Home W–Cu composites subjected to heavy hot deformation
Article
Licensed
Unlicensed Requires Authentication

W–Cu composites subjected to heavy hot deformation

  • Yang Yu , Xiaoqiang Xu and Wencong Zhang
Published/Copyright: March 31, 2017
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 108 Issue 4

Abstract

The effect of plastic deformation on the properties and microstructure of W–Cu composites produced by multi-pass hot extrusion with steel cup was investigated. W–Cu composites were sintered at 1 100 °C and then the sintered billets were firstly extruded at 900 °C with different extrusion ratios. The second hot extrusion was performed at 900 °C. The plastic deformation of copper phase plays a dominant part during the whole extrusion process. The microstructural evolution of W phase during the whole processing of heavy hot deformation can be divided into different stages. Experimental results indicate that the W agglomeration will be broken into fine particles effectively when the accumulated plastic deformation amounts to 97.6 % after the second extrusion.

Keywords: W–Cu composite; Hot extrusion with steel cup; Microstructural evolution; Electrical conductivity; Hardness
*Correspondence address, Professor Yang Yu, School of Materials Science and Engineering, Harbin Institute of Technology-Weihai, No. 2, West Wenhua Road, Weihai 264209, P.R. China, Tel.: +86 135-6317-1916, E-mail:

References

[1] J.L.Johnson, R.M.German: Int. J. Powder Metall.30 (1994) 205. 10.1016/0026-0657(95)92625-9Search in Google Scholar

[2] Z.J.Zhou, J.Du, S.X.Song, Z.H.Zhong, C.C.Ge: J. Alloys Compd.428 (2007) 146. 10.1016/j.jallcom.2006.03.073Search in Google Scholar

[3] S.B.Li, J.X.Xie: Compos. Sci. Technol.66 (2006) 2329. 10.1016/j.compscitech.2005.11.034Search in Google Scholar

[4] S.S.Ryu, Y.D.Kim, I.H.Moon: J. Alloys Compd.335 (2002) 233. 10.1016/S0925-8388(01)01805-9Search in Google Scholar

[5] J.L.Johnson, J.J.Brezovsky, R.M.German: Metall. Mater. Trans. A36 (2005) 2807. 10.1007/s11661-005-0277-ySearch in Google Scholar

[6] M.Ardestani, H.R.Rezaie, H.Arabi, H.Razavizadeh: Int. J. Refract. Met. Hard Mater.27 (2009) 862. 10.1016/j.ijrmhm.2009.04.004Search in Google Scholar

[7] K.Zangeneh-Madar, M.Amirjan, N.Parvin: Surf. Coat. Technol.203 (2009) 2333. 10.1016/j.surfcoat.2009.02.055Search in Google Scholar

[8] M.Amirjan, K.Zangeneh-Madar, N.Parvin: Int. J. Refract. Met. Hard Mater.27 (2009) 729. 10.1016/j.ijrmhm.2008.12.008Search in Google Scholar

[9] A.G.Hamidi, H.Arabi, S.Rastegari: Int. J. Refract. Met. Hard Mater.29 (2011) 538. 10.1016/j.ijrmhm.2011.03.009Search in Google Scholar

[10] P.A.Chen, G.Q.Luo, Q.Shen, M.J.Li, L.M.Zhang: Mater. Des.46 (2013) 101. 10.1016/j.matdes.2012.09.034Search in Google Scholar

[11] S.D.Luo, J.H.Yi, Y.L.Guo, Y.D.Peng, L.Y.Li, J.M.Ran: J. Alloys Compd.473 (2009) L5. 10.1016/j.jallcom.2008.05.038Search in Google Scholar

[12] R.Liu, T.Hao, K.Wang, T.Zhang, X.P.Wang, C.S.Liu, Q.F.Fang: J. Nucl. Mater.431 (2012)196. 10.1016/j.jnucmat.2011.11.013Search in Google Scholar

[13] Y.Zhou, Q.X.Sun, R.Liu, X.P.Wang, C.S.Liu, Q.F.Fang: J. Alloys Compd.547 (2013) 18. 10.1016/j.jallcom.2012.08.143Search in Google Scholar

[14] L.Xu, M.Yan, Y.Xia, J.H.Peng, W.Li, L.B.Zhang, C.H.Liu, G.Chen, Y.Li: J. Alloys Compd.592 (2014) 202. 10.1016/j.jallcom.2013.12.202Search in Google Scholar

