Startseite Effect of manganese on the microstructure and mechanical properties of magnesium alloys
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Effect of manganese on the microstructure and mechanical properties of magnesium alloys

  • Zhengwen Yu , Aitao Tang , Caiyu Li , Jianguo Liu und Fusheng Pan
Veröffentlicht/Copyright: 23. Oktober 2019
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 110 Heft 11

Abstract

The influence of Mn on the microstructure and mechanical properties of as-cast and as-solution Mg–Mn alloys was investigated in the present work. X-ray diffraction patterns revealed that the dominant phases of the experimental alloys were the α-Mg matrix and Mn precipitates. The average grain sizes of the as-cast Mg–Mn alloys decreased monotonically with increasing Mn content, although Mn addition showed a negative grain refinement effect on the as-cast Mg alloys. Increasing the Mn content enhanced the tensile yield strength of the as-cast alloys from 17.6 to 35.1 MPa. The improved mechanical properties are mainly attributed to precipitation hardening; a large number of Mn precipitates were located within the matrix and along the grain boundaries. Meanwhile, the lower tensile strength and Vickers hardness of the as-solution alloys is explained by the coarsened microstructure and poor solid-solution strengthening behaviour.

Keywords: Mechanical properties; Mg–Mn alloys; Microstructure; Vickers hardness
∗Correspondence address, Professor Aitao Tang, College of Materials Science and Engineering, Chongqing University, Shazhengjie, Chongqing 400044, People's Republic of China, Tel.: +86-23-65106121, Fax: +86-23-65106121, E-mail: , Web: http://ccmg.cqu.edu.cn/info/1019/1124.htm
∗∗ Professor Jianguo Liu, Key Laboratory of Oral Disease Research, School of Stomatology, Zunyi Medical University, West Xuefu Road, Zunyi 563003, People's Republic of China, Tel: +86-851-28643466, Fax: +86-851-28643466, E-mail: , Web: http://www.zmu.edu.cn/info/1005/12507.htm

References

[1] J.Zhang, S.Liu, R.Wu, L.Hou, M.Zhang: J. Magnesium Alloys6 (2018) 277. 10.1016/j.jma.2018.08.001Suche in Google Scholar

[2] X.Gu, Y.Zheng, Y.Cheng, S.Zhong, T.Xi: Biomater.30 (2009) 484. 19000636 10.1016/j.biomaterials.2008.10.021Suche in Google Scholar PubMed

[3] R.Radha, D.Sreekanth: J. Magnesium Alloys5 (2017) 286. 10.1016/j.jma.2017.08.003Suche in Google Scholar

[4] S.Agarwal, J.Curtin, B.Duffy, S.Jaiswal: Mater. Sci. Eng.C 68 (2016) 948. 27524097 10.1016/j.msec.2016.06.020Suche in Google Scholar PubMed

[5] S.You, Y.Huang, K.U.Kainer, N.Hor: J. Magnesium Alloys5 (2017) 239. 10.1016/j.jma.2017.09.001Suche in Google Scholar

[6] Z.Yu, M.Hu, A.Tang, M.Wu, J.He, Z.Gao, F.Wang, C.Li, B.Chen, J.Liu: Mater. Sci. Technol.33 (2017) 2086. 10.1080/02670836.2017.1345824Suche in Google Scholar

[7] Z.Yu, A.Tang, J.He, Z.Gao, J.She, J.Liu, F.Pan: Mater. Charact.136 (2018) 310. 10.1016/j.matchar.2017.12.029Suche in Google Scholar

[8] D.Bian, J.Jiang, W.Zhou, N.Li, Y.Zheng, S.Leeflang, J.Zhou: Mater. Lett.211 (2018) 261. 10.1016/j.matlet.2017.09.092Suche in Google Scholar

[9] D.Xia, Y.Liu, S.Wang, R.Zeng, Y.Liu, Y.Zheng, Y.Zhou: Sci. China Mater.62 (2019) 256. 10.1007/s40843-018-9293-8Suche in Google Scholar

[10] Z.Yu, A.Tang, Q.Wang, Z.Gao, J.He, J.She, K.Song, F.Pan: Mater. Sci. Eng.A 648 (2015) 202. 10.1016/j.msea.2015.09.065Suche in Google Scholar

[11] D.Gandel, M.Easton, M.Gibson, N.Birbilis: Corros.69 (2013) 666. 10.5006/0827Suche in Google Scholar

[12] S.Arthanari, R.Nallaiyan, S.Seon: J. Magnesium Alloys5 (2017) 277. 10.1016/j.jma.2017.08.001Suche in Google Scholar

[13] B.Mingo, R.Arrabal, M.Mohedano, C.L.Mendis, R. delOlmo, E.Matykina, N.Hort, M.C.Merino, A.Pardo: Mater. Des.130 (2017) 48. 10.1016/j.matdes.2017.05.048Suche in Google Scholar

