Home Numerical simulation of particulate matter propagation in an indoor environment with various types of heating
Article
Licensed
Unlicensed Requires Authentication

Numerical simulation of particulate matter propagation in an indoor environment with various types of heating

  • Alibek Issakhov EMAIL logo and Aidana Alimbek
Published/Copyright: May 11, 2022

Abstract

The aim of the work is to describe the air flow in an enclosed space, which is ventilated by a diffuser, to select an appropriate turbulence model, to solve the problem using the ANSYS Fluent, to study the effect of heat sources in a room on air flow under various conditions and to simulate the movement of particulate matter. As a result, the distribution of PM2.5 particles in the room was shown, which enter the room through the diffuser. According to the data obtained, the temperature value increases with an increase in the area of the heat source, that is, with an increase in the number of batteries. The maximum temperature corresponds to a room with a warm floor, the minimum temperature is observed in a room with one battery. The obtained numerical data can be used when installing ventilation or heating devices inside buildings, when simulating the movement of harmful particles in the air, when determining the optimal ways to clean the air.


Corresponding author: Alibek Issakhov, al-Farabi Kazakh National University, av. al-Farabi 71, 050040, Almaty, Kazakhstan; Kazakh British Technical University, Almaty, Kazakhstan; and International Information Technology University, Almaty, Kazakhstan, E-mail:

Funding source: Ministry of education and science of the Republic of Kazakhstan

Award Identifier / Grant number: AP09259783

  1. Author contribution: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.

  2. Research funding: This work is supported by grant from the Ministry of education and science of the Republic of Kazakhstan (AP09259783).

  3. Conflict of interest statement: The authors declare that there is no conflict of interests regarding the publication of this paper.

References

[1] Y. Yan, X. Li, and K. Ito, “Numerical investigation of indoor particulate contaminant transport using the Eulerian–Eulerian and Eulerian–Lagrangian two-phase flow models,” Exp. Comp. Multiph. Fl., vol. 2, no. 1, pp. 31–40, 2020. https://doi.org/10.1007/s42757-019-0016-z.Search in Google Scholar PubMed PubMed Central

[2] T. T. Zhang, K. Lee, and Q. Y. Chen, “A simplified approach to describe complex diffusers in displacement ventilation for CFD simulations,” Indoor Air, vol. 19, no. 3, pp. 255–267, 2009. https://doi.org/10.1111/j.1600-0668.2009.00590.x.Search in Google Scholar PubMed

[3] R. Goyal and P. Kumar, “Indoor–outdoor concentrations of particulate matter in nine microenvironments of a mix-use commercial building in megacity Delhi,” Air Qual. Atmos. Health, vol. 6, pp. 747–757, 2013. https://doi.org/10.1007/s11869-013-0212-0.Search in Google Scholar

[4] E. Krugly, D. Martuzevicius, R. Sidaraviciute, et al.., “Characterization of particulate and vapor phase polycyclic aromatic hydrocarbons in indoor and outdoor air of primary schools,” Atmos. Environ., vol. 82, pp. 298–306, 2014. https://doi.org/10.1016/j.atmosenv.2013.10.042.Search in Google Scholar

[5] S.-C. Lee, M. Chang, and K.-Y. Chan, “Indoor and outdoor air quality investigation at six residential buildings in Hong Kong,” Environ. Int., vol. 25, pp. 489–496, 1999. https://doi.org/10.1016/s0160-4120(99)00014-8.Search in Google Scholar

[6] G. Loupa, I. Kioutsioukis, and S. Rapsomanikis, “Indoor-outdoor atmospheric particulate matter relationships in naturally ventilated offices,” Indoor Built Environ., vol. 16, pp. 63–69, 2007. https://doi.org/10.1177/1420326x06074895.Search in Google Scholar

[7] A. Patnaik, V. Kumar, and P. Saha, “Importance of indoor environmental quality in green buildings,” in Environmental Pollution, Singapore, Springer, 2018, pp. 53–64.10.1007/978-981-10-5792-2_5Search in Google Scholar

[8] N. Zhang, H. Huang, B. Su, X. Ma, and Y. Li, “A human behavior integrated hierarchical model of airborne disease transmission in a large city,” Build. Environ., vol. 127, pp. 211–220, 2018. https://doi.org/10.1016/j.buildenv.2017.11.011.Search in Google Scholar PubMed PubMed Central

