Startseite High-temperature plasticity of SiC sintered with Lu2O3-AlN additives
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

High-temperature plasticity of SiC sintered with Lu2O3-AlN additives

  • Georg Rixecker EMAIL logo und Koushik Biswas
Veröffentlicht/Copyright: 11. Januar 2022
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 97 Heft 6

Abstract

SiC ceramics containing Lu2O3–AlN sintering additives were gas-pressure sintered, and creep testing in four-point bending geometry was performed at temperatures between 1200 °C and 1500 °C in air. Compared with the more conventional additive system Y2O3 –AlN, the creep resistance of the Lu2O3-containing ceramics is higher. In particular, strain rates down to 6 ⨯ 10–10 s–1 were measured after 60 h at both 1300 °C/300 MPa and 1400 °C/100 MPa; in no case was steady-state creep reached. Annealing the ceramics at 1950 °C for extended periods of time led to significant changes in the amount and distribution of intergranular phases. However, in contrast to earlier work using Y2O3 –AlN additives, the influence of annealing on the creep resistance was negligible. Compliance testing as a function of temperature was conducted in order to monitor the softening behavior of materials with different additive compositions. In favorable cases, the drop in stiffness was only 12% up to a test temperature of 1450 °C.

Keywords: Silicon carbide; Lutetium oxide; Liquid phase sintering; Creep; Compliance

Max-Planck Institut für Metallforschung and Institut für Nichtmetallische Anorganische Materialien, Universität Stuttgart, Stuttgart, Germany

Dedicated to Professor Dr. Fritz Aldinger on the occasion of his 65th birthday

Dr. Georg Rixecker Robert Bosch GmbH Corporate Research and Advance Engineering (CR/ART2) Postfach 10 60 50, D-70049 Stuttgart, Germany Tel.: +49 711 811 7050

  1. The authors wish to thank Mr Reinhard Mager for his assistance with the creep testing.

References

[1] N.P. Padture: J. Am. Ceram. Soc. 77 (1994) 519.10.1111/j.1151-2916.1994.tb07024.xSuche in Google Scholar

[2] M.A. Mulla, V.D. Krstic: Acta. Metall. Mater. 42 (1994) 303.10.1016/0956-7151(94)90072-8Suche in Google Scholar

[3] S.K. Lee, D.K. Kim, C.K. Kim: J. Am. Ceram. Soc. 78 (1995) 65.10.1111/j.1151-2916.1995.tb08361.xSuche in Google Scholar

[4] Y.W. Kim, M. Mitomo, H. Hirotsuru: J. Am. Ceram. Soc. 80 (1997) 99.10.1111/j.1151-2916.1997.tb02796.xSuche in Google Scholar

[5] Z.C. Jou, A.V. Virkar, R.A. Cutler: J. Mater. Res. 6 (1991) 1945.10.1557/JMR.1991.1945Suche in Google Scholar

[6] J.E. Lane, C.H. Carter, R.F. Davis: J. Am. Ceram. Soc. 71 (1988) 281.10.1111/j.1151-2916.1988.tb05861.xSuche in Google Scholar

[7] R.D. Nixon, R.F. Davis: J. Am. Ceram. Soc. 75 (1992) 1786.10.1111/j.1151-2916.1992.tb07198.xSuche in Google Scholar

[8] A. Gallardo-López, A. Muñoz, J. Martínez-Fernández, A. Domínguez-Rodríguez: Acta Mater. 47 (1999) 2185.10.1016/S1359-6454(99)00072-5Suche in Google Scholar

[9] S.M. Wiederhorn, B.J. Hockey, J.D. French: J. Eur. Ceram. Soc. 19 (1999) 2273.10.1016/S0955-2219(99)00121-1Suche in Google Scholar

[10] Y.W. Kim, M. Mitomo, T. Nishimura: J. Am. Ceram. Soc. 85 (2002) 1007.10.1111/j.1151-2916.2002.tb00211.xSuche in Google Scholar

