Article
Licensed
Unlicensed
Requires Authentication
Investigation of the friction of flexographic and inkjet prints
-
Simona Grigaliuniene
Published/Copyright:
July 19, 2018
Published Online: 2018-07-19
Published in Print: 2015-08-01
© 2018 by Walter de Gruyter Berlin/Boston
You are currently not able to access this content.
You are currently not able to access this content.
Articles in the same Issue
- Tailor-made hemicellulose-based hydrogels reinforced with nanofibrillated cellulose for the removal of chromium ions from aqueous solutions
- Tailor-made hemicellulose-based hydrogels reinforced with nanofibrillated cellulose
- Influence of kaolin addition on the dynamics of oxygen mass transport in polyvinyl alcohol dispersion coatings
- Identification of process bottlenecks with global sensitivity analysis, an application to papermaking processes
- Evaluation of the influence of lipophilic extractive residues on dissolving pulp quality parameters by partial least squares method of chemometrics
- Vapor pressure and boiling point elevation of black liquor
- Refiner optimization and control Part III: Natural decoupling in TMP refining processes
- Refiner optimization and control Part IV: Long term follow up of control performance in TMP processes
- Amphoteric starch preflocculated talc filler for improving composite tensile index and filler bondability of paper
- Preparation of individualised lignocellulose microfibrils based on thermomechanical pulp and their effect on paper properties
- Improving the extensibility of paper: Sequential spray addition of gelatine and agar
- Two-stage versus one-stage refining of unbleached softwood kraft pulp – effects on tensile properties and compression strength
- Size and shape characterization of fines and fillers - a review
- Heat-Induced changes in oil and grease resistant hydroxypropylated-starch-based barrier coatings Sami-Seppo
- Characterizing unprinted paperboard surface for predicting optically induced halftone mottle
- Use of cellulose nanofibrils (CNF) in coating colors
- Investigation of the friction of flexographic and inkjet prints
- Ink and dirt behavior in repulping after artificial aging of coldset offset-printed newspapers at different temperatures
- Applying image analysis to measure flake content and flake size distribution in pulping of packaging board
- Soy flour detackification of stickies from paper recycling
Keywords for this article
Static friction coefficient;
Kinetic friction coefficient;
Flexographic prints;
Inkjet prints;
Surface roughness
Articles in the same Issue
- Tailor-made hemicellulose-based hydrogels reinforced with nanofibrillated cellulose for the removal of chromium ions from aqueous solutions
- Tailor-made hemicellulose-based hydrogels reinforced with nanofibrillated cellulose
- Influence of kaolin addition on the dynamics of oxygen mass transport in polyvinyl alcohol dispersion coatings
- Identification of process bottlenecks with global sensitivity analysis, an application to papermaking processes
- Evaluation of the influence of lipophilic extractive residues on dissolving pulp quality parameters by partial least squares method of chemometrics
- Vapor pressure and boiling point elevation of black liquor
- Refiner optimization and control Part III: Natural decoupling in TMP refining processes
- Refiner optimization and control Part IV: Long term follow up of control performance in TMP processes
- Amphoteric starch preflocculated talc filler for improving composite tensile index and filler bondability of paper
- Preparation of individualised lignocellulose microfibrils based on thermomechanical pulp and their effect on paper properties
- Improving the extensibility of paper: Sequential spray addition of gelatine and agar
- Two-stage versus one-stage refining of unbleached softwood kraft pulp – effects on tensile properties and compression strength
- Size and shape characterization of fines and fillers - a review
- Heat-Induced changes in oil and grease resistant hydroxypropylated-starch-based barrier coatings Sami-Seppo
- Characterizing unprinted paperboard surface for predicting optically induced halftone mottle
- Use of cellulose nanofibrils (CNF) in coating colors
- Investigation of the friction of flexographic and inkjet prints
- Ink and dirt behavior in repulping after artificial aging of coldset offset-printed newspapers at different temperatures
- Applying image analysis to measure flake content and flake size distribution in pulping of packaging board
- Soy flour detackification of stickies from paper recycling
