Startseite Microstructure, texture, grain boundary characteristics and mechanical properties of a cold rolled and annealed ferrite–bainite dual phase steel
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Microstructure, texture, grain boundary characteristics and mechanical properties of a cold rolled and annealed ferrite–bainite dual phase steel

  • Chiradeep Ghosh , Arunansu Haldar , Pampa Ghosh und Ranjit Kumar Ray
Veröffentlicht/Copyright: 31. Mai 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 101 Heft 10

Abstract

The microstructural, textural evolution and changes in grain boundary character distribution during annealing of a prior cold worked (30 %, 50 % and 80 %) ferrite–bainite dual phase steel have been studied and correlated with mechanical properties. It has been shown that submicron sized subgrains can be obtained by selecting the appropriate amount of cold rolling and annealing cycle. Increasing the annealing temperature in all the materials produces the expected results, namely decrease in strength with a simultaneous increase in ductility. Although reasonably sharp γ-fibres were obtained in 80 % cold rolled and its 500 °C annealed counterpart, the very low values (< 1.0) make the steel unsuitable for the purpose of deep drawing. It is envisaged that grain boundary engineering may lead to better strength–ductility combinations in this steel for an enhanced range of applications.

Keywords: Microstructure; Texture; Grain boundary character distribution; Cold rolling; Mechanical properties
* Correspondence address, Chiradeep Ghosh PhD Scholar, McGill University, Materials Engineering, M. H. Wong Building, 3610 University Street, Montreal, Quebec, Canada H3A 2B2 E-mail:

References

[1] A.Murugaiyan, A.Saha Podder, A.Pandit, S.Chandra, D.Bhattacharjee, R.K.Ray: ISIJ Int.46 (2006) 1489. 10.2355/isijinternational.46.1489Suche in Google Scholar

[2] A.P.Coldren, G.Tither: JOM30 (1978) 6.Suche in Google Scholar

[3] M.Rashid: SAE Paper 770164 presented at Int. Automotive Engineering Cong. and Exposition, Detroit, Michigan, (1977).Suche in Google Scholar

[4] S.Hayami, T.Furukawa: Proc. Microalloying Conf., Vanitec, London, (1975) 78.Suche in Google Scholar

[5] A.Saha Podder, D.Bhattacharjee, R.K.Ray: ISIJ Int.47 (2007) 1058. 10.2355/isijinternational.47.1058Suche in Google Scholar

[6] M.Sudo, S.Hashimoto, T.Hosoda, Z.Shibata, K.Hirata: 1983 R and D: Research and Development Kobe Steel Engineering Reports33 (4) 49.Suche in Google Scholar

[7] T.Waterschoot, B.C.De Cooman, D.Vanderschueren: Ironmaking and Steelmaking.28 (2001) 185. 10.1179/030192301677948Suche in Google Scholar

[8] M.Cai, H.Ding, J.Zhang, L.Li, Z.Tang, C.Y.Xuebao: Chinese Journal of Materials Research.23 (2009) 83.Suche in Google Scholar

[9] M.M.Karimi, S.Kheirandish: Steel Research Int.80 (2009) 160. 10.2374/SRI08SP082Suche in Google Scholar

[10] Hongtao, Zhang, Chunfu, Huang, Ganyun, Pang: Int. Symp. on Low-Carbon Steels for the 90's, 1993, 367.Suche in Google Scholar

[11] M.H.Cai, H.Ding, J.S.Zhang, Z.Y.Tang, Wang, W.W.Kang: T'ieh/Iron and Steel (Peking)43 (2008) 77.Suche in Google Scholar

[12] G.P.Yun: Zhuzao Jishu/Foundry Tech.27 (2006) 347.Suche in Google Scholar

[13] O.Yakubovsky, N.Fonstein, C.Cheng, D.Bhattacharya: Galvatech '04: 6th International Conference on Zinc and Zinc Alloy Coated Steel Sheet – Conference Proceedings, 2004, 547.Suche in Google Scholar

[14] H.J.Bunge: Z. Metallkd.56 (1965) 872.10.1515/ijmr-1965-561213Suche in Google Scholar

[15] D.G.Brandon: Acta Mat.14 (1966) 1479. 10.1016/0001-6160(66)90168-4Suche in Google Scholar

[16] P.Van Houtte: The MTM-FHM Software System, Version 2, Department of Metallurgy and Materials Engineering, Katholieke Universiteit Leuven, Belgium.Suche in Google Scholar

[17] C.Ghosh, A.Haldar, P.Ghosh, R.K.Ray: ISIJ Int.48 (2008) 1631.Suche in Google Scholar