[11] T. Nagano, H. Gu, G.D. Zhan, M. Mitomo: J. Mater. Sci. 37 (2002) 4419.10.1023/A:1020629308663Suche in Google Scholar

[12] A.L. Ortiz, A. Muñoz-Bernabé, O. Borrero-López, A. Domínguez-Rodríguez, F. Guiberteau, N.P. Padture: J. Eur. Ceram. Soc. 24 (2004) 3245.10.1016/j.jeurceramsoc.2003.10.047Suche in Google Scholar

[13] G. Rixecker, K. Biswas, I. Wiedmann, F. Aldinger: J. Ceram. Proc. Res. 1 (2000) 19.Suche in Google Scholar

[14] K. Biswas, G. Rixecker, I. Wiedmann, M. Schweizer, G.S. Upadhyaya, F. Aldinger: Mater. Chem. Phys. 67 (2001) 180.10.1016/S0254-0584(00)00437-5Suche in Google Scholar

[15] J.R. Dryden, D. Kucerovsky, D.S. Wilkinson, D.F.Watt: Acta Metall. 37 (1989) 2007.10.1016/0001-6160(89)90085-0Suche in Google Scholar

[16] D.S. Wilkinson: J. Am. Ceram. Soc. 81 (1998) 275.10.1111/j.1151-2916.1998.tb02333.xSuche in Google Scholar

[17] G. Pezzotti, H.-J. Kleebe, H. Nishimura, K. Ota: J. Am. Ceram. Soc. 84 (2001) 2371.10.1111/j.1151-2916.2001.tb01017.xSuche in Google Scholar

[18] K. Biswas, G. Rixecker, F. Aldinger, in: P. Vincenzini et al. (Eds.), Proc. CIMTEC 2002, 10th Intern. Ceram. Congr. – Part C, Techna Publ., Florence (2002) p. 791.Suche in Google Scholar

[19] M.A. Mulla, V.D. Krstic: Am. Ceram. Soc. Bull. 70 (1991) 439.Suche in Google Scholar

[20] K. Suzuki, in: S. Somiya, Y. Inomata (Eds.), Silicon Carbide Ceramics-I, Elsevier, Barking (1991) p. 163.Suche in Google Scholar

[21] Y.W. Kim, M. Mitomo, H. Hirotsuru,: J. Am. Ceram. Soc. 78 (1995) 3145.10.1111/j.1151-2916.1995.tb09100.xSuche in Google Scholar

[22] M. Nader: Doctoral Thesis, University of Stuttgart, Stuttgart (1995).Suche in Google Scholar

[23] H.W. Jun, H.W. Lee, G.H. Kim, H.S. Song, B.H. Kim: Ceram. Engg. and Sci. Proc. 18 (1997) 487.10.1002/9780470294444.ch57Suche in Google Scholar

[24] Z. Chen: J. Am. Ceram. Soc. 79 (1996) 530.10.1111/j.1151-2916.1996.tb08160.xSuche in Google Scholar

[25] Y.W. Kim, M. Mitomo, T. Nishimura: J. Am. Ceram. Soc. 84 (2001) 2060.10.1111/j.1151-2916.2001.tb00958.xSuche in Google Scholar

[26] F. Lofaj, S.M. Wiederhorn, G.G. Long, B.J. Hockey, P.R. Jemian, L. Browder, J. Andreason, U. Täffner: J. Eur. Ceram. Soc. 22 (2002) 2479.10.1016/S0955-2219(02)00106-1Suche in Google Scholar

[27] H. Ye, G. Rixecker, S. Haug, F. Aldinger: J. Eur. Ceram. Soc. 22 (2002) 2379.10.1016/S0955-2219(02)00006-7Suche in Google Scholar

[28] S. Hampshire: J. Non-Cryst. Solids 316 (2003) 64.10.1016/S0022-3093(02)01938-5Suche in Google Scholar

