Startseite Engineering Analysis of Devolatilization of Various Additives in Intermeshing Co-rotating Twin Screw Extruders
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Engineering Analysis of Devolatilization of Various Additives in Intermeshing Co-rotating Twin Screw Extruders

  • J. Keum und J. L. White
Veröffentlicht/Copyright: 2. Mai 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
International Polymer Processing
Aus der Zeitschrift International Polymer Processing Band 19 Heft 2

Abstract

An experimental study of devolatilization of nonane, xylene and 1-hexanol from molten polyethylene in a modular co-rotating twin screw extruder is described. Various modular screw designs, as well as different feed rates, screw speeds, and barrel temperatures were used. It was found possible to correlate the extent of devolatilization in different modular screw designs with a mass transfer coefficient which depends on screw speed and LDPE feed rate. The mass transfer coefficient depended on the liquid being devolatilized, being highest with 1-hexanol and lowest with nonane. In addition, the values of the mass transfer coefficient were obtained through experiments on the twin-screw extrusion of PE with nonane, xylene and hexanol. Interpretations of these results are described.

∗ Mail address: J. L. White, Institute of Polymer Engineering, University of Akron, Akron, Ohio, USA 44325-0301 E-mail:

References

1 Latinen, G. A.: ACS Adv. Chem. Ser.34, p. 235 (1962).10.1021/ba-1962-0034.ch019Suche in Google Scholar

2 Coughlin, R. W., Canevari, G. P.: AIChE J.15, p. 560 (1969).10.1002/aic.690150416Suche in Google Scholar

3 Biesenberger, J. A., Kessidis, G.: Polym Eng. Sci.22, p. 832, (1982).10.1002/pen.760221308Suche in Google Scholar

4 Erdmenger, R.: Chem. Ing. Tech.34, p. 751 (1962).10.1002/cite.330341107Suche in Google Scholar

5 Todd, D. B.: SPE Antec Tech Papers, 32, p. 472 (1974).Suche in Google Scholar

6 Denson, C. D., in: Advances in Chemical Engineering, Wei, J. (Ed.) Academic Press, New York (1983).Suche in Google Scholar

7 Collins, G. P., Denson, C. D., Astarita, G.: AIChE J.31, p. 1288 (1985).10.1002/aic.690310807Suche in Google Scholar

8 Notorgiacom, V., Biesenberger, J.: SPE Antec Tech Papers46, p. 71 (1988).Suche in Google Scholar

9 Foster, R. W., Lindt, J. T.: Polym. Eng. Sci.29, p. 178 (1989).10.1002/pen.760290305Suche in Google Scholar

10 Foster, R. W., Lindt, J. T.: Polym. Eng. Sci.30, p. 424 (1990).10.1002/pen.760300707Suche in Google Scholar

11 Foster, R. W., Lindt, J. T.: Polym. Eng. Sci.30, p. 621 (1990).10.1002/pen.760301102Suche in Google Scholar

12 Biesenberger, J. A., Dey, S. K., Brizzolara, J.: Polym. Eng. Sci.30, p. 1493 (1990).10.1002/pen.760302302Suche in Google Scholar

13 Sakai, T., Hashimoto, N.: SPE Antec Tech Papers, 32, p. 360 (1986).Suche in Google Scholar

14 Maffetone, P. L., Denson, C. D.: J. Polym. Eng.13, p. 175 (1994).10.1515/POLYENG.1994.13.3.175Suche in Google Scholar

15 Wang, N. H., Sakai, T., Hashimoto, N.: Int. Polym. Process, 10, p. 296 (1995).Suche in Google Scholar

16 Yang, C., Smith, T. G., Bigio, D. I., Anolick, C.: SPE Antec Tech Papers. 55, p. 156 (1997).Suche in Google Scholar

17 Yang, C., Smith, T. G., Bigio, D. I., Anolick, C.: AIChE J.43, p. 1861 (1997).10.1002/aic.690430721Suche in Google Scholar

18 Higbe, R.: Trans. AlChE31, p. 365 (1935).10.1039/tf9353100365Suche in Google Scholar

19 Sherwood, T. K., Pigford, R. L., Wilke, C. E.: Mass Transfer. McGraw Hill, New York (1975).Suche in Google Scholar

20 Booy, M. L.: Polym. Eng. Sci.18, p. 973 (1978).10.1002/pen.760181212Suche in Google Scholar

21 Denson, C., Hwang, B. K.: Polym. Eng. Sci.20, p. 965 (1980).10.1002/pen.760201408Suche in Google Scholar

22 Bawiskar, S., White, J. L.: Int. Polym. Process.12, p. 331 (1997).10.3139/217.970331Suche in Google Scholar

23 White, J. L., Kim, B. J., Bawiskar, S., Keum, J. M.: Polymer-Plastics Technology and Engineering40, p. 385 (2001).10.1081/PPT-100002065Suche in Google Scholar

24 Werner, H.: Kunststoffe71, p. 18 (1981).10.1016/0011-2240(81)90040-7Suche in Google Scholar

Received: 2003-6-2
Accepted: 2003-12-29
Published Online: 2013-05-02
Published in Print: 2004-05-01

© 2004, Carl Hanser Verlag, Munich

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. DuPont, IG Farbenindustrie, ICI and Japanese PA Fiber Manufacturers Polyamides 66 and 6
  5. Screw Extrusion
  6. Modeling the Flow in the Metering Zone of Single Screw Extruders Using a Helical Geometry Model
  7. Engineering Analysis of Devolatilization of Various Additives in Intermeshing Co-rotating Twin Screw Extruders
  8. Die Extrusion
  9. Novel Extrusion Dies with Rotating Rollers for CO2-Plastic Foam Production
  10. Experimental Investigation of the Development of Interfacial Instabilities in Two Layer Coextrusion Dies
  11. Detachment of the Polymer Melt from the Roll Surface: Calendering Analysis and Data from a Shear Roll Extruder
  12. Reactive Extrusion
  13. Reactive Extrusion of SAN/EPDM Blends
  14. Film
  15. Easy Tear Film of Biaxially Oriented PA 6/MXD 6 Blend by Double Bubble Tubular Film Process
  16. Deformation Behavior, Processability and Physical Properties for Biaxially Oriented Film of LLDPE
  17. Stretchability and Properties of LLDPE Blends for Biaxially Oriented Film
  18. Stretchability and Properties of Various LLDPE for Biaxially Oriented Film
  19. Molding
  20. Microinjection Molding with LIGA-Like Process
  21. Thermoforming
  22. On the Use of the Heating Stage to Control the Thickness Distribution in Thermoformed Parts
  23. PPS News
  24. PPS News
https://doi.org/10.3139/217.1815

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. DuPont, IG Farbenindustrie, ICI and Japanese PA Fiber Manufacturers Polyamides 66 and 6
  5. Screw Extrusion
  6. Modeling the Flow in the Metering Zone of Single Screw Extruders Using a Helical Geometry Model
  7. Engineering Analysis of Devolatilization of Various Additives in Intermeshing Co-rotating Twin Screw Extruders
  8. Die Extrusion
  9. Novel Extrusion Dies with Rotating Rollers for CO2-Plastic Foam Production
  10. Experimental Investigation of the Development of Interfacial Instabilities in Two Layer Coextrusion Dies
  11. Detachment of the Polymer Melt from the Roll Surface: Calendering Analysis and Data from a Shear Roll Extruder
  12. Reactive Extrusion
  13. Reactive Extrusion of SAN/EPDM Blends
  14. Film
  15. Easy Tear Film of Biaxially Oriented PA 6/MXD 6 Blend by Double Bubble Tubular Film Process
  16. Deformation Behavior, Processability and Physical Properties for Biaxially Oriented Film of LLDPE
  17. Stretchability and Properties of LLDPE Blends for Biaxially Oriented Film
  18. Stretchability and Properties of Various LLDPE for Biaxially Oriented Film
  19. Molding
  20. Microinjection Molding with LIGA-Like Process
  21. Thermoforming
  22. On the Use of the Heating Stage to Control the Thickness Distribution in Thermoformed Parts
  23. PPS News
  24. PPS News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 2.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/217.1815/html?lang=de
Button zum nach oben scrollen