[9] F. Davardoost and D. Kahforoushan, “Health risk assessment of VOC emissions in laboratory rooms via a modeling approach,” Environ. Sci. Pollut. Control Ser., vol. 25, no. 18, pp. 17890–17900, 2018. https://doi.org/10.1007/s11356-018-1982-6.Search in Google Scholar PubMed

[10] R. B. Gammage, “Evaluation of changes in indoor air quality occurring over the past several decades,” in Indoor Air and Human Health, Boca Raton, CRC Press, 2018, pp. 19–52.10.1201/9781351073479-3Search in Google Scholar

[11] J. E. C. Lerner, M. L. Elordi, M. A. Orte, et al.., “Exposure and risk analysis to particulate matter, metals, and polycyclic aromatic hydrocarbon at different workplaces in Argentina,” Environ. Sci. Pollut. Res., vol. 25, no. 9, pp. 8487–8496, 2018. https://doi.org/10.1007/s11356-017-1101-0.Search in Google Scholar PubMed

[12] L. Du, S. Batterman, E. Parker, et al.., “Particle concentrations and effectiveness of freestanding air filters in bedrooms of children with asthma in Detroit, Michigan,” Build. Environ., vol. 46, pp. 2303–2313, 2011. https://doi.org/10.1016/j.buildenv.2011.05.012.Search in Google Scholar PubMed PubMed Central

[13] N. Y. Y. Razali, M. T. Latif, D. Dominick, N. Mohamad, F. R. Sulaiman, and T. Srithawirat, “Concentration of particulate matter, CO and CO2 in selected schools in Malaysia,” Build. Environ., vol. 87, pp. 108–116, 2015. https://doi.org/10.1016/j.buildenv.2015.01.015.Search in Google Scholar

[14] C. Ramos, H. Wolterbeek, and S. Almeida, “Exposure to indoor air pollutants during physical activity in fitness centers,” Build. Environ., vol. 82, pp. 349–360, 2014. https://doi.org/10.1016/j.buildenv.2014.08.026.Search in Google Scholar

[15] S. Lee, S. Lam, and H. K. Fai, “Characterization of VOCs, ozone, and PM10 emissions from office equipment in an environmental chamber,” Build. Environ., vol. 36, pp. 837–842, 2001. https://doi.org/10.1016/s0360-1323(01)00009-9.Search in Google Scholar

[16] R. Zhuang, X. Li, and J. Tu, “CFD study of the effects of furniture layout on indoor air quality under typical office ventilation schemes,” in Building Simulation, vol. 7, Heidelberg, Berlin, Springer, 2014, pp. 263–275.10.1007/s12273-013-0144-5Search in Google Scholar

[17] F. Bauman and A. Daly, Under Floor Air Distribution (UF AD) Design Guide, Atlanta, GA, ASHRAE, 2003.Search in Google Scholar

[18] Q. Chen and L. Glicksman, System Performance Evaluation and Design Guidelines for Displacement Ventilation, Altanta, GA, ASHRAE, 2003.Search in Google Scholar

[19] K. W. D. Cheong, E. Djunaedy, Y. L. Chua, et al.., “Thermal comfort study of an air-conditioned lecture theatre in the tropics,” Build. Environ., vol. 38, pp. 63–73, 2003. https://doi.org/10.1016/s0360-1323(02)00020-3.Search in Google Scholar

[20] A. I. Stamou, I. Katsiris, and A. Schaelin, “Evaluation of thermal comfort in Galatsi arena of the Olympics ‘Athens 2004’ using a CFD model,” Appl. Therm. Eng., vol. 28, pp. 1206–1215, 2008. https://doi.org/10.1016/j.applthermaleng.2007.07.020.Search in Google Scholar

[21] Y. Riachi and D. Clodic, “A numerical model for simulating thermal comfort prediction in public transportation buses,” Int. J. Environ. Protect. Pol., vol. 2, pp. 1–8, 2014. https://doi.org/10.11648/j.ijepp.20140201.11.Search in Google Scholar

[22] A. Simone, B. W. Olesen, J. L. Stoops, and A. W. Watkins, “Thermal comfort in commercial kitchens (RP-1469): procedure and physical measurements (part 1),” HVAC R Res., vol. 19, pp. 1001–1015, 2013. https://doi.org/10.1080/10789669.2013.840494.Search in Google Scholar

[23] F. Haghighat, Z. Jiang, and J. C. Y. Wang, “A CFD analysis of ventilation effectiveness in a partitioned room,” Indoor Air, vol. 1, no. 3, p. 606–615, 1991. https://doi.org/10.1111/j.1600-0668.1991.00022.x.Search in Google Scholar