[18] R.Padmanabhan, A.J.Baptista, M.C.Oliveiva, L.F.Menezes: J. Mater. Process Tech.184 (2007) 288. 10.1016/j.jmatprotec.2006.11.051Suche in Google Scholar

[19] R.Ueji, N.Tsuji, Y.Minamino, Y.Koizumi: Acta Mater.50 (2002) 4177. 10.1016/S1359-6454(02)00260-4Suche in Google Scholar

[20] R.Song, D.Ponge, D.Raabe, R.Kaspar: Acta Mater.53 (2005) 845. 10.1016/j.actamat.2004.10.051Suche in Google Scholar

[21] R.Saha, R.K.Ray: Scr. Mater.57 (2007) 841. 10.1016/j.scriptamat.2007.06.064Suche in Google Scholar

[22] V.Randle, H.Davies: Metal. Mater. Trans. A33 (2002) 1853. 10.1007/s11661-002-0193-3Suche in Google Scholar

Received: 2009-5-13
Accepted: 2010-7-30
Published Online: 2013-05-31
Published in Print: 2010-10-01

© 2010, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial October 2010
  5. History
  6. Interactions between dislocations and interfaces – consequences for metal and ceramic plasticity
  7. Deformation mechanisms in yttria-stabilized cubic zirconia single crystals
  8. Basic
  9. Superplasticity in nanocrystalline ceramics: pure grain boundary phenomena or not?
  10. Thermodynamic assessment of the Mn–Ni–O system
  11. Assessment of niobium segregation energy in migrating ferrite/austenite phase interfaces
  12. In-situ synthesis and characterization of Al2O3 nanostructured whiskers in Ti–Al intermetallic matrix composites
  13. Texture, structure and properties of Ni-based binary alloy tapes for HTS substrates
  14. Microstructure, texture, grain boundary characteristics and mechanical properties of a cold rolled and annealed ferrite–bainite dual phase steel
  15. Applied
  16. Microstructure and mechanical properties of differently extruded AZ31 magnesium alloy
  17. The role of talc in preparing steatite slurries suitable for spray-drying
  18. Preparation and evaluation of chitosan-gelatin composite scaffolds modified with chondroitin-6-sulphate
  19. Influence of volume fraction of martensite on the work hardening behaviour of two dual-phase steels with high and low silicon contents
  20. Controlled synthesis of prussian blue nanoparticles based on polymyxin B/sodium bis(2-ethylhexyl)sulfosuccinate/water/isooctane reverse microemulsion for glucose biosensors
  21. The melting diagram of the Ti–Dy–Sn system below 40 at.% Sn
  22. Preparation and photocatalytic properties of TiO2 film produced via spin coating
  23. DGM News
  24. Personal
https://doi.org/10.3139/146.110406
Schlagwörter für diesen Artikel
Microstructure; Texture; Grain boundary character distribution; Cold rolling; Mechanical properties

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial October 2010
  5. History
  6. Interactions between dislocations and interfaces – consequences for metal and ceramic plasticity
  7. Deformation mechanisms in yttria-stabilized cubic zirconia single crystals
  8. Basic
  9. Superplasticity in nanocrystalline ceramics: pure grain boundary phenomena or not?
  10. Thermodynamic assessment of the Mn–Ni–O system
  11. Assessment of niobium segregation energy in migrating ferrite/austenite phase interfaces
  12. In-situ synthesis and characterization of Al2O3 nanostructured whiskers in Ti–Al intermetallic matrix composites
  13. Texture, structure and properties of Ni-based binary alloy tapes for HTS substrates
  14. Microstructure, texture, grain boundary characteristics and mechanical properties of a cold rolled and annealed ferrite–bainite dual phase steel
  15. Applied
  16. Microstructure and mechanical properties of differently extruded AZ31 magnesium alloy
  17. The role of talc in preparing steatite slurries suitable for spray-drying
  18. Preparation and evaluation of chitosan-gelatin composite scaffolds modified with chondroitin-6-sulphate
  19. Influence of volume fraction of martensite on the work hardening behaviour of two dual-phase steels with high and low silicon contents
  20. Controlled synthesis of prussian blue nanoparticles based on polymyxin B/sodium bis(2-ethylhexyl)sulfosuccinate/water/isooctane reverse microemulsion for glucose biosensors
  21. The melting diagram of the Ti–Dy–Sn system below 40 at.% Sn
  22. Preparation and photocatalytic properties of TiO2 film produced via spin coating
  23. DGM News
  24. Personal
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 17.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.110406/pdf?lang=de
Button zum nach oben scrollen