[29] J.A. Schneider, K. Biswas, G. Rixecker, F. Aldinger: J. Am. Ceram. Soc. 86 (2003) 501.10.1111/j.1151-2916.2003.tb03328.xSuche in Google Scholar

[30] P.F. Becher: J. Am. Ceram. Soc. 74 (1991) 255.10.1111/j.1151-2916.1991.tb06872.xSuche in Google Scholar

[31] M. Mizuno, S. Zhu, Y. Kagawa, H. Kaya,: J. Eur. Ceram. Soc. 18 (1998) 1869.10.1016/S0955-2219(98)00126-5Suche in Google Scholar

[32] T. Rouxel, J.L. Besson, C. Gault, P. Goursat, M. Leigh, S. Hampshire: J. Mater. Sci. Lett. 8 (1989) 1158.10.1007/BF01730054Suche in Google Scholar

[33] P. Gadaud, S. Pautrot: J. Non-Cryst. Solids 316 (2003) 146.10.1016/S0022-3093(02)01947-6Suche in Google Scholar

[34] L. An, R. Riedel, C. Konetschny, H.J. Kleebe, R. Raj: J. Am. Ceram. Soc. 81 (1998) 1349.10.1111/j.1151-2916.1998.tb02489.xSuche in Google Scholar

[35] F. Lofaj, S. Dériano, M. LeFloch, T. Rouxel, M.J. Hoffmann: J. Non-Cryst. Solids 44 (2004) 8.10.1016/j.jnoncrysol.2004.07.018Suche in Google Scholar
Received: 2005-10-26
Accepted: 2006-02-11
Published Online: 2022-01-11