[24] F. Haghighat, J. Jiang, and Y. Zhang, “The impact of ventilation rate and partition layout on the VOC emission rate: time-dependent contaminant removal,” Indoor Air, vol. 4, p. 276–283, 1994. https://doi.org/10.1111/j.1600-0668.1994.00008.x.Search in Google Scholar

[25] J. S. Zhang, L. L. Christianson, G. J. Wu, and R. H. Zhang, “An experimental evaluation of a numerical simulation model for prediction room air motion,” in Proceedings of Indoor Air Quality, Ventilation and Energy Conservation Conference, Montreal, Canada, 1992, pp. 360–371.Search in Google Scholar

[26] Q. Chen and Z. Jiang, “Evaluation of air supply method in a classroom with a low ventilation rate,” in Proceedings of Indoor Air Quality, Ventilation and Energy Conservation Conference, Montreal, Canada, 1992, pp. 412–419.Search in Google Scholar

[27] Z. Lei, C. Liu, L. Wang, and N. Li, “Effect of natural ventilation on indoor air quality and thermal comfort in dormitory during winter,” Build. Environ., vol. 125, pp. 240–247, 2017. https://doi.org/10.1016/j.buildenv.2017.08.051.Search in Google Scholar

[28] J. Lau and Q. Chen, “Energy analysis for workshops with floor-supply displacement ventilation under U.S. climates,” Energy Build., vol. 38, pp. 1212–1219, 2006. https://doi.org/10.1016/j.enbuild.2006.02.006.Search in Google Scholar

[29] B. Wachenfeldt, M. Mysen, and P. Schild, “Air flow rates and energy saving potential in schools with demand-controlled displacement ventilation,” Energy Build., vol. 39, pp. 1073–1079, 2007. https://doi.org/10.1016/j.enbuild.2006.10.018.Search in Google Scholar

[30] N. Djongyang, R. Tchinda, and D. Njomo, “Thermal comfort: a review paper,” Renew. Sustain. Energy Rev., vol. 14, pp. 2626–2640, 2010. https://doi.org/10.1016/j.rser.2010.07.040.Search in Google Scholar

[31] Z. Wang, M. Luo, Y. Geng, B. Lin, and Y. Zhu, “A model to compare convective and radiant heating systems for intermittent space heating,” Appl. Energy, vol. 215, pp. 211–226, 2018. https://doi.org/10.1016/j.apenergy.2018.01.088.Search in Google Scholar

[32] F. Causone, B. W. Olesen, and S. P. Corgnati, “Floor heating with displacement ventilation: an experimental and numerical analysis,” HVACR Res., vol. 16, no. 2, pp. 139–160, 2010. https://doi.org/10.1080/10789669.2010.10390898.Search in Google Scholar

[33] M. Krajcık, R. Tomasi, A. Simone, and B. W. Olesen, “Experimental study including subjective evaluations of mixing and displacement ventilation combined with radiant floor heating/cooling system,” HVACR Res., vol. 19, no. 8, pp. 1063–1072, 2013.10.1080/10789669.2013.806173Search in Google Scholar

[34] B. W. Olesen, A. Simone, M. Krajcik, F. Causone, and M. De Carli, “Experimental study of air distribution and ventilation effectiveness in a room with a combination of different mechanical ventilation and heating/cooling systems,” Int. J. Vent., vol. 9, no. 4, pp. 371–384, 2011. https://doi.org/10.1080/14733315.2011.11683895.Search in Google Scholar

[35] S. Riffat, X. Zhao, and P. Doherty, “Review of research into and application of chilled ceilings and displacement ventilation systems in Europe,” Int. J. Energy Res., vol. 28, pp. 257–286, 2004. https://doi.org/10.1002/er.964.Search in Google Scholar

[36] E. Cuce, F. Sher, H. Sadiq, P. M. Cuce, T. Guclu, and A. B. Besir, “Sustainable ventilation strategies in buildings: CFD research,” Sust. Ener. Tech. Ass., vol. 36, p. 100540, 2019. https://doi.org/10.1016/j.seta.2019.100540.Search in Google Scholar

[37] G. Einberg, K. Hagström, P. Mustakallio, H. Koskela, and S. Holmberg, “CFD modelling of an industrial air diffuser - predicting velocity and temperature in the near zone,” Build. Environ., vol. 40, no. 5, pp. 601–615, 2005. https://doi.org/10.1016/j.buildenv.2004.08.020.Search in Google Scholar

