with late-stage retinitis pigmentosa. Thus, gaze-controlled pupil campimetry can be used in addition to classical perimetry, allowing for an objective monitoring of disease progression, rendering it as a biomarker for novel treatments.