© 2006 Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Frontmatter
  2. Microstructure and mechanical behavior of Pt-modified NiAl diffusion coatings
  3. Evolution of C-rich SiOC ceramics
  4. Evolution of C-rich SiOC ceramics
  5. Nanostructured SiC/BN/C ceramics derived from mixtures of B3N3H6 and [HSi(Me)C≡C]n
  6. Thermodynamic analysis of structural transformations induced by annealing of amorphous Si–C–N ceramics derived from polymer precursors
  7. Thermodynamic modelling of the Ce–Ni system
  8. Thermodynamic assessment of the Ce–O system in solid state from 60 to 67 mol.% O
  9. Phase transformations of iron nitrides at low temperatures (< 700 K) – application of mechanical mixtures of powders of nitrides and iron
  10. Effect of organic self-assembled monolayers on the deposition and adhesion of hydroxyapatite coatings on titanium
  11. Reconstruction and structural transition at metal/diamond interfaces
  12. Microstructure, hardness, and fracture toughness evolution of hot-pressed SiC/Si3N4 nano/micro composite after high-temperature treatment
  13. High-temperature plasticity of SiC sintered with Lu2O3-AlN additives
  14. Interaction of functionalised surfaces on silica with dissolved metal cations in aqueous solutions
  15. XRD and TEM study of NiO–LSGM reactivity
  16. Microstructure and dielectric properties of nanoscale oxide layers on sintered capacitor-grade niobium and V-doped niobium powder compacts
  17. Knudsen effusion mass spectrometric studies of the Al–Ni system: Thermodynamic properties over {AlNi + Al3Ni2} and {Al3Ni2 + Al3Ni}
  18. Aqueous solution deposition of indium hydroxide and indium oxide columnar type thin films
  19. Thermodynamic properties of B2-AlFeNi alloys: modelling of the B2-AlFe and B2-AlNi phases
  20. Kinetics of precipitate formation in (TixWyCrz)B2 solid solutions: influence of Cr concentration and Co impurities
  21. On the mechanisms governing the texture and microstructure evolution during static recrystallization and grain growth of low alloyed zirconium sheets (Zr702)
  22. Out-of-pile chemical compatibility of Pb–Bi eutectic alloy with Graphite
  23. Microstructural characterisation of a Co–Cr–Mo laser clad applied on railway wheels
  24. The Na–H system: from first-principles calculations to thermodynamic modeling
  25. Personal
  26. Conferences
  27. Frontmatter
  28. Basic
  29. Microstructure and mechanical behavior of Pt-modified NiAl diffusion coatings
  30. Evolution of C-rich SiOC ceramics
  31. Evolution of C-rich SiOC ceramics
  32. Nanostructured SiC/BN/C ceramics derived from mixtures of B3N3H6 and [HSi(Me)C≡C]n
  33. Thermodynamic analysis of structural transformations induced by annealing of amorphous Si–C–N ceramics derived from polymer precursors
  34. Thermodynamic modelling of the Ce–Ni system
  35. Thermodynamic assessment of the Ce–O system in solid state from 60 to 67 mol.% O
  36. Phase transformations of iron nitrides at low temperatures (< 700 K) – application of mechanical mixtures of powders of nitrides and iron
  37. Effect of organic self-assembled monolayers on the deposition and adhesion of hydroxyapatite coatings on titanium
  38. Reconstruction and structural transition at metal/diamond interfaces
  39. Applied
  40. Microstructure, hardness, and fracture toughness evolution of hot-pressed SiC/Si3N4 nano/micro composite after high-temperature treatment
  41. High-temperature plasticity of SiC sintered with Lu2O3-AlN additives
  42. Interaction of functionalised surfaces on silica with dissolved metal cations in aqueous solutions
  43. XRD and TEM study of NiO–LSGM reactivity
  44. Microstructure and dielectric properties of nanoscale oxide layers on sintered capacitor-grade niobium and V-doped niobium powder compacts
  45. Knudsen effusion mass spectrometric studies of the Al–Ni system: Thermodynamic properties over {AlNi + Al3Ni2} and {Al3Ni2 + Al3Ni}
  46. Aqueous solution deposition of indium hydroxide and indium oxide columnar type thin films
  47. Thermodynamic properties of B2-AlFeNi alloys: modelling of the B2-AlFe and B2-AlNi phases
  48. Regular Articles
  49. Kinetics of precipitate formation in (TixWyCrz)B2 solid solutions: influence of Cr concentration and Co impurities
  50. On the mechanisms governing the texture and microstructure evolution during static recrystallization and grain growth of low alloyed zirconium sheets (Zr702)
  51. Out-of-pile chemical compatibility of Pb–Bi eutectic alloy with Graphite
  52. Microstructural characterisation of a Co–Cr–Mo laser clad applied on railway wheels
  53. The Na–H system: from first-principles calculations to thermodynamic modeling
  54. Notifications
  55. Personal
  56. Conferences
https://doi.org/10.1515/ijmr-2006-0125
Schlagwörter für diesen Artikel
Silicon carbide; Lutetium oxide; Liquid phase sintering; Creep; Compliance