[38] A. Hasan, “Tracking the flu virus in a room mechanical ventilation using CFD tools and effective disinfection of an HVAC system,” Int. J. Air-Cond. Refrig., vol. 28, no. 2, 2020. https://doi.org/10.1142/s2010132520500194.Search in Google Scholar

[39] Q. He, J. Niu, N. Gao, T. Zhu, and J. Wu, “CFD study of exhaled droplet transmission between occupants under different ventilation strategies in a typical office room,” Build. Environ., vol. 46, no. 2, pp. 397–408, 2011. https://doi.org/10.1016/j.buildenv.2010.08.003.Search in Google Scholar PubMed PubMed Central

[40] M. Rimár, A. Kulikov, M. Fedak, and M. Abraham, “CFD analysis of the ventilation heating system,” Mech. Ind., vol. 20, no. 7, p. 708, 2019. https://doi.org/10.1051/meca/2020020.Search in Google Scholar

[41] J. Srebric and Q. Chen, “Simplified numerical models for complex air supply diffusers,” HVACR Res., vol. 8, no. 3, pp. 277–294, 2002. https://doi.org/10.1080/10789669.2002.10391442.Search in Google Scholar

[42] Y. Sun and T. Smith, “Air flow characteristics of a room with square cone diffusers,” Build. Environ., vol. 40, no. 5, pp. 589–600, 2005. https://doi.org/10.1016/j.buildenv.2004.07.018.Search in Google Scholar

[43] K. Gangisetti, D. E. Claridge, J. Srebric, and M. T. Paulus, “Influence of reduced VAV flow settings on indoor thermal comfort in an office space,” Building Simulat., vol. 9, no. 1, pp. 101–111, 2016. https://doi.org/10.1007/s12273-015-0254-3.Search in Google Scholar

[44] B. Deng, J. Wang, J. Tang, and J. Gao, “Improvement of the momentum method as the diffuser boundary condition in CFD simulation of indoor airflow: discretization viewpoint,” Build. Environ., vol. 141, 2018. https://doi.org/10.1016/j.buildenv.2018.05.050.Search in Google Scholar

[45] A. Issakhov and P. Omarova, “Numerical simulation of pollutant dispersion in the residential areas with continuous grass barriers,” Int. J. Environ. Sci. Technol., vol. 17, pp. 525–540, 2020. https://doi.org/10.1007/s13762-019-02517-x.Search in Google Scholar

[46] A. Issakhov, P. Omarova, and A. Issakhov, “Numerical study of thermal influence to pollutant dispersion in the idealized urban street road,” Air Qual. Atmo. Health, vol. 13, pp. 1045–1056, 2020. https://doi.org/10.1007/s11869-020-00856-0.Search in Google Scholar

[47] A. Issakhov, A. Alimbek, and Y. Zhandaulet, “The assessment of water pollution by chemical reaction products from the activities of industrial facilities: numerical study,” J. Clean. Prod., vol. 282, p. 125239, 2021. https://doi.org/10.1016/j.jclepro.2020.125239.Search in Google Scholar

[48] A. Issakhov, R. Bulgakov, and Y. Zhandaulet, “Numerical simulation of the dynamics of particle motion with different sizes,” Eng. Appl. of Comp. Fl. Mech., vol. 13, no. 1, pp. 1–25, 2019. https://doi.org/10.1080/19942060.2018.1545253.Search in Google Scholar

[49] F. Toja-Silva, J. Chen, S. Hachinger, and F. Hase, “CFD simulation of dispersion from urban thermal power plant: analysis of turbulent Schmidt number and comparison with Gaussian plume model and measurements,” J. Wind Eng. Ind. Aerodyn., vol. 169, pp. 177–193, 2017.10.1016/j.jweia.2017.07.015Search in Google Scholar

[50] A. Issakhov and P. Omarova, “Modeling and analysis of the effects of barrier height on automobiles emission dispersion,” J. Clean. Prod., vol. 296, p. 126450, 2021. https://doi.org/10.1016/j.jclepro.2021.126450.Search in Google Scholar

[51] A. Issakhov, A. Alimbek, and A. Issakhov, “A numerical study for the assessment of air pollutant dispersion with chemical reactions from a thermal power plant,” Eng. Appl. of Comp. Fl. Mech., vol. 14, no. 1, pp. 1035–1061, 2020. https://doi.org/10.1080/19942060.2020.1800515.Search in Google Scholar