[15] D.D.Gu, Y.F.Shen: Mater. Sci. Eng. A489 (2008) 169. 10.1016/j.msea.2007.12.008Search in Google Scholar

[16] Z.J.Zhou, Y.S.Kwon: J. Mater. Process. Technol.168 (2005) 107. 10.1016/j.jmatprotec.2004.11.008Search in Google Scholar

[17] I.Sabirov, R.Pippan: Mater. Charact.58 (2007) 848. 10.1016/j.matchar.2006.08.001Search in Google Scholar

[18] I.Sabirov, R.Pippan: Scr. Mater.52 (2005)1293. 10.1016/j.scriptamat.2005.02.017Search in Google Scholar

[19] D.R.Li, Z.Y.Liu, Y.Yu, E.D.Wang: J. Alloys Compd.462 (2008) 94. 10.1016/j.jallcom.2007.08.042Search in Google Scholar

[20] X.L.Xie, Q.Lin, D.Liu, Z.Y.Liu, E. D.Wang: Mater. Sci. Eng. A.578 (2013) 187. 10.1016/j.msea.2013.04.082Search in Google Scholar

[21] Y.Yu, W.C.Zhang, H.Yu: Adv. Powder Technol.26 (2015) 1047. 10.1016/j.apt.2015.04.012Search in Google Scholar

[22] D.R.Li, Z.Y.Liu, Y.Yu, E.DWang: Int. J. Refract. Met. Hard Mater.26 (2008) 286. 10.1016/j.ijrmhm.2007.06.004Search in Google Scholar

[23] D.R.Li, Z.Y.Liu, Y.Yu, E.D.Wang: Mater. Sci. Eng. A499 (2009) 118. 10.1016/j.msea.2007.11.125.wSearch in Google Scholar

[24] W.S.Wang, K.S.Hwang: Metall. Mater. Trans. A29 (1998) 1509. 10.1007/s11661-998-0366-9Search in Google Scholar

Received: 2016-11-11
Accepted: 2017-01-17
Published Online: 2017-03-31
Published in Print: 2017-04-13

© 2017, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Formation of intermetallic compounds and their effect on mechanical properties of aluminum–titanium alloy films
  5. Microstructure and properties of hot extruded Mg-3Zn-Y-xCu (x = 0, 1, 3, 5) alloys
  6. Effects of rare-earth element addition and heat treatment on the microstructures and mechanical properties of Al-25 % Si alloy
  7. Effects of silicon on characteristics of dynamic strain aging in a near-α titanium alloy
  8. Influence of heat treatment on the structure, hardness and strength of ZnAl40Cu3 alloy
  9. W–Cu composites subjected to heavy hot deformation
  10. Electrochemical performance of CuBi2O4 nanoparticles synthesized via a polyacrylamide gel route
  11. Mechanical properties of nano-SiO2 reinforced 3D glass fiber/epoxy composites
  12. Reinforcement effect and synergy of carbon nanofillers with different dimensions in high density polyethylene based nanocomposites
  13. Short Communications
  14. A general method towards transition metal monoboride nanopowders
  15. DGM News
  16. DGM News
https://doi.org/10.3139/146.111481
Keywords for this article
W–Cu composite; Hot extrusion with steel cup; Microstructural evolution; Electrical conductivity; Hardness

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Formation of intermetallic compounds and their effect on mechanical properties of aluminum–titanium alloy films
  5. Microstructure and properties of hot extruded Mg-3Zn-Y-xCu (x = 0, 1, 3, 5) alloys
  6. Effects of rare-earth element addition and heat treatment on the microstructures and mechanical properties of Al-25 % Si alloy
  7. Effects of silicon on characteristics of dynamic strain aging in a near-α titanium alloy
  8. Influence of heat treatment on the structure, hardness and strength of ZnAl40Cu3 alloy
  9. W–Cu composites subjected to heavy hot deformation
  10. Electrochemical performance of CuBi2O4 nanoparticles synthesized via a polyacrylamide gel route
  11. Mechanical properties of nano-SiO2 reinforced 3D glass fiber/epoxy composites
  12. Reinforcement effect and synergy of carbon nanofillers with different dimensions in high density polyethylene based nanocomposites
  13. Short Communications
  14. A general method towards transition metal monoboride nanopowders
  15. DGM News
  16. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 16.11.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.111481/pdf
Scroll to top button