Artikel in diesem Heft

  1. Frontmatter
  2. Microstructure and mechanical behavior of Pt-modified NiAl diffusion coatings
  3. Evolution of C-rich SiOC ceramics
  4. Evolution of C-rich SiOC ceramics
  5. Nanostructured SiC/BN/C ceramics derived from mixtures of B3N3H6 and [HSi(Me)C≡C]n
  6. Thermodynamic analysis of structural transformations induced by annealing of amorphous Si–C–N ceramics derived from polymer precursors
  7. Thermodynamic modelling of the Ce–Ni system
  8. Thermodynamic assessment of the Ce–O system in solid state from 60 to 67 mol.% O
  9. Phase transformations of iron nitrides at low temperatures (< 700 K) – application of mechanical mixtures of powders of nitrides and iron
  10. Effect of organic self-assembled monolayers on the deposition and adhesion of hydroxyapatite coatings on titanium
  11. Reconstruction and structural transition at metal/diamond interfaces
  12. Microstructure, hardness, and fracture toughness evolution of hot-pressed SiC/Si3N4 nano/micro composite after high-temperature treatment
  13. High-temperature plasticity of SiC sintered with Lu2O3-AlN additives
  14. Interaction of functionalised surfaces on silica with dissolved metal cations in aqueous solutions
  15. XRD and TEM study of NiO–LSGM reactivity
  16. Microstructure and dielectric properties of nanoscale oxide layers on sintered capacitor-grade niobium and V-doped niobium powder compacts
  17. Knudsen effusion mass spectrometric studies of the Al–Ni system: Thermodynamic properties over {AlNi + Al3Ni2} and {Al3Ni2 + Al3Ni}
  18. Aqueous solution deposition of indium hydroxide and indium oxide columnar type thin films
  19. Thermodynamic properties of B2-AlFeNi alloys: modelling of the B2-AlFe and B2-AlNi phases
  20. Kinetics of precipitate formation in (TixWyCrz)B2 solid solutions: influence of Cr concentration and Co impurities
  21. On the mechanisms governing the texture and microstructure evolution during static recrystallization and grain growth of low alloyed zirconium sheets (Zr702)
  22. Out-of-pile chemical compatibility of Pb–Bi eutectic alloy with Graphite
  23. Microstructural characterisation of a Co–Cr–Mo laser clad applied on railway wheels
  24. The Na–H system: from first-principles calculations to thermodynamic modeling
  25. Personal
  26. Conferences
  27. Frontmatter
  28. Basic
  29. Microstructure and mechanical behavior of Pt-modified NiAl diffusion coatings
  30. Evolution of C-rich SiOC ceramics
  31. Evolution of C-rich SiOC ceramics
  32. Nanostructured SiC/BN/C ceramics derived from mixtures of B3N3H6 and [HSi(Me)C≡C]n
  33. Thermodynamic analysis of structural transformations induced by annealing of amorphous Si–C–N ceramics derived from polymer precursors
  34. Thermodynamic modelling of the Ce–Ni system
  35. Thermodynamic assessment of the Ce–O system in solid state from 60 to 67 mol.% O
  36. Phase transformations of iron nitrides at low temperatures (< 700 K) – application of mechanical mixtures of powders of nitrides and iron
  37. Effect of organic self-assembled monolayers on the deposition and adhesion of hydroxyapatite coatings on titanium
  38. Reconstruction and structural transition at metal/diamond interfaces
  39. Applied
  40. Microstructure, hardness, and fracture toughness evolution of hot-pressed SiC/Si3N4 nano/micro composite after high-temperature treatment
  41. High-temperature plasticity of SiC sintered with Lu2O3-AlN additives
  42. Interaction of functionalised surfaces on silica with dissolved metal cations in aqueous solutions
  43. XRD and TEM study of NiO–LSGM reactivity
  44. Microstructure and dielectric properties of nanoscale oxide layers on sintered capacitor-grade niobium and V-doped niobium powder compacts
  45. Knudsen effusion mass spectrometric studies of the Al–Ni system: Thermodynamic properties over {AlNi + Al3Ni2} and {Al3Ni2 + Al3Ni}
  46. Aqueous solution deposition of indium hydroxide and indium oxide columnar type thin films
  47. Thermodynamic properties of B2-AlFeNi alloys: modelling of the B2-AlFe and B2-AlNi phases
  48. Regular Articles
  49. Kinetics of precipitate formation in (TixWyCrz)B2 solid solutions: influence of Cr concentration and Co impurities
  50. On the mechanisms governing the texture and microstructure evolution during static recrystallization and grain growth of low alloyed zirconium sheets (Zr702)
  51. Out-of-pile chemical compatibility of Pb–Bi eutectic alloy with Graphite
  52. Microstructural characterisation of a Co–Cr–Mo laser clad applied on railway wheels
  53. The Na–H system: from first-principles calculations to thermodynamic modeling
  54. Notifications
  55. Personal
  56. Conferences
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 2.12.2025 von https://www.degruyterbrill.com/document/doi/10.1515/ijmr-2006-0125/pdf?lang=de
Button zum nach oben scrollen