[52] A. Issakhov, Y. Zhandaulet, P. Omarova, A. Alimbek, A. Borsikbayeva, and A. Mustafayeva, “A numerical assessment of social distancing of preventing airborne transmission of COVID-19 during different breathing and coughing processes,” Sci. Rep., vol. 11, p. 9412, 2021. https://doi.org/10.1038/s41598-021-88645-2.Search in Google Scholar PubMed PubMed Central

[53] A. Issakhov and Y. Zhandaulet, “Numerical simulation of thermal pollution zones’ formations in the water environment from the activities of the power plant,” Eng. Appl. of Comp. Fl. Mech., vol. 13, no. 1, pp. 279–299, 2019. https://doi.org/10.1080/19942060.2019.1584126.Search in Google Scholar

[54] S. V. Patankar, Numerical Heat Transfer and Fluid Flow, Boca Raton, CRC Press, 1980, p. 20.Search in Google Scholar

[55] M. Ewert, U. Renz, N. Vogl, and M. Zeller, “Definition of the flow parameters at the room inlet devices-measurements and calculations,” in Proc. of 12th AIVC Conference, 1991.Search in Google Scholar

[56] S. Fatemiardestani, Experimental and Numerical Study of an Indoor Displacement Ventilation System, Canada, University of Manitoba, 2013.Search in Google Scholar

[57] A. Issakhov, A. Borsikbayeva, “The impact of a multilevel protection column on the propagation of a water wave and pressure distribution during a dam break: numerical simulation,” Journal of Hydrology, vol. 598, no. 126212, 2021. https://doi.org/10.1016/j.jhydrol.2021.126212.Search in Google Scholar

[58] A. Issakhova, A. Tursynzhanova, and A. Abylkassymova, “Numerical study of air pollution exposure in idealized urban street canyons: porous and solid barriers,” Urban Climate, vol. 43, no. 101112, 2022. https://doi.org/10.1016/j.uclim.2022.101112.Search in Google Scholar

Received: 2021-03-12
Revised: 2021-07-08
Accepted: 2021-11-04
Published Online: 2022-05-11

© 2021 Walter de Gruyter GmbH, Berlin/Boston

Articles in the same Issue

  1. Frontmatter
  2. Original Research Articles
  3. Numerical solutions for variable-order fractional Gross–Pitaevskii equation with two spectral collocation approaches
  4. Threshold dynamics of an HIV-1 model with both virus-to-cell and cell-to-cell transmissions, immune responses, and three delays
  5. Numerical scheme and analytical solutions to the stochastic nonlinear advection diffusion dynamical model
  6. On modeling column crystallizers and a Hermite predictor–corrector scheme for a system of integro-differential equations
  7. On a discrete fractional stochastic Grönwall inequality and its application in the numerical analysis of stochastic FDEs involving a martingale
  8. A new self adaptive Tseng’s extragradient method with double-projection for solving pseudomonotone variational inequality problems in Hilbert spaces
  9. Solitary waves of the RLW equation via least squares method
  10. Optical solitons and stability regions of the higher order nonlinear Schrödinger’s equation in an inhomogeneous fiber
  11. Weighted pseudo asymptotically Bloch periodic solutions to nonlocal Cauchy problems of integrodifferential equations in Banach spaces
  12. Modified inertial subgradient extragradient method for equilibrium problems
  13. Propagation of dark-bright soliton and kink wave solutions of fluidized granular matter model arising in industrial applications
  14. Existence and uniqueness of positive solutions for fractional relaxation equation in terms of ψ-Caputo fractional derivative
  15. Investigation of nonlinear fractional delay differential equation via singular fractional operator
  16. Travelling peakon and solitary wave solutions of modified Fornberg–Whitham equations with nonhomogeneous boundary conditions
  17. The (3 + 1)-dimensional Wazwaz–KdV equations: the conservation laws and exact solutions
  18. Stability and ψ-algebraic decay of the solution to ψ-fractional differential system
  19. Some new characterizations of a space curve due to a modified frame N , C , W in Euclidean 3-space
  20. Numerical simulation of particulate matter propagation in an indoor environment with various types of heating
  21. Inertial accelerated algorithms for solving split feasibility with multiple output sets in Hilbert spaces
  22. Stability analysis and abundant closed-form wave solutions of the Date–Jimbo–Kashiwara–Miwa and combined sinh–cosh-Gordon equations arising in fluid mechanics
  23. Contrasting effects of prey refuge on biodiversity of species
Downloaded on 1.10.2025 from https://www.degruyterbrill.com/document/doi/10.1515/ijnsns-2021-0104/html
Scroll to top button