[14] D.Gandel, M.Easton, M.Gibson, N.Birbilis: Corros.69 (2013) 744. 10.5006/0828Suche in Google Scholar

[15] J.Wang, R.Lu, D.Qin, X.Huang, F.Pan: Mater. Sci. Eng.A 560 (2013) 667. 10.1016/j.msea.2012.10.010Suche in Google Scholar

[16] M.Liu, G.Song: Corros. Sci.77 (2013) 143. 10.1016/j.corsci.2013.07.037Suche in Google Scholar

[17] Y.Lee, A.Dahle, D.StJohn: Metall. Mater. Trans.A 31 (2000) 2895. 10.1007/BF02830349Suche in Google Scholar

[18] Z.Yu, A.Tang, L.Zhang, F.Pan, Mater. Sci. Technol.30 (2014) 1441. 10.1179/1743284714Y.0000000528Suche in Google Scholar

[19] P.Cao, M.Qian, D.StJohn: Scr. Mater.54 (2006) 1853. 10.1016/j.scriptamat.2006.02.020Suche in Google Scholar

[20] O.Lunder, T.Aune, K.Nisancioglu: Corros.43 (1987) 291. 10.5006/1.3583151Suche in Google Scholar

[21] Y.Tamura, J.Yagi, T.Haitani, T.Motegi, N.Kono, H.Tamehiro, H.Saito: Mater. Trans.44 (2003) 552. 10.2320/matertrans.44.552Suche in Google Scholar

[22] F. VonBuch, J.Lietzau, B.Mordike, A.Pisch, R.Schmid-Fetzer: Mater. Sci. Eng.A 263 (1999) 1. 10.1016/S0921-5093(98)01040-5Suche in Google Scholar

[23] J.Bohlen, S.Yi, D.Letzig, K.Kainer: Mater. Sci. Eng.A 527 (2010) 7092. 10.1016/j.msea.2010.07.081Suche in Google Scholar

[24] J.Nie: Metall. Mater. Trans.A 43 (2012) 3891. 10.1007/s11661-012-1217-2Suche in Google Scholar

[25] D.Stratford, L.Beckley: Met. Sci. J.6 (1972) 83. 10.1179/030634572790446127Suche in Google Scholar

[26] P.Skjerpe, C.Simensen: Met. Sci.17 (1983) 403. 10.1179/030634583790420682Suche in Google Scholar

[27] M.Zhang, P.Kelly: Acta Mater.53 (2005) 1085. 10.1016/j.actamat.2004.11.005Suche in Google Scholar

[28] A.Luo, A.Sachdev: Metall. Mater. Trans.A 38 (2007) 1184. 10.1007/s11661-007-9129-2Suche in Google Scholar

[29] L.Tong, M.Zheng, S.Xu, S.Kamado, Y.Du, X.Hu, K.Wu, W.Gan, H.Brokmeier, G.Wang, X.Lv: Mater. Sci. Eng.A 528 (2011) 3741. 10.1016/j.msea.2011.01.037Suche in Google Scholar

[30] R.Wang, A.Eliezer, E.Gutman: Mater. Sci. Eng.A 355 (2003) 201. 10.1016/S0921-5093(03)00065-0Suche in Google Scholar

[31] D.Fang, N.Ma, K.Cai, X.Cai, Y.Chai, Q.Peng: Mater. Des.54 (2014) 72. 10.1016/j.matdes.2013.08.028Suche in Google Scholar

[32] H.Borkar, M.Hoseini, M.Pekguleryuz: Mater. Sci. Eng.A 549 (2012) 168. 10.1016/j.msea.2012.04.029Suche in Google Scholar

[33] M.Masoumi, M.Hoseini, M.Pekguleryuz: Mater. Sci. Eng.A 528 (2011) 3122. 10.1016/j.msea.2010.12.096Suche in Google Scholar

[34] M.Huppmann, S.Gall, S.Müller, W.Reimers: Mater. Sci. Eng.A 528 (2010) 342. 10.1016/j.msea.2010.09.025Suche in Google Scholar

[35] J.Gröbner, R.Schmid-Fetzer: J. Alloys Compd.320 (2001) 296. 10.1016/S0925-8388(00)01480-8Suche in Google Scholar

[36] Z.Shi, W.Zhang: Acta Metall. Sinica47 (2011) 41. 10.3724/SP.J.1037.2010.00323Suche in Google Scholar

[37] L.Gao, R.Chen, E.Han: J. Alloys Compd.472 (2009) 234. 10.1016/j.jallcom.2008.04.049Suche in Google Scholar

[38] L.Gao, R.Chen, E.Han: J. Alloys Compd.481 (2009) 379. 10.1016/j.jallcom.2009.02.131Suche in Google Scholar

[39] A.Blake, C.Cáceres: Mater. Sci. Eng.A 483–484 (2008) 161. 10.1016/j.msea.2006.10.205Suche in Google Scholar

[40] B.Shi, R.Chen, W.Ke: J. Alloys Compd.509 (2011) 3357. 10.1016/j.jallcom.2010.12.065Suche in Google Scholar

[41] J.Nie, Y.Zhu, J.Liu, X.Fang: Science340 (2013) 957. 23704567 10.1126/science.1229369Suche in Google Scholar PubMed

[42] H.Okamoto: J. Phase Equilib. Diff.33 (2012) 496. 10.1007/s11669-008-9272-5Suche in Google Scholar

[43] J.Gröbner, D.Mirkovic, M.Ohno, R.Schmid-Fetzer: J. Phase Equilib. Diff.26 (2005) 234. 10.1007/s11669-005-0110-8Suche in Google Scholar

[44] A.Nayeb-Hashemi, J.Clark: Bull. Alloy Phase Diag.6 (1985) 160. 10.1007/BF02869234Suche in Google Scholar

[45] J.Zhang, C.Fang, F.Yuan, C.Liu: Mater. Des.32 (2011) 1783. 10.1016/j.matdes.2010.12.048Suche in Google Scholar

[46] C.Caceres, D.Rovera: J. Light Met.1 (2001) 151. 10.1016/S1471-5317(01)00008-6Suche in Google Scholar

[47] Y.Xu, F.Gensch, Z.Ren, K.Kainer, N.Hort: Prog. Nat. Sci. – Mater.28 (2018) 724. 10.1016/j.pnsc.2018.10.002Suche in Google Scholar

[48] R.Fleisgher: Acta Metall.9 (1961) 996. 10.1016/0001-6160(61)90242-5Suche in Google Scholar

[49] R.Labusch: Phys. Status SolidiB 41 (1970) 659. 10.1002/pssb.19700410221Suche in Google Scholar

Received: 2019-01-23
Accepted: 2019-06-28
Published Online: 2019-10-23
Published in Print: 2019-11-12

© 2019, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Note from the Editor-in-Chief
  5. Original Contributions
  6. The softening factor cb of commercial titanium alloy wires
  7. A comparative assessment of cyclic deformation behavior of SA333 Gr-6 steel at ambient and elevated temperatures
  8. Effects of Ni and Al on the Cu-precipitation in ferritic Fe–Cu–M (M = Ni or Al) alloy
  9. Effect of manganese on the microstructure and mechanical properties of magnesium alloys
  10. Effect of heat treatment and extrusion on wear properties of AZ91-Pr alloy
  11. Effect of anodization treatment on the mechanical properties and fatigue behavior of AA2017-T4 aluminum alloy Al–Cu–Mg1
  12. Microstructural and tribological characterization of molybdenum–molybdenum carbide structures produced by spark plasma sintering
  13. Investigation of indentation and dry sliding wear behaviour of Al-12.6 wt.% Si-10 wt.% TiB2 composites produced by sequential milling and pressureless sintering
  14. Enthalpies of mixing in ternary Ce–Cu–Sb liquid alloys
  15. Effect of in-situ formation of AlP on solidification of hypereutectic Al–Si alloy
  16. Complex-shaped high speed steel with high mechanical performance fabricated by gelcasting sintering
  17. Internal electromagnetic stirring method for preparing a large-sized aluminum alloy billet
  18. DGM News
  19. DGM News
https://doi.org/10.3139/146.111843
Schlagwörter für diesen Artikel
Mechanical properties; Mg–Mn alloys; Microstructure; Vickers hardness

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Note from the Editor-in-Chief
  5. Original Contributions
  6. The softening factor cb of commercial titanium alloy wires
  7. A comparative assessment of cyclic deformation behavior of SA333 Gr-6 steel at ambient and elevated temperatures
  8. Effects of Ni and Al on the Cu-precipitation in ferritic Fe–Cu–M (M = Ni or Al) alloy
  9. Effect of manganese on the microstructure and mechanical properties of magnesium alloys
  10. Effect of heat treatment and extrusion on wear properties of AZ91-Pr alloy
  11. Effect of anodization treatment on the mechanical properties and fatigue behavior of AA2017-T4 aluminum alloy Al–Cu–Mg1
  12. Microstructural and tribological characterization of molybdenum–molybdenum carbide structures produced by spark plasma sintering
  13. Investigation of indentation and dry sliding wear behaviour of Al-12.6 wt.% Si-10 wt.% TiB2 composites produced by sequential milling and pressureless sintering
  14. Enthalpies of mixing in ternary Ce–Cu–Sb liquid alloys
  15. Effect of in-situ formation of AlP on solidification of hypereutectic Al–Si alloy
  16. Complex-shaped high speed steel with high mechanical performance fabricated by gelcasting sintering
  17. Internal electromagnetic stirring method for preparing a large-sized aluminum alloy billet
  18. DGM News
  19. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 16.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.111843/pdf
Button zum nach